Possibilities and extension of XRD material response analysis in failure research for the advanced evaluation of the damage level of Hertzian loaded components

Due to clearly distinguishable damage symptoms, it is differentiated between the surface and sub‐surface failure mode of rolling bearings. Material states red out by X‐ray diffraction (XRD) residual stress measurements point to a variety of loading conditions especially at raceway surfaces that are associated with several competing failure mechanisms. The corresponding lifetime reduction can range from the lower fatigue strength region to material ratcheting in extreme cases. Relevant position of the microstructural changes and nature of the failure mechanisms are characterized. The time alteration of the XRD material parameters measured at or near the surface and at the depth of the maximum equivalent stress correlates, in a different manner, with the statistical parameter of the 10 % bearing life. Both failure modes are illustrated by concrete examples. Contaminated lubricant and boundary lubrication, which represent practically important surface‐induced failures, are discussed in more detail. Gray staining, i.e. shallow pitting, often occurs without distinct indication of global material aging by means of XRD characteristics. Here, scanning electron microscopy observations and electron microprobe analyses point to corrosion fatigue as acting surface failure mechanism. The interaction between material and lubricant under complex loading regimes particularly of mixed friction and corrosion opens further failure research areas in the field of tribology.     

89-GHz fT room-temperature silicon MOSFETs

The authors report the implementation of deep-submicrometer Si MOSFETs that at room temperature have a unity-current-gain cutoff frequency (f_T) of 89 GHz, for a drain-to-source bias of 1.5 V, a gate-to-source bias of 1 V, a gate oxide thickness of 40 Å, and a channel length of 0.15 μm. The fabrication procedure is mostly conventional, except for the e-beam defined gates. The speed performance is achieved through an intrinsic transit time of only 1.8 ps across the active device region     

Synthesis and characterization of poly(siloxane-urethane)s

A series of polyurethane block copolymers based on hydroxy-terminated polydimethylsiloxane and poly(propylene glycol) soft segments of molecular weights 1818 and 2000, respectively, were synthesized. The hard segments consisted of 4,4′-diphenylnethane diisocyanate and 1,4-butanediol as the chain extender. Samples with different molar ratios were prepared. We tried to synthesize polydimethylsiloxane-based polyurethanes (PDMS-PU) containing a hard block as major fraction and a soft block as minor fraction for preparing toughened rigid systems. After a study of the pure polydimethylsiloxane-based polyurethane and poly(propylene glycol)-based polyurethane (PPG-PU), (mixed polyol)-based block copolymers and blends of PDMS-PU and PPG-PU were synthesized, and characterized by means of differential scanning calorimetry, tensile testing and scanning electron microscopy. In (mixed polyol)-based copolymers and lower hard-segment content blends, macro-phase separation occurred, but blends with higher hard-segment contents showed significant reduction in amounts of phase separation.     

Differential K+ channel clustering activity of PSD-95 and SAP97, two related membrane-associated putative guanylate kinases

The molecular mechanisms underlying the clustering and localization of K+ channels in specific microdomains on the neuronal surface are largely unknown. The Shaker subclass of voltage-gated K+ channel alpha-subunits interact through their cytoplasmic C-terminus with a family of membrane-associated putative guanylate kinases, including PSD-95 and SAP97. We show here that heterologous coexpression of either sap97 or PSD-95 with various Shaker-type subunits results in the coclustering of these proteins with the K+ channels. Mutation of the C-terminal sequence (-ETDV) of the Shaker subunit Kv1.4 abolishes its binding to, and prevents its clustering with, SAP97 and PSD-95. Whereas PSD-95 induces plaque-like clusters of K+ channels at the cell surface; however, SAP97 coexpression results in the formation of large round intracellular aggregates into which both SAP97 and the K+ channel proteins are colocalized. The efficiency of surface clustering by PSD-95 varies with different Shaker subunits: striking Kv1.4 clustering occurs in > 60% of cotransfected cells, whereas Kv1.1 and Kv1.2 form convincing clusters with PSD-95 only in approximately 10% of cells.     

Mixing in processing of thermoplastics by extrusion

Translated from Khimicheskoe i Neftyanoe Mashinostroenie, No. 8, pp. 9–11, August, 1993.     

Reduction of loading effect by tungsten etchback in a magneticallyenhanced reactive ion etcher

The plug loading effect occurring during the etchback of tungsten was investigated in a magnetically enhanced reactive ion etcher using SF ₆/Ar mixtures. It was found that while the plug loading effect is independent of varying SF₆/Ar flow rate ratio and magnetic field intensity, it is reduced under the condition of high selectivity of tungsten relative to TiN which was achieved at high chamber pressure and low RF power. It is proposed that when TiN is used as a glue layer, the W etch rate enhancement in the plug is mainly controlled by a local loading effect. Under the optimized etchback conditions the plug loss was successfully controlled without the tungsten residue left on severe topology     

Effect of Forming Pressure on the Internal Structure of Alumina Green Bodies Examined with Immersion Liquid Technique

Green bodies prepared by compaction of alumina granules were made transparent by an immersion liquid technique, and the internal structure was characterized with an optical microscope to study the effect of forming pressure on the internal structure. Clear images obtained by the technique provide more detailed information than other existing methods for structures ranging from one to tens of micrometers. Intergranular pores were present between unfractured granules. Their sizes and concentration tended to decrease with increasing forming pressure. However, pores were clearly present even in the green body prepared at 600 MPa. A rod- and needlelike feature was also found and was concluded to correspond to a high-density region. The significance of large pores and high-density regions on processing as well as the details of the technique is discussed.     

Production and properties of micro‐porous glas bubble zinc and aluminium composites

Micro‐porous syntactic foams were produced by means of integration of glass bubbles into aluminium and zinc matrices. Preforms of glass bubbles were pressure infiltrated with the alloys AlSi9Cu9 ans ZnAl4Cu using squeeze casting. The preforms were sintered thermically without the use of bonding agents. Using the combination of different sintering steps syntactic foams with locally different densities could be produced. The mechanical properties of the foams were tested indicating a high compression strength of the foams and a very good compression energy absorption. Furthermore, corrosion behaviour and behaviour at higher temperatures were investigated.     

The prospects of non-volatile phase-change RAM

Phase-change read-and-write memory (PRAM) is a promising memory that can solve the problems of conventional memory—scalability, read/write speed, and reliability. We will review the opportunities and technical challenges of PRAM. The most important challenge of PRAM is the reduction of the writing current. Various approaches to reduce the writing current will be reviewed and the prospects of PRAM are discussed.