Low cycle fatigue and creep behavior of recrystallized Molybdenum near room termperature

The deformation behavior of pure recrystallized molybdenum under cyclic and static loads was investigated in the temperature range between 30°C and 10O°C, for stress amplitudes between 100 MPa and 250 MPa and for static loads up to 200 MPa. The results show that in spite of the low test temperatures and stress levels the Mo material exhibits considerable plastic strains which depend sensitively on frequenez and small changes in temperature.The activation energy deduced for the static and dynamic deformation is less than 0.98 eV which indicates thermally activated processes, to be explained by a dislocation kink model as described in the literature. The low-temperature fatigue behavior appears strongly influenced by creep-fatigue interaction phenomena.     

Observation of atomic steps on CaCO3 crystal surface

By using scanning polarization force microscopy,the deliquescence process and the atomic steps on the cleavage surface of CaCO3 in air were studied in situ.Under an exposure to medium umidity(-57%),the sloiw step movement has been observed.     

Reduction of loading effect by tungsten etchback in a magneticallyenhanced reactive ion etcher

The plug loading effect occurring during the etchback of tungsten was investigated in a magnetically enhanced reactive ion etcher using SF ₆/Ar mixtures. It was found that while the plug loading effect is independent of varying SF₆/Ar flow rate ratio and magnetic field intensity, it is reduced under the condition of high selectivity of tungsten relative to TiN which was achieved at high chamber pressure and low RF power. It is proposed that when TiN is used as a glue layer, the W etch rate enhancement in the plug is mainly controlled by a local loading effect. Under the optimized etchback conditions the plug loss was successfully controlled without the tungsten residue left on severe topology     

Si/SiGe epitaxial-base transistors. I. Materials, physics, andcircuits

A detailed review of SiGe epitaxial base technology is presented, which chronicles the progression of research from materials deposition through device and integration demonstrations, culminating in the first SiGe integrated circuit application. In part I of this paper, the requirements and processes for high-quality SiGe film preparation are discussed, with emphasis on fundamental principles. A detailed overview of SiGe HBT device design and implications for circuit applications is then presented     

Einfluß der Korngröße auf mechanische Eigenschaften und den ungeschmierten reversierenden Gleitverschleiß von Al2O3-Keramik

Influence of grain size on mechanical properties and dry oscillating sliding wear of Al₂O₃-ceramics Specimens with average grain sizes varying between about 0.8 μm and 12 μm were produced by cold isostatic pressing of high purity Al₂O₃-powder followed by sintering between 1300°C and 1700°C. Hardness, Young's modulus, bending strength and fracture toughness were measured as a function of average grain sizes. Tribological tests were carried out on the different microstructures at normal laboratory air and room temperature by using a ring-on-block tribometer. Experimental results showed the dependence of mechanical properties on grain size, hardness and bending strength obeying a Hall-Petch type relation, approximately. Coefficient of friction was relatively independent of grain size under the test conditions used. However, wear intensity increased substantially if a critical grain size was surpassed. This was due to a change in mechanisms of material removal which was confirmed by scanning electron microscopical studies of the worn surfaces.     

Highly compact AC-AC converter achieving a high voltage transferratio

This paper reports a new, highly integrated modular design approach for pulsewidth-modulation AC-AC converters based on a modular phase-bank structure. Novel high-power 3-in-1 integrated bi-directional power modules (IBPM) rated at 1200-V AC and 150 A and the 3-to-1 phase bank circuits have been successfully developed, fabricated and tested. This enables the modularity design of the multiphase converter systems and reduces the critical parasitic inductance. A theoretical analysis of the IBPM's silicon utilization for this new breed of direct power converters has been outlined. A lab prototype at medium power level has been successfully designed, implemented, and tested with good results. A nearly 460-VRMS out voltage at a 1:0.955 voltage transfer ratio, which, perhaps, is the highest performance reported so far in the literature, has been achieved by the novel two-side modulation control system. The converter-fed AC motor system is able to operate over the 0-240 Hz range with inherent regenerative capability and four-quadrant operation. Potential industrial applications are also briefly highlighted in this paper     

The design of experiments when there are errors in all the variables

The Error-in-Variables Model (EVM) applies to a large class of problems in parameter estimation in which there is error in all the variables. This property makes it of more general applicability than the widely used technique of ordinary Least Squares. While there is a voluminous literature on EVM there is nothing on a general method for designing experiments when EVM applies. In this paper we present an extension of the concept of D-optimality to provide such a general method. It is illustrated by applying it to the estimation of copolymer reactivity ratios and to fitting an ellipse.     

含氟聚酰亚胺的辐射交联及其交联度的XPS表征

含氟聚酰亚胺(FPI)是一种耐高温、耐水解的新型聚酰亚胺。到目前为止,尚未见文献报道它的辐射交联。本文发现它能在高温辐射下交联,交联后的含氟聚酰亚胺的玻璃化转变温度以及高温力学性能有明显提高。本文还首次用XPS方法做了它的交联度表征。用XPS方法求得FPI的凝胶化剂量为50Mrad。     

Possibility of sewage and combined sewer overflow reuse with biological aerated filters.

The secondary effluent from municipal plants in Korea generally represents higher BOD with lower SS. Therefore, more soluble forms of organics and NH4-N need to be removed to improve its effluent for reuse. In this study reuse possibility of secondary effluent and CSO (combined sewer overflow) using BAF (biological aerated filter) was evaluated. The tertiary application with 1.2 h EBCT, SS, BOD and COD showed stable concentrations less than 1.3, 1.3 and 6.2 mg/L, respectively. Nitrogen could be nitrified even at 7 degrees suggesting BAF can be used for a water reuse method as well as an effective add-on facility in cold regions. However, BAF was not stable with CSO application at increased flow rates suggesting CSO must be equalised prior to application. Disinfection was necessary even during normal weather conditions.