Destructive and non-destructive evaluation of concrete for optimum sand to aggregate volume ratio

Aggregates are the biggest contributor to concrete volume and are a crucial parameter in dictating its mechanical properties. As such, a detailed experimental investigation was carried out to evaluate the effect of sand-to-aggregate volume ratio (s/a) on the mechanical properties of concrete utilizing both destructive and non-destructive testing (employing UPV (ultrasonic pulse velocity) measurements). For investigation, standard cylindrical concrete samples were made with different s/a (0.36, 0.40, 0.44, 0.48, 0.52, and 0.56), cement content (340 and 450 kg/m³), water-to-cement ratio (0.45 and 0.50), and maximum aggregate size (12 and 19 mm). The effect of these design parameters on the 7, 14, and 28 d compressive strength, tensile strength, elastic modulus, and UPV of concrete were assessed. The careful analysis demonstrates that aggregate proportions and size need to be optimized for formulating mix designs; optimum ratios of s/a were found to be 0.40 and 0.44 for the maximum aggregate size of 12 and 19 mm, respectively, irrespective of the W/C (water-to-cement) and cement content.     

Development and Verification of Simulation Model Based on Real MANET Experiments for Transport Layer Protocols （UDP and TCP）

There is a lack of appropriate guidelines for realistic user traces, mobility models, routing protocols, considerations of real-life challenges, etc. for general-purpose mobile ad hoc networks (MANET). In this paper, four laptops are used in an open field environment in four scenarios to evaluate the performances of Internet control message protocol (ICMP) based ping and transmission control protocol (TCP) based streaming video applications using optimised link state routing (OLSR) implementation in an IEEE 802.11g wireless network. Corresponding simulations are developed in Network Simulator ns-2 by setting simulation parameters according to the real experiments. Difficulties faced to regenerate real-life scenarios have been discussed and the gaps between reality and simulation are identified. A setup guideline to produce realistic simulation results has been established.     

A Comparison of Mamdani and Sugeno Fuzzy Based Packet Scheduler for MANET with a Realistic Wireless Propagation Model

 The mobile nature of the nodes in a wireless mobile ad-hoc network (MANET) and the error prone link connectivity between nodes pose many challenges. These include frequent route changes, high packet loss, etc. Such problems increase the end-toend delay and decrease the throughput. This paper proposes two adaptive priority packet scheduling algorithms for MANET based on Mamdani and Sugeno fuzzy inference system. The fuzzy systems consist of three input variables: data rate, signal-to-noise ratio (SNR) and queue size. The fuzzy decision system has been optimised to improve its efficiency. Both fuzzy systems were verified using the Matlab fuzzy toolbox and the performance of both algorithms were evaluated using the riverbed modeler (formally known as OPNET modeler). The results were compared to an existing fuzzy scheduler under various network loads, for constant-bit-rate (CBR) and variable-bit-rate (VBR) traffic. The measuring metrics which form the basis for performance evaluation are end-to-end delay, throughput and packet delivery ratio. The proposed Mamdani and Sugeno scheduler perform better than the existing scheduler for CBR traffic. The end-to-end delay for Mamdani and Sugeno scheduler was reduced by an average of 52% and 54%, respectively. The performance of the throughput and packet delivery ratio for CBR traffic are very similar to the existing scheduler because of the characteristic of the traffic. The network was also at full capacity. The proposed schedulers also showed a better performance for VBR traffic. The end-to-end delay was reduced by an average of 38% and 52%, respectively. Both the throughput and packet delivery ratio (PDR) increased by an average of 53% and 47%, respectively. The Mamdani scheduler is more computationally complex than the Sugeno scheduler, even though they both showed similar network performance. Thus, the Sugeno scheduler is more suitable for real-time applications.     

