Rubber‐toughened polyamide‐6 with a low thermal expansion coefficient: effect of preferential distribution of rubber and inorganic filler

The effects of morphological changes on the thermal expansion, toughness and heat resistance of polyamide‐6 (PA)/styrene–ethylene–butylene–styrene (SEBS)/polyphenylene ether (PPE) blends were investigated. Compared with the typical ‘sea (PA matrix)–island (PPE domain)–lake (SEBS in PPE domain)’ morphology, an injection‐molded ternary blend with a preferential distribution of SEBS component at the interface between PA and PPE exhibited a low coefficient of linear thermal expansion (CLTE) in the flow direction. This low CLTE was ascribed to the deformation of SEBS and PA into a co‐continuous microlayer network structure during injection molding. Consequently, the expansion preferentially occurred towards the thickness direction. Further CLTE reduction either by a change in PA viscosity or by the selective location of an inorganic filler was examined, and its influences on impact strength and heat resistance are discussed based on transmission electron microscopy observations. © 2015 Society of Chemical Industry     

A mass separation of chondrocytes from cartilage tissue utilizing an automatic crushing device

Porcine articular cartilage tissue was crushed using Multi-Beads-Shocker^™ and digested with trypsin and collagenase type II. Chondrocyte cell yield was maximized by automatic crushing for 10 s, which was 4 times that by manual dicing with a surgical blade and might be useful for the automation of the cell processing.     

Deposition of DLC film with adhesive W-DLC layer on stainless steel and its tribological properties

Tribological properties of a diamond-like carbon (DLC) coating with an adhesive tungsten-containing DLC (W-DLC) layer were investigated. The coatings were deposited onto AISI316L steel substrates and Si wafers using plasma enhanced chemical vapor deposition and tungsten co-sputtering of the metal target. Methane and argon gases were used as the precursor of the coatings. In this study, three types of coatings were evaluated: DLC/W-DLC on AISI316L (DLC-1), DLC/W-DLC on Si wafer (DLC-2), and DLC on Si wafer (DLC-3). The structural characterizations were performed by transmission electron microscopy and tapping mode atomic force microscopy. At the boundary between the W-DLC layer and the AISI316L substrate, microscopic decohesion or delamination was not observed. The surface roughness of the DLC-1 coating was greater than that of the DLC-2 coating. This feature was derived from the surface roughness of the initial surface of the AISI316L substrate. Friction tests were performed using a rotation-type ball-on-flat configuration tribometer. The observed friction of the DLC-1 coating was unstable compared with the DLC-2 or DLC-3 coatings. This was due to wear debris which had risen to the friction surface resulting in unstable friction on the DLC-1 coating. During the friction studies, the top DLC layer was removed from the adhesive W-DLC layer because the adhesive strength at this part was not enough. In order to achieve the low and stable friction of the DLC coating with the W-DLC layer on AISI316L, it is necessary to improve the smoothness of the surface and the adhesion between the DLC coating and the W-DLC layer.     

Evaluating a behavioral demand response trial in Japan: evidence from the summer of 2013

This paper presents results from a behavioral demand response trial targeted to both grid and residential peak hours, in which weekly feedback via paper-based reports, real-time feedback via an in-home display, 30-minute tiered rate, and email prompts are adopted to almost 230 residential customers of a condominium in Funabashi, a city located in Greater Tokyo. Through a randomized experiment, we find that the peak saving impact during grid peak hours (1–4 pm, weekdays only) was 11.6 %, given that all the four interventions provided all at once. In addition, the results show that the variation in peak saving effects by household characteristics exists, and the variation differs among packages of peak saving interventions. Furthermore, we analyzed how much informational elements in weekly reports are considered as useful by residential customers. These results suggest that feedback-based approaches for peak saving can promote households’ energy conservation behavior.     

Effect of Oxide Film on the Friction of 52100 Steel in Vacuum

To solve the anomalous behaviors of friction coefficient in reciprocated slidings of 52100 steel in ultrahigh vacuum, studies were made if the wear track, friction level, and number of traverses for a 52100 steel test ball sliding on a 52100 steel flat over a pressure range of 760 to 3 × 10^?9 torr. Plots of the friction coefficient versus number of traverses show a maximum (f = 1.0–1.2) followed by a drop (f = 0.5–0.6). Both the friction force-time curves and microscopic friction area change from smooth to rough at the point of the drop in friction coefficient. The shape of the friction plot is ascribed to a build-up and rupture of the oxide film that forms on the surface of the 52100 steel specimen in atmosphere and is affected by applied load, direction of finishing marks and pressure level of the environment. Further, above a critical pressure of 10^?6 torr the drop was not experienced. It was also found that higher friction does not always mean that the sliding surfaces are clear or more oxide-free.     

