汽化冷却技术在加热炉支撑梁上的应用

介绍了汽化冷却技术在加热炉支撑梁上的应用,在生产实践中该技术获得了良好收益,节约了能源,在同类钢铁企业中可广泛应用。     

五元精炼渣系熔化温度的研究

利用正交实验的方法对CaO-Al₂O₃-SiO₂-MgO-CaF₂精炼渣的熔点进行了研究。经过方差分析和显著性检验,得出该五元精炼渣系的最佳组成为:25%Al₂O₃、12%CaF₂、7%MgO、R2(CaO/SiO₂)=2.5。并用SPSS软件回归出了可信度高的组分与精炼渣熔化温度之间的数学关系式:T_m=1 451.3-6.25CaF₂-7.36R₂。     

850kW风力发电机设备安装技术

介绍了850kW风力发电机设备安装工艺流程以及吊装机械的选择方法。对塔筒、机舱、叶轮等主要设备的安装顺序、方法、要点及其注意事项,均进行了详细叙述。     

基于一般访问结构的多重秘密共享方案

基于Shamir的门限方案和RSA密码体制，提出一个一般访问结构上的秘密共享方案．参与者的秘密份额是由各参与者自己选择，秘密分发者不需要向各参与者传送任何秘密信息．当秘密更新、访问结构改变或参与者加入／退出系统时，各参与者的份额不需要更新．秘密份额的长度小于或等于秘密的长度．每个参与者只需维护一个秘密份额就可以实现对多个秘密的共享．在秘密恢复过程中，每个参与者能够验证其他参与者是否进行了欺骗．方案的安全性是基于Shamir的门限方案和RSA密码体制的安全性．     

磁控溅射CuCrMo薄膜耐126kV 20kA电弧烧蚀性能

提升真空断路器CuCr触头的抗电弧烧蚀能力是决定其能否应用于高压真空灭弧室的核心关键,尚未见有效触头材料或表面涂层改性技术使CuCr触头应用于126kV以上真空灭弧室的报道。基于CuCrMo薄膜的优异电气性能,对沉积CuCrMo薄膜的真空灭弧室触头进行126kV下的抗电弧烧蚀研究,并进行开断寿命的工程验证。采用磁控溅射技术在CuCr50真空触头片表面沉积5μm厚的CuCrMo薄膜,对其进行126kV 20kA电流下23次的电寿命试验。利用XRD、SEM和3D共聚焦显微镜研究电弧烧蚀后表面形貌。研究结果表明：沉积CuCrMo薄膜的触头片,在纵向磁场和126kV 20kA条件下可有效分散电弧,较未镀膜触头片有更小电弧电流密度;经过23次电寿命试验后,表面烧蚀程度比未镀膜的触头片轻,表面粗糙度降低,提高了触头的开断寿命。为表面改性真空断路器CuCr触头在高电压大电流真空灭弧室的应用提供了有效工程依据。     

Investigation of microstructure and mechanical properties of multi-layer Cr/Cr2O3 coatings

Single and multi-layer Cr/Cr₂O₃ coatings were deposited by reactive magnetron sputtering with the total thickness of 7 μm on steel substrates. X-ray diffraction analysis showed that single and multi-layer Cr/Cr₂O₃ coatings have different preferred crystal orientations. Columnar microstructure was detected by transmission electron microscopy both in metal chromium and ceramic chromium oxide layers. Grain size increased with the coating thickness. The value of single and multi-layer coating's fracture toughness is between 4 and 6 MPa·m^1/2 measured with the Berkovich tip indentation, and it is between 2.8 and 3.9 MPa·m^1/2 when measured with the Vickers indenter. The adhesion is about 192.1 and 246.7 J/m² for single and multi-layer coatings, respectively.     

A prediction method for fatigue life of large moving components as function of scale factor: A case of motor‐generator rotor

With the development of science and technology, more and more large moving components have been used in industry, and their service lives have become an important issue. After analysis of the previous results, considering the scale factor, a prediction method for fatigue life of large moving components based on the Basquin relation was proposed at first, and then the magnet pole part of motor‐generator rotor was chosen to make simulation parts with different scale factors mainly in terms of their S‐N curves and fractographies. It was found that with the change of specimen scale factor, the stress concentration factor at transition arc is almost unchanged as well as the fatigue strength exponent, and the fatigue strength coefficient changes linearly. Based on those results, a life prediction method was validated, and the results show that this method is a simple but more precise relation. After fatigue fracture surface and crack growth angle observations and quantitative analyses, the fatigue damage mechanisms associated with the relation among fatigue strength exponent and coefficient and scale factors were explained well. Those studies will provide a new clue to the prediction of the service life for those large moving components.     

武器维修器材包装系列研究(1):研究情况概述

介绍武器维修器材包装系列研究的主要技术成果。该成果运用系统工程原理,从整个器材流通过程出发,通过全面、深入的研究,使器材包装融生产、运输、储存、管理、供应、使用为一体,为器材包装的通用化、系列化、标准化奠定了基础。     

储油缸塑件圆周抽芯注射模设计

分析了储油缸的塑件工艺特点,主要分析了点浇口注射模成型且带侧向抽芯机构制品的工艺特点．介绍了带转盘的注射模结构,为保证外观质量,综合地处理好产品外观要求与浇口位置及脱模方式之间的问题,简化模具结构,减低制造成本,提高了生产效率。