A New Mobile Robot Toolbox for Matlab

In this study, a wheeled mobile robot navigation toolbox for Matlab is presented. The toolbox includes algorithms for 3D map design, static and dynamic path planning, point stabilization, localization, gap detection and collision avoidance. One can use the toolbox as a test platform for developing custom mobile robot navigation algorithms. The toolbox allows users to insert/remove obstacles to/from the robot’s workspace, upload/save a customized map and configure simulation parameters such as robot size, virtual sensor position, Kalman filter parameters for localization, speed controller and collision avoidance settings. It is possible to simulate data from a virtual laser imaging detection and ranging (LIDAR) sensor providing a map of the mobile robot’s immediate surroundings. Differential drive forward kinematic equations and extended Kalman filter (EKF) based localization scheme is used to determine where the robot will be located at each simulation step. The LIDAR data and the navigation process are visualized on the developed virtual reality interface. During the navigation of the robot, gap detection, dynamic path planning, collision avoidance and point stabilization procedures are implemented. Simulation results prove the efficacy of the algorithms implemented in the toolbox.     

microRNAs Are Abundant and Stable in Platelet-Rich Fibrin and Other Autologous Blood Products of Canines

Various microRNAs (miRNAs) present in autologous blood products of canines have not been studied recently. We aimed to elucidate the existence of miRNAs in platelet-rich fibrin (PRF) and the stability of canine autologous blood products under various storage conditions. Total RNAs were isolated from PRF and other autologous blood products following newly adapted protocols used in commercial kits for plasma and tissue samples. Quantitative real-time polymerase chain reaction analysis (qPCR) was used to detect miRNAs in autologous blood products. The miR-16, miR-21, miR-155, and miR-146a were abundant in PRF and other autologous blood products of canines. Furthermore, we found they could maintain stability under protracted freezing temperatures of −30 °C for at least one month. Our findings revealed that PRF might be a stable resource for various canine miRNAs.     

Epithelial Layer Estimation Using Curvatures and Textural Features for Dysplastic Tissue Detection

Boundary effect in digital pathology is a phenomenon where the tissue shapes of biopsy samples get distorted during the sampling process. The morphological pattern of an epithelial layer is greatly affected. Theoretically, the shape deformation model can normalise the distortions, but it needs a 2D image. Curvatures theory, on the other hand, is not yet tested on digital pathology images. Therefore, this work proposed a curvature detection to reduce the boundary effects and estimates the epithelial layer. The boundary effect on the tissue surfaces is normalised using the frequency of a curve deviates from being a straight line. The epithelial layer’s depth is estimated from the tissue edges and the connected nucleolus only. Then, the textural and spatial features along the estimated layer are used for dysplastic tissue detection. The proposed method achieved better performance compared to the whole tissue regions in terms of detecting dysplastic tissue. The result shows a leap of kappa points from fair to a substantial agreement with the expert’s ground truth classification. The improved results demonstrate that curvatures have been effective in reducing the boundary effects on the epithelial layer of tissue. Thus, quantifying and classifying the morphological patterns for dysplasia can be automated. The textural and spatial features on the detected epithelial layer can capture the changes in tissue.     

Modeling of Dispersive Materials Using Dispersion Models for FDTD Application

A nonlinear optimization algorithm based on the Nelder Mead method is used to characterize the frequency dependent permittivity of 15 materials based on Lorentz, modified Lorentz, Drude and Lorentz-Drude models. The optimized model parameters are used to calculate the complex relative permittivity of each material and compare it with experimental data. In each case, a very good match is found between the optimized and experimental data over a long wavelength range. Comparative study of the models used for each material is performed based on accuracy, wavelength range of applicability and computational efficiency. The parameters presented can be used for computer simulation of electromagnetic wave phenomena involving these materials.     

Mixed convective heat transfer enhancement in a ventilated cavity by flow modulation via rotating plate

The present study numerically explores the mixed convection phenomena in a differentially heated ventilated square cavity with active flow modulation via a rotating plate. Forced convection flow in the cavity is attained by maintaining external fluid flow through an opening at the bottom of the left cavity wall while leaving it through another opening at the right cavity wall. A counter-clockwise rotating plate at the center of the cavity acts as an active flow modulator. Moving mesh approach is used for the rotation of the plate and the numerical solution is achieved using arbitrary Lagrangian-Eulerian finite element formulation with a quadrilateral discretization scheme. Transient parametric simulations have been performed for various frequency of the rotating plate for a fixed Reynolds number (Re) of 100 based on maximum inlet flow velocity while the Richardson number (Ri) is maintained at unity. Heat transfer performance has been evaluated in terms of spatially averaged Nusselt number and time-averaged Nusselt number along the heated wall. Power spectrum analysis in the frequency domain obtained from the fast Fourier transform analysis indicates that thermal frequency and plate frequency start to deviate from each other at higher values of velocity ratio (>4).