Decay of material properties of degraded MEA caused by repeated cold starts under subzero conditions in polymer electrolyte fuel cells

This study investigated the characteristics of cell performance degradation, decline of component performance, and changes in the properties of membrane electrode assembly materials caused by repeated cold starts under a subzero condition of ?30 °C. It was made clear that functional decay appeared mainly at the cathode due to increased proton conductive impedance and reduction of reactivity of the electrode catalyst. Among the cathode components, an increase in proton conductive impedance in the cathode electrolyte was dominant. Furthermore, the application of ion chromatography and a newly developed proton‐induced gamma‐ray emission method to measure fluorine in the off‐gas drain revealed that decomposition of the electrolyte was dominant in the cathode catalyst layer. A decrease in fluorine in the cathode electrolyte measured by fluorine‐19 nuclear magnetic resonance confirmed this decomposition. A hypothesis is also presented concerning the cause of the performance degradation. © 2012 Wiley Periodicals, Inc. Heat Trans Asian Res; Published online in Wiley Online Library ( wileyonlinelibrary.com/journal/htj ). DOI 10.1002/htj.20394     

Layered mixed-anion compounds: Epitaxial growth,active function exploration,and device application

Optoelectronic properties and device applications of layered mixed-anion compounds such as oxychalcogenide LaCuOCh (Ch = chalcogen) and oxypnictide LaT_MOPn (T_M = 3d transition metal, Pn = pnicogen) are reviewed. Several distinctive functions have been found in these materials based on our original material exploration concept. Fabrication of high-quality epitaxial films of LaCuOCh leads to clarifying the excellent electrical and optical properties such as high hole mobility of 8 cm²/(V s) and heavy hole doping at >10²¹ cm^?3 in LaCuOSe, and sharp and tunable-wavelength photoluminescence in the solid–solution systems in LaCuOCh. In addition, a room temperature operation of a light-emitting diode is demonstrated using LaCuOSe as a light-emitting layer. These results suggest that the layered oxychalcogenides have potential for light-emitting layers as well as transparent hole-injection layers in organic/inorganic light-emitting diodes. Furthermore, by extending the material system from the copper-based oxychalcogenides to isostructural compounds, transition metal-based oxypnictides LaT_MOP (T_M = Fe, Ni), we have found novel superconductors, LaFeOP and LaNiOP.     

Market micro-structure analysis by multiagent simulation in X-Economy -- comparison among technical indices

We are developing an agent and server library referred to as X-Economy, by which we can execute multiagent simulations and network games for financial and economic systems. To this end, we analyzed the characteristics of network games in a financial context and compared them with traditional ones. X-Economy has also provided a new research direction in market micro-structure analysis. We executed several kinds of multiagent simulations for technical traders (indices) and obtained non-trivial suggestions regarding the relationship between the market randomness and the effectiveness of technical indices. For instance, the performance of complex technical indices seemed to deeply depend on the characteristics and nature of a market when a market became complex, i.e. it moved far from the Wiener process.     

PID landing orbit motion controller for an indoor blimp robot

Blimp robots are attractive as indoor flying robots because they can float in the air, land safely with low energy, and stay in motion for a long time compared with other flying robots. However, controlling blimp robots is difficult because they have nonlinear characteristics, are influenced by air streams, and can easily be influenced by inertia. Therefore, a robust and adaptive control system is needed for blimp robots. The applied research that has studied the features of indoor flying robots in recent years has prospered. Operating an indoor blimp robot for a long time is difficult because the payload is small, multiple batteries cannot be stacked, and the design of a thruster that gives freedom to the entire blimp robot is difficult. Therefore, an autonomous charge that allows operation for a long time is needed. We have developed a method of landing with orbital control of the charge point that gives autonomy to a blimp robot. The possibility of landing with orbital control is shown. This work was presented in part at the 10th International Symposium on Artificial Life and Robotics, Oita, Japan, February 4–6, 2005 An erratum to this article is available at .