All-spray-coated semitransparent inverted organic solar cells: From electron selective to anode layers

We demonstrated an all-solution-processed electron selective layer, active layer and top electrode for large-area inverted organic solar cells. The fabricated devices are semitransparent, fully spray-coated, highly efficient and air-stable, with power efficiencies of 2.41% and 1.0% for cell areas of 0.36 and 15.25 cm², respectively. The shelf life of the cells in air is demonstrated by the ∼80% retention of original cell efficiency after 30 days.     

1‐Arylsulfonyl‐5‐(N‐hydroxyacrylamide)indolines Histone Deacetylase Inhibitors Are Potent Cytokine Release Suppressors

A series of 1‐arylsulfonyl‐5‐(N‐hydroxyacrylamide)indolines ( 7 – 15 ) has been developed; the compounds exhibited potent histone deacetylase (HDAC) inhibitory activities. Notably, almost all of this series exhibited better HDAC‐inhibitory and antiproliferative activities than 3‐(1‐benzenesulfonyl‐1H‐indol‐5‐yl)‐N‐hydroxyacrylamide ( 6 ), as reported in a previous study. Among these compounds, 3‐[1‐(4‐methoxybenzenesulfonyl)‐2,3‐dihydro‐1H‐indol‐5‐yl]‐N‐hydroxyacrylamide ( 9 ) showed a two‐ to tenfold increase in activity compared to SAHA ( 1 ) in the suppression of lipopolysaccharide‐induced cytokine production. Compound 9 also caused a marked reduction in carrageenan‐induced acute inflammation in a rat model. Taken together, these data indicated that 1‐arylsulfonyl‐5‐(N‐hydroxyacrylamide)indolines HDAC inhibitors exhibit potent anti‐inflammatory activity.     

Characterization of Aerosol Surface Instruments in Transition Regime

The primary purpose of this study is to measure the size- and composition-dependent responses of aerosol surface instruments designed to measure surface area related properties. Measurements were conducted in the range of 30–150 nm of mobility equivalent diameter, D_p. The responses of a LQ1-DC (a diffusion charger manufactured by Matter Engineering AG) and an EAD (a diffusion charger manufactured by TSI) to singlets (NaCl) particles are proportional to D_p ^1.36 and D_p ^1.13, respectively. The response of LQ1-DC agrees with Fuchs surface area, which is proportional to D_p ^1.39 within 2.4% error. The response of the EAD is almost proportional to diameter, D_p. A PAS2000CE (Photoelectric Aerosol Sensor manufactured by EcoChem) gave both size and composition-dependent responses. For diesel particles produced at high engine loads, the response was nearly proportional to Fuchs surface area. However, at lighter engine loads, the response dropped sharply with decreasing D_p. Light engine loads are associated with high fractions of volatile particles that may suppress the photoemission response. The secondary purpose of this study is to investigate the difference in charging rate between singlets (NaCl particles) and agglomerates (diesel particles) by using diffusion chargers. Agglomerates (diesel particles at engine load 75%) acquire more charge than singlets (NaCl particles) by 15 and 17% for LQ1-DC and EAD, respectively.     

Piezoresistive effects of copper-filled polydimethylsiloxane composites near critical pressure

Piezoresistive properties of polydimethylsiloxane (PDMS) filled with copper particles in volume fraction above the electrical percolation threshold (25.3–50.7 vol%) were investigated. Piezoresistive behavior of the PDMS-copper composites under compressive pressure showed not only a change in resistance by approximately six orders of magnitude (∼1.5 MPa), but also a change in the critical pressure due to variations in the hardness of the composites. Resistivity relaxation was observed near the critical pressure and was explained through a stress relaxation and percolation mechanism. The mean tunneling distance was calculated by using a theoretical equation for percolation under compression. When the gauge factors of the composites were plotted versus strain, a universal curve was obtained regardless of the copper contents. Finally, the PDMS-copper composite demonstrated good repeatability, showing only small differences in the relative resistance after five successive tests.     

Fabrication of Fe-Al nanoparticles by selective oxidation of Fe-Al thin films

The possibility of a new technique for fabricating nanoparticles from thin films using selective oxidation in an atmosphere mixture of water vapor and hydrogen was investigated. Fe-5wt.%Al films were RF-sputtered and annealed in the atmosphere mixture at 900°C for up to 200 min, in order to oxidize aluminum selectively. Thermodynamics simulation showed that temperatures exceeding 800°C are necessary to prevent iron from being oxidized, as confirmed by the depth profile of XPS. As the annealing time increased, the morphology of the 200-nm Fe-Al films changed from the continuous to the discontinuous type; thus, particulate Fe-Al films formed after 100 min. The particulate 10- to 100-nm Fe-Al films showed super-paramagnetic behavior after the oxidation. Thus, a new technique for fabricating nanoparticles was successfully introduced using selective oxidation.