DP980+Z烘烤硬化值与退火温度的关系

摘要：为了研究退火温度对镀锌DP980+Z烘烤硬化值的影响，退火温度控制在760～820℃之间，系统分析退火温度对烘烤硬化值的影响。通过准静态拉伸试验机测量烘烤硬化值及抗拉强度，采用lepara试剂对组织中的马氏体进行着色，利用金相显微镜及图像处理软件测量马氏体的体积分数；采用扫描电镜观察DP980+Z的双相组织特点，并且将组织图片通过CAD转化成有限元图进行网格划分，建立代表性体积单元（RVE），通过有限元分析铁素体、马氏体强度对烘烤硬化值的影响。在同样的变形量情况下，DP980+Z的原始屈服强度越高，烘烤硬化值越高。     

Formation of a protective layer against corrosion on Mg alloy via alkali pretreatment followed by vanillic acid treatment

Although Mg alloy possesses high specific strength, low density, and good biocompatibility, poor corrosion resistance hinders its further applications. In the present study, an innovative protective layer against corrosion was prepared on the AZ31 Mg alloy via alkali pretreatment followed by vanillic acid treatment. The alkali pretreatment supplied –OH for the AZ31 Mg alloy surface to react with vanillic acid. The vanillic acid treatment played a crucial role in enhancing the corrosion resistance due to the excellent ability to act as a barrier and retard aqueous solution penetration, which effectively isolated the underlying Mg alloy from the corrosive environment. The corrosion current density of alkali and vanillic acid-treated Mg alloy (AZ31V) almost showed two orders of magnitude lower values in comparison with that of the AZ31 Mg alloy, and the corrosion potential of AZ31V Mg alloy increased from −1.41 to −1.25 V. The immersion tests proved that there was no occurrence of severe corrosion. Hence, the alkali pretreatment and vanillic acid treatment may represent a promising method to improve the corrosion resistance of Mg alloy.     

Tensor Q-rank: new data dependent definition of tensor rank

Machine Learning - Recently, the $${ Tensor}~{ Nuclear}~{ Norm}~{ (TNN)}$$ regularization based on t-SVD has been widely used in various low tubal-rank tensor recovery tasks. However, these models...     

Transformation of the reabsorption characteristics of lignite treated by low and high temperature drying process

Abstract

The reabsorption characteristics of the lignite treated by low and high temperature drying process were addressed in the paper. The information about the moisture form, functional groups, effective water-filled porosities and equilibrium moisture content of the lignite before and after the drying process was investigated using Differential scanning calorimetry (DSC), Fourier transform infrared (FTIR) spectroscopy, nuclear magnetic resonance (NMR) spectroscopy and a self-made reabsorption device, respectively. The results show that the low drying temperature (140, 190, 230?°C, 10?min, N₂) has little impact on the effective water-filled porosities of the resulted samples, whereas it has a great influence on the main oxygen-containing functional groups, which amount firstly decreases and then increases with the drying temperature increasing. In the case of the lignite samples dried under high-temperature (600, 700, 800?°C, 30?s, N₂), the amount of the effective water-filled porosity of the sample decreases and the amount of oxygen-containing functional groups increases as the temperature increasing. The reabsorption capability of the high temperature dried sample is much lower than that of the sample treated under low drying temperature. The reabsorption characteristics of the low-temperature dried samples are affected by the amount of the oxygen-containing functional groups, while the effective water-filled porosity is main factor for the lignite samples derived from high temperature drying process. Moreover, the work gives a good evidence that the high-temperature drying process is an effective choose for lignite upgrading.     

海上稠油油田蒸汽吞吐产量确定新方法

针对目前蒸汽吞吐产量预测模型假设条件简单、普适性差等问题,一般采用测试法和类比法综合确定海上稠油油田蒸汽吞吐初期产量。由于目前海上油田通常只开展常规测试,无法直接获得热采开发初期产量。笔者提出海上稠油油田蒸汽吞吐初期产量确定新方法,建立蒸汽吞吐相对于常规开发的初期产量倍数预测模型,通过蒸汽吞吐产量倍数,将常规测试确定的产量转化为蒸汽吞吐产量。研究表明,蒸汽吞吐初期产量倍数主要受储集层渗透率、原油黏度、注入强度、蒸汽干度等因素影响,利用正交试验设计和多元回归等方法,建立海上稠油油田蒸汽吞吐初期产量倍数与油藏地质参数及注入参数之间的非线性预测模型,该模型经实际生产数据验证,预测误差小于5%,可靠性高,能够为海上稠油油田蒸汽吞吐初期产量的确定提供依据。     

鄂尔多斯盆地三叠系延长组层序地层与生储盖组合特征

鄂尔多斯盆地三叠系延长组地层层序划分方案较多。在V ail经典层序地层学理论指导下,综合利用露头、岩芯、钻井、地震和古生物等资料,通过古水深分析和层序界面的识别与划分,认为将鄂尔多斯盆地三叠系延长组划分为7个三级层序更为合理,指出层序4水进体系域(生)+层序5低位体系域(储)+层序5水进体系域(盖)和层序4水进体系域(生)+层序4低位体系域(储)+层序4水进体系域(盖)是相对较佳的2套生储盖组合,并指出了鄂尔多斯盆地延长组最主要的2套生储盖勘探目的层。     

镁掺杂磷铝分子筛可见光光催化性能的初步研究

采用水热反应的方法合成了金属镁掺杂的磷铝分子筛MgAPO-5,通过XRD、DR UV-Vis、FT-IR等手段对其结构性能进行表征,并以亚甲基蓝溶液为目标降解物,在可见光下考察了MgAPO-5的光催化性能.结果表明,MgAPO-5具有与AlPO4-5相同的分子筛结构,掺杂的镁可能存在于磷铝分子筛的骨架中,在可见光下对亚甲基蓝溶液具有优良的光催化性能,反应5 h,脱色率可达92.5%.     

骆马湖生态建设

骆马湖为浅水湖泊,具有典型的过水性特征,已经处于中富营养化阶段。通过对骆马湖富营养化发生机制的研究,发现入湖河道携入大量营养物质入湖和水生植物的破坏是骆马湖富营养化进程加快的主要原因。为了保护骆马湖水质,提出对骆马湖生态建设的意见:建立自然保护区,建设入湖口人工湿地,建设骆马湖生态湖滨,通过生态渔业和生态旅游实现骆马湖的可持续开发。     

Ni-Al2O3纳米复合电镀工艺的初步研究

初步研究了复合电镀各工艺条件：电流密度、镀液pH值和温度以及搅拌方式对Al2O3纳米微粒在镍基复合镀层中含量的影响。研究表明：电流密度增大不利于提高镀层中纳米微粒的含量；pH值增大也明显使复合量降低;镀液温度升高，镀层中微粒的复合量随之略有改变；电镀时，加强搅拌或适当改变搅拌方式，可以使复合镀居中的纳米微粒含量提高。还利用扫描电镜及能谱对Ni-Al2O3镀层表面进行了观察与分析。     

关于中值定理的几点应用

本文作者给出了在两种不同类型的证明题中应用中值定理的方法.这些方法简单、实用.