新型无灰分散剂的结构分析研究

通过薄膜渗析、红外光谱、凝胶渗透色谱、皂化反应等一系列手段建立了一套对无灰分散剂的系统分析方法，并利用该方法得到了一种新型无灰分散剂及其衍生物的平均结构、相对分子质量分布、分散度等重要结构信息，得出该新型无灰分散剂的结构与传统无灰分散剂的结构不同。     

乘性和加性噪声中谐波恢复的循环统计量方法

本文从循环平衡的观点出发来研究乘性和加性噪声中的谐波恢复问题.首先，在一定条件下建立了一般复过程的有限长付里叶变换的大样本性质．然后，得到了任意阶循环矩的样本估计关于循环频率的一致收敛速度．对于乘性和加性噪声中的谐波信号，建立了一、二、三阶循环矩样本估计的统计性质．在此基础上，分别提出了基于不同阶循环矩的谐波分最个数和频率的估计方法，并得到了估计的强相容性质和强收敛速度，最后给出了模拟实验结果．     

激光加热在Al2O3/Ti系梯度功能材料制备过程中的作用及机理

梯度功能材料是一种界面连续化的新型复合材料,本文研究了激光加热在合成Al2O3/Ti系梯度功能材料过程中的作用和机理,同时用激光大光斑加热方法制备出直径11mm厚度3mm完整的FGM试样并加以分析,以及首次采用在试样中埋设微细热电偶成功地测出了激光加热造成的温度梯度分布。     

Human discrimination of the implicit orientation of simple symmetrical patterns

A hydraulic calcium phosphate cement made of beta-tricalcium phosphate [beta-Ca3(PO4)2], monocalcium phosphate monohydrate [Ca(H2PO4)2-H2O], and water was used as a delivery system for the antibiotic gentamicin sulfate (GS). GS, added as powder or as aqueous solution, was very beneficial to the physicochemical properties of the cement. The setting time increased from 2 to 4.5 min with 3% (w/w) GS and then slowly decreased to 3.75 min with 16% (w/w) GS. The tensile strength increased from 0.4 to 1.6 MPa with 16% (w/w) GS. These effects were attributed to the presence of sulfate ions in GS. The release of GS from the cement was measured in a pH 7.4 phosphate-buffered saline solution at 37 degrees C by USP paddle method. Factors such as cement porosity, GS content and presence of sulfate ions or polymeric additives were investigated. The amount of GS released was roughly proportional to the square root of time up to approximately 50% release. Afterwards, the release rate markedly slowed down to zero. In all but two cement formulations, the total dose of GS was released within 7 days, indicating that no irreversible binding occurred between the cement paste and the antibiotic. When small amounts of hydroxypropylcellulose or poly(acrylic acid) were added to the cement, the maximum fraction released was a few percent lower than the total GS dose, suggesting some binding between the polymer and GS. The GS release rate was strongly influenced by the presence of sulfate ions in the cement paste and by the cement porosity. The higher the sulfate ion content of the cement paste, the lowe the GS release rate. This influence was attributed to the finer cement micro-structure induced by the presence of sulfate ions. Furthermore, when the initial cement porosity was increased from 38 to 69%, the release rate almost tripled (0.16 to 0.45 h-1/2). Finally, the biological activity of GS in the cement was maintained, as measured by assaying the release medium.     

北淮阳金寨-霍山地区火山机构遥感地质解译研究

利用不同时期成像的航卫片资料，圈定和寻找北淮阳金寨－霍山地区火山机构，结合地面验证，研究火山活动的空间展布规律，以及火山机构的成矿控矿作用。     

直缝焊管机组生产冷弯型钢产品初探

主要介绍了φ２１９直缝焊管机组生产高速公路护栏 成型原理、工艺布置、变形方式、变形图和轧辊设计。     

����������Ͳ�¶ȷֲ�����

凝析气井井筒温度分布是进行气井节点分析和动态分析必不可少的参数。根据传热学原理推出了凝析气井井筒温度分布计算公式，研究了温度计算基础数据求取方法，分析了产气量、产水量、井深及油管直径对井口温度的影响规律。对某一井深为５４００ｍ的凝析气井进行了计算，该气井气油比为３０００，含２３％的Ｈ２Ｓ和４％的Ｎ２；地层温度为１３４℃。计算结果表明：井口实测温度与计算温度的相对误差为０２％～３８％，符合工程精度。气井温度随井深不呈线性分布；气井井口温度随产量、井深增加而增加，随油管直径减少而减少；该公式同时适用于干气井、湿气井和凝析气井的温度分布计算，计算精度符合工程精度要求。     

一种铁氧体移相驱动器专用集成电路

介绍了ＳＡ０１８铁氧体移相驱动器专用集成电路的工作原理，电路设计和实验结果。该电路的内部电路设计有双路激励驱动器，放大器，积分器和双路高速比较器等功能单元。将铁氧体移相器的激励驱动器和相位控制器融于一体，大大减少了铁氧体移相器的外围设计。     

用迁移率和载流子浓度研究碲镉汞中的深能级

获得了一种研究碲镉汞深能级的方法。通过分析迁移率 载子浓度与温度的关系，可以得到关于深能级的重要依据。     

提高超小型铝电解电容器生产一次合格率

恰当选择原材料、确保铆接工序质量、重视工作电解液的配比、严控各工序成品率是提高超小型铝电解电容器投入产出一次合格率的关键。以１０Ｖ－４７μＦ（４ｍｍ×７ｍｍ）产品为例，投入产出一次合格率达９４％以上。