Anomalous quantum transport through a thin film of varying impurity density with the distance from the film surface

We explore a novel transport phenomenon by studying the effect of disorder on electron transport through a thin film of varying disorder strength with the distance from its surface. A simple tight-binding model is used to describe the film which is attached to two metallic electrodes, where the coupling of this film to the electrodes is treated through the use of Newns-Anderson chemisorption theory. It is found that, in the strong disorder regime the current amplitude through the film increases with the increase of the disorder strength, while it decreases in the weak disorder regime. This strange behavior is completely opposite to that of a conventional disordered system. Our results also predict that the electron transport is significantly influenced by the finite size of the thin film.     

A scheme for finite element analysis of mode I and mixed mode stable crack growth and a case study with AISI 4340 steel

A new scheme for elastic–plastic finite element analysis has been proposed for the study of stable crack growth (SCG) from initiation to instability in both mode I and mixed modes (I and II). The scheme is based on node-release technique and helps to determine the variation of fracture load with crack extension without requiring much computer storage and time. The scheme permits predictions of load variation with load line displacement (LLD), maximum fracture load, crack tip current plastic zone and crack edge profile. In the analysis the condition for crack extension at every stage of the SCG is considered to be governed by CTOA/COD reaching a critical value. The scheme of analysis is different from the ones proposed by earlier investigators. The whole SCG is analysed in a few stages using the ANSYS software and a single discretization. Element arrangement in the discretization is decided from the very beginning; it has a capability of accommodating changes in boundary conditions arising out of crack extension in the later stages. Each stage is analysed afresh ignoring state of stress–strain reached at a material point at the end of the previous stage. Case studies on both mode I and mixed mode presented considering AISI 4340 steel, which is widely used in nuclear power industry, indicate that the SCG through it can be characterized in terms of a single COD or CTOA. Predictions for the initiation and maximum fracture loads in both the cases compare very closely with the experimental data reported. The results presented also include the value of critical COD/CTOA (0.035 mm/0.0875 rad) characterizing the SCG through the steel and show that the initiation load is not significantly affected by crack tip radius up to 0.05 mm.     

Effect of Active Raw Material Variability on Tablet Production: Physicochemical, Physiocomechanical and Pilot Plant Studies

Batch-to-batch variation in an active raw material was evaluated following a production process change by the raw material supplier. Physicochemical and physicomechanical tests were applied and indicated that polymorphism or solvate formation was not occurring but changes in crystal properties in terms of size and degree of aggregation were involved. Other more subtle differences in crystal properties were also possible

The deleterious effect of the raw material process change on tablet production was noted and a method of overcoming the problem identified

The necessity for comprehensive? reformulation studies including physicomechanical screening is underlined. Such studies are also necessary if changes in raw material production methods occur to avoid process problems related to the marked hatch-to-batch variation that can occur in these instances     

Studies on the influence of lanthanum oxide on the sinterability of chromium(III) oxide

The mechanism of sintering in chromium(III) oxide in the presence of varying amounts of lanthanum oxide under firing conditions which simulate a controlled reducing atmosphere, has been investigated. The investigation is based on isothermal shrinkage measurements at different temperatures. The data suggest that the vapour-phase transport mechanism becomes predominant with evidence of a grain-boundary diffusion process.     

Carbon nanohorn‐graphene nanoplate hybrid: An excellent electrode material for supercapacitor application

This study describes the capacitor behavior of carbon nanohorn (CNH)/graphene nanoplate (GNP) hybrid (CNGN). The well‐CNH‐decorated GNP‐plate electrode materials show high capacitance value (≈677 F/g) and can be extensively used in new generation for energy storage. In the hybrid (CNGN), two nanofillers jointly affect the capacitance behavior and increase the capacitance value of the CNGN hybrid. Homogeneous coating of CNH over the GNP plate plays an effective role to enhance the capacitance behavior of the composite. Field emission scanning electron microscopy and high‐resolution transmission electron microscopy analysis of the composite confirmed the CNH coating on the GNP plate. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 42118.     

Effect of Alumina Reactivity on the Densification and Properties of Al2O3–Cr2O3 Refractories

Alumina‐chrome (Al₂O₃–Cr₂O₃) refractories with Al₂O₃:Cr₂O₃ molar ratio 1:1 were synthesized in the temperature range of 1400–1700°C by conventional solid–oxide reaction route. The effect of different aluminas (viz., hydrated and calcined) on the densification, microstructure, and properties of Al₂O₃–Cr₂O₃ refractories was investigated without changing the Cr₂O₃ source. The starting materials were analyzed to determine the chemical composition, mineralogy, density, surface area, and particle size. Sintered materials were characterized in terms of densification, phase assemblage, and mechanical strength at room temperature and at higher temperatures. Microstructural evolution at different sintering temperature was correlated with sintering characteristics. It can be concluded that the Al₂O₃–Cr₂O₃ refractories prepared with hydrated alumina as Al₂O₃ source show better densification and hot mechanical strength than corresponding calcined variety.     

