Development of fabrication process for Ag/polydiacetylene (core/shell) hybridized nanocrystals

Core/shell hybridized nanocrystals composed of Ag nanoparticle core and polydiacetylene shell were fabricated successfully by means of “co-reprecipitation/microwave irradiation method”. The hybridized nanocrystals were characterized using transmission electron microscopy (TEM) observation and UV–vis absorption spectroscopy. UV–vis spectral measurements revealed that polydiacetylene shell was the red phase while π-conjugated backbone is distorted. Detailed mechanism of formation of the red phase was discussed.     

New type of pressurized cultivation method providing oxygen for piezotolerant yeast

For efficient oxygen supply to pressurized culture, we developed a method using a highly pressurized membrane reactor with an air-saturated medium circulation system. The new method increased the cell growth of aerobic yeast approximately 20 folds larger than that in the case of using a conventional method.     

A Monolayer MoS2 FET with an EOT of 1.1 nm Achieved by the Direct Formation of a High-κ Er2O3 Insulator Through Thermal Evaporation

Achieving the direct growth of an ultrathin gate insulator with high uniformity and high quality on monolayer transition metal dichalcogenides (TMDCs) remains a challenge due to the chemically inert surface of TMDCs. Although the main solution for this challenge is utilizing buffer layers before oxide is deposited on the atomic layer, this method drastically degrades the total capacitance of the gate stack. In this work, we constructed a novel direct high-κ Er₂O₃ deposition system based on thermal evaporation in a differential-pressure-type chamber. A uniform Er₂O₃ layer with an equivalent oxide thickness of 1.1 nm was achieved as the gate insulator for top-gated MoS₂ field-effect transistors (FETs). The top gate Er₂O₃ insulator without the buffer layer on MoS₂ exhibited a high dielectric constant that reached 18.0, which is comparable to that of bulk Er₂O₃ and is the highest among thin insulators (< 10 nm) on TMDCs to date. Furthermore, the Er₂O₃/MoS₂ interface (D_it ≈ 6 × 10¹¹ cm⁻² eV⁻¹) is confirmed to be clean and is comparable with that of the h-BN/MoS₂ heterostructure. These results prove that high-quality dielectric properties with retained interface quality can be achieved by this novel deposition technique, facilitating the future development of 2D electronics.     

Microstructural degradation mechanisms during creep in strength enhanced high Cr ferritic steels and their evaluation by hardness measurement

There are two creep regions with different creep characteristics: short-term creep region “H”, where precipitates and subgrains are thermally stable, and long-term creep region “L”, where thermal coarsening of precipitates and subgrains appear. In region “H”, the normalized subgrain size (λ-λ₀)/(λ^∗-λ₀) has a linear relation with creep strain and its slope is 10ε⁻¹. But, region L is the time range in which the static recovery and the strain-induced recovery progress simultaneously. In this region, the static recovery accelerates the strain-induced recovery, and subgrain size is larger than that line which neglects the contribution of the static recovery. In region “L”, the Δλ/Δλ^∗-strain present a linear relation with a slope 35ε⁻¹. There is a linear relation between hardness and subgrain size. Hardness drop, H₀ − H, as a function of Larson-Miller parameter can be a good measure method for assessment of hardness drop and consequently degradation of microstructure. Hardness drop shows an identical slope in creep region “H”, whereas hardness drop due to thermal aging and creep in region “L” show together a similar slope. In region “H”, degradation of microstructure is mainly due to recovery of subgrains controlled by creep plastic deformation, and precipitates do not have a major role. However, in creep region “L”, there are three degradation mechanisms that accelerate creep failure; (1) strain-induced recovery of subgrains due to creep plastic deformation, (2) static-recovery of subgrains and precipitates and (3) strain-induced coarsening of precipitates due to the appearance of static-recovery.     

Development of a new X-ray source using backscattered X-ray with the use of a cold cathode

The development of an intense X-ray source using backscattered X-ray produced using an advanced electrode configuration is described. The electrodes were composed of field emitters deposited on a wire mounted on a perforated plate as the cathode and a copper plate as the anode. Electrons from these emitters collided with the copper plate and X-ray was generated at collision points. The backscattered X-ray in the direction normal to the electron trajectory through a hole in the anode escaped from the vacuum chamber through a beryllium window. Continuous and characteristic X-rays were detected at an applied voltage lower than that of a conventional X-ray source from 3.0 to 9.4 kV, respectively. Moreover, the X-ray dosage measured with a survey meter reached 0.95 mSv/h at 5.0 kV of applied voltage. The transmission images of three types of material used as an X-ray source for the X-ray imaging system indicate three advantages; low power consumption, focal point controllable by adjusting applied voltage, and photographable motion picture of X-ray transmission.     

A simple mass and heat balance model for estimating plant conditions during the Fukushima Dai-ichi NPP accident

A simple evaluation method for the analysis of thermal-hydraulic transients in reactor pressure vessel (RPV) and primary containment vessel (PCV) is proposed to support understanding the accident behaviors of the Fukushima Dai-ichi nuclear power plant (NPP). Since most of the measurements of the plants were unavailable especially in the early stage of the accident, and the accessibility to the plants had been limited by radiation, analytical investigation for the plant was required to understand the plant conditions such as the magnitude of the damages. In order to provide easy-to-use technical tools to support the analytical investigation, we developed a simplified analysis code, named “HOTCB”, based on total mass and heat balances in a lamped parameter system. The HOTCB code has capabilities to treat two-phase fluid including water, steam, and non-condensable gas in a wide range of temperatures up to highly superheated conditions, and to consider heat structures, i.e. heat capacities and heat transfer to the fluid. The code was provided to Tokyo Electric Power Company (TEPCO) and was practically used for the analysis on the accident. This paper provides the details of the code and simulations of Unit 1 and Unit 2 reactors of Fukushima Dai-ichi nuclear power plant (NPP) as examples to show the usefulness of the code.     

Measurement of the isotopic abundance of boron-10 by inductively coupled plasma-quadrupole mass spectrometry

This article describes the method for measuring the isotopic abundance of ¹⁰B in nuclear grade boron carbide using inductively coupled plasma-quadrupole mass spectrometry (ICP-QMS). The results of investigation revealed that both the integration time and the dwell time have a major influence on the reproducibility of ICP-QMS measurements. As a result of optimization of the measurement conditions, reproducibility below 0.2% relative standard deviation (RSD) (0.17% RSD maximum) was achieved. In addition, the measured value of the isotopic abundance of ¹⁰B for each sample well agreed with the values measured by the TIMS. Thus, the method described in the present investigation was very effective in the analysis of isotopic abundance of ¹⁰B in B₄C or H₃BO₃. The results of this study suggest that ICP-QMS could be applied to the precise analysis of the isotopic abundance of ¹⁰B required in the field of nuclear applications.     

Response function estimation with fine energy bins for the energy-resolved computed tomography using a transXend detector

A new ‘transXend’ detector system has been developed for energy-resolved computed tomography (CT). It consists of several segmented detectors that measure X-rays as electric currents. Response functions of segmented detectors are estimated using component materials of a body under inspection to unfold X-ray spectra. To avoid material-dependent measurements, response functions inherent to segmented detectors are evaluated by Monte Carlo calculations. CT was performed for a phantom consisting of five resins and was analyzed by the estimated response functions. The linear attenuation coefficients for the five resins have excellent agreement with database values.