Topology design and bridge-capacity assignment for interconnecting token ring LANs: A simulated annealing approach

We address the problem of determining the topology and bridge-capacity assignments for a network connecting a number of token rings via source-routing bridges. The objective is to minimize the cost of bridge installations while meeting the network users' performance requirements. The problem is modeled as a mixed 0–1 integer program. A comparison is given between two solution algorithms: a simulated annealing algorithm using the flow-deviation algorithm for each routing subproblem, and a drop algorithm using the simplex method for the same subproblems to provide benchmark solutions. In the former algorithm, the routing subproblem is formulated as a nonlinear program with penalty functions to model node and link capacity constraints, and in the latter as a multicommodity flow model with the same capacity constraints. Computational results show that the simulated-annealing/flow-deviation algorithm produced substantially better solutions than the LP-based drop algorithm.     

Reduction of loading effect by tungsten etchback in a magneticallyenhanced reactive ion etcher

The plug loading effect occurring during the etchback of tungsten was investigated in a magnetically enhanced reactive ion etcher using SF ₆/Ar mixtures. It was found that while the plug loading effect is independent of varying SF₆/Ar flow rate ratio and magnetic field intensity, it is reduced under the condition of high selectivity of tungsten relative to TiN which was achieved at high chamber pressure and low RF power. It is proposed that when TiN is used as a glue layer, the W etch rate enhancement in the plug is mainly controlled by a local loading effect. Under the optimized etchback conditions the plug loss was successfully controlled without the tungsten residue left on severe topology     

Apoptosis as a cause of death in measles virus-infected cells

To determine the mechanism of measles virus-induced cell death, we studied the infection of Vero cells and monocytic cell lines with wild-type (Chicago-1) and vaccine (Edmonston) strains of measles virus. DNA fragmentation indicative of apoptosis was apparent by flow cytometry, agarose gel electrophoresis, and electron microscopy. Within syncytia, DNA strand breaks were demonstrated by end labeling with terminal transferase and then by visualization.     

Mode analysis of DFB SE lasers

This paper presents theoretical results on mode characteristics of surface-emitting (SE) lasers utilizing an active second-order grating section. Based on a coupled-mode approach, longitudinal modes and the associated space-harmonic transverse modes are calculated via a numerical technique. From these, the lasing-mode spectrum, near- and far-field patterns of the radiation mode, and the surface-emission power efficiency are obtained. Effects of the substrate reflector and the grating parameters are also investigated. Finally, comparisons are made with conventional, edge-emitting DFB lasers. The results indicate that with a suitable choice of structural parameter values, DFB SE lasers can be made to possess both the spectral discrimination of the conventional DFB lasers and the advantages of SE lasers at the same time and also that the second lowest longitudinal mode may be preferred over the fundamental longitudinal mode for many applications due to its symmetric field distribution     

Analysis of culture fluorescence by a fiber-optic sensor inNicotiana tabacum plant cell culture

The on-line sensing of viable cell weight in plant cell culture process is applied to analysis and control of process. The fiber-optic fluorescence sensor was constructed to measure the NADH-dependent fluorescence inNicotiana tabacum plant cell culture and the analysis of fluorescence signal was done to be correlated with the viable cell weight. The structured kinetic model for cell growth was proposed to estimate the theoretical viable cell weight. The dimensional analysis was proposed for the interpretation of fluorescence signal, in which the path length, the inner filter effect and the hydrodynamic conditions were considered as the key factors on fluorescence signal. The dimensional analysis and empirical correlation of fluorescence signal to viable cell weight was applied to the interpretation of the detected fluorescence signal during cultivation. The proposed interpretation of fluorescence signal using dimensional analysis was well correlated with the viable cell weight estimated by the structured kinetic model as well as by empirical correlation.     

Evaluation of Whisker Alignment in Axisymmetric SiCw-Reinforced Al2O3 Composite Material

A quantitative method to evaluate the degree of whisker alignment in axisymmetric composite materials was developed. The angular distribution of the whiskers was analyzed by measuring the aspect ratios of the whiskers observed on a planar section. However, due to the large difference in the probability of whiskers being detected on the planar section (depending on whisker length and degree of alignment), the angular distribution of the whiskers observed on the planar section was significantly different from the actual distributions of the whiskers in three dimensions. Three-dimensional angular distributions were evaluated by comparing the aspect ratios observed on the planar section with those calculated under the assumption that the whisker angle fell in a Gaussian distribution with average angle of 90°. By this method, the degree of preferential alignment is expressed as the standard deviation of the Gaussian distribution. This quantification of whisker alignment is useful in analyzing the mechanical behaviors of composite materials reinforced with elongated particles.     

Einfluß der Korngröße auf mechanische Eigenschaften und den ungeschmierten reversierenden Gleitverschleiß von Al2O3-Keramik

Influence of grain size on mechanical properties and dry oscillating sliding wear of Al₂O₃-ceramics Specimens with average grain sizes varying between about 0.8 μm and 12 μm were produced by cold isostatic pressing of high purity Al₂O₃-powder followed by sintering between 1300°C and 1700°C. Hardness, Young's modulus, bending strength and fracture toughness were measured as a function of average grain sizes. Tribological tests were carried out on the different microstructures at normal laboratory air and room temperature by using a ring-on-block tribometer. Experimental results showed the dependence of mechanical properties on grain size, hardness and bending strength obeying a Hall-Petch type relation, approximately. Coefficient of friction was relatively independent of grain size under the test conditions used. However, wear intensity increased substantially if a critical grain size was surpassed. This was due to a change in mechanisms of material removal which was confirmed by scanning electron microscopical studies of the worn surfaces.     

On detecting the presence of fetal R-wave using the moving averagedmagnitude difference algorithm

An efficient algorithm detecting the presence of a fetal QRS complex is presented. The proposed fetal QRS detection method computes the averaged magnitude of the difference between the fetal ECG signal and the reference signal to detect the fetal QRS event. The detected fetal QRS complexes are exponentially averaged to generate the template signal which can track the slowly varying shape of the fetal ECG signal. As an effort to obtain improved detection performances, two approaches of normalizing the fetal ECG signal and the template are considered.     

Activity of NiO in (Ni,Mg)O Solid Solutions

Disagreement exists in the literature concerting the activity of NiO in (Ni,Mg)O solid solutions. Ideal behavior, as well as strong positive deviations and strong negative deviations from ideality, has been reported. In the present study, the activity of NiO was determined by electromotive force measurements using the solid-state cell Pt/Ni-NiO/0.92ZrO₂-0.08Y₂O₃/Ni-(Ni,Mg)O/Pt. The compositions studied had NiO mole fractions of 0.1,0.3,0.5,0.7, and 0.9. In agreement with theoretical expectations, the solid solutions exhibited ideal behavior at 882° and 982°C. Possible reasons for the conflicting results in the literature arc presented.