Synthesis of SiC ceramics from processed cellulosic bio-precursor

Synthesis of SiC ceramic from processed cellulosic bio-precursor was investigated. Bamboo (Bambusa tulda Roxb.) plants abundantly available in the Jorhat district of Assam, India, were selected for extraction of fibers following Kraft pulping method and bleached bamboo pulp fibers were suitably cast in the form of rectangular boards. Coir fibers available in the Alleppy district of Kerala, India, were initially digested with dilute alkali, mixed with cellulose acetate solution, air dried and then hot-pressed at 140 ± 5 °C under 2.0–2.5 MPa pressure to make rectangular boards. Well-characterized processed bio-precursors were pyrolysed at ～800 °C under flowing N₂ atmosphere to prepare the bio-carbonaceous preforms (carbon templates) which showed nearly uniform shrinkages in all directions. Coir fiber composite board carbon showed lower pyrolytic weight loss (～66%), higher density (0.49 g cm^?3), lower porosity (～58%) and narrower pore diameter (10 μm) compared to the cast bamboo pulp fiber board carbon. The carbon samples showed perfect retention of fibrous morphological features of hierarchically grown bio-structures. Ceramization of carbon templates could be done by reactive melt silicon infiltration into porous channels at ～1600 °C under vacuum. The final ceramics were adequately dense (%theoretical density > 99%), showed negligible linear dimensional changes (indicating net-dimension formation capability), presence of crystalline Si and SiC phases and duplex microstructure with complete preservation of fibrous architecture of plant bio-structure. The Si/SiC ceramic composite synthesized from coir fiber board gave room temperature 3-point flexural strength and Young's modulus values of 121 MPa and 276 GPa, respectively. Both the ceramic composites showed adequate oxidation resistance during heating at 1300 °C for 7 h in air.     

Ceiling mounted personalized ventilation system in hot and humid climate—An energy analysis

This study is to evaluate energy saving potential of ceiling mounted personalized ventilation (PV) system in conjunction with background mixing ventilation compared with mixing ventilation system alone and with mixing ventilation system when occupants are provided with individually controlled desk fans for generating additional air movement at each desk. Control strategy applied includes different number of personalized ventilation air terminal devices used and different PV airflow rates supplied. Energy calculation is based on design conditions in Singapore, representing a hot and humid climate. The results reveal that increasing room temperature can save cooling energy when the combination of PV with ceiling mounted personalized ventilation nozzles and background mixing ventilation is used. In this case the energy for transport of air increases but the total energy decreases, i.e. energy can be saved due to elevated room temperature. Comparing with mixing ventilation plus desk fans, ceiling mounted personalized ventilation cannot only realize better cooling effect but also decrease the total energy consumption.     

Design and Synthesis of Xanthone Analogues Conjugated with Aza-aromatic Substituents as Promising G-Quadruplex Stabilizing Ligands and their Selective Cancer Cell Cytotoxic Action

We have examined the stabilization of higher-order noncanonical G-quadruplex (G4) DNA structures formed by the G-rich sequences in the promoter region of oncogenes such as c-MYC, c-KIT, VEGF and BCl2 by newly synthesized, novel nitrogen-containing aromatics conjugated to xanthone moiety. Compounds with N-heterocyclic substituents such as pyridine (XNiso), benzimidazole (XBIm), quinoxaline (XQX) and fluorophore dansyl (XDan) showed greater effectiveness in stabilizing the G4 DNA as well as selective cytotoxicity for cancer cells (mainly A549) over normal cells both in terms of UV-Vis spectral titrations and cytotoxicity assay. Both fluorescence spectral titrimetric measurements and circular dichroism (CD) melting experiments further substantiated the G4 stabilization phenomenon by these small-molecular ligands. In addition, these compounds could induce the formation of parallel G4 structures in the absence of any added salt condition in Tris ⋅ HCl buffer at 25 °C. In a polymerase stop assay, the formation of stable G4 structures in the promoter of oncogenes and halting of DNA synthesis in the presence of the above-mentioned compounds was demonstrated by using oncogene promoter as the DNA synthesis template. Apoptosis-mediated cell death of the cancer cells was proved by Annexin V-PI dual staining assay and cell-cycle arrest occurred in the S phase of the cell cycles. The plausible mode of binding involves the stacking of the xanthone core on the G4 DNA plane with the possibility of interaction with the 5’-overhang as indicated by molecular dynamics simulation studies.     

Independent testing and validation of prototype hydrogen sensors

In this article, the independent testing and validation of a packaged, electrochemical prototype hydrogen sensor at the National Renewable Energy Laboratory (NREL) is reported. Custom electronics were developed to be compatible with the data acquisition system at NREL. The specialized hydrogen sensor-testing laboratory at NREL used a variety of standardized test protocols to assess sensor performance. The system controlled and monitored humidity, pressure, and hydrogen gas concentration and introduced interference gases such as methane, carbon dioxide, carbon monoxide and ammonia.