Characteristics of flamelets in spray flames formed in a laminar counterflow

A two-dimensional numerical simulation of a spray flame formed in a laminar counterflow is presented, and the flamelet characteristics are studied in detail. The effects of strain rate, equivalence ratio, and droplet size are examined in terms of mixture fraction and scalar dissipation rate. n-Decane (C₁₀H₂₂) is used as a liquid spray fuel, and the droplet motion is calculated by the Lagrangian method without the parcel model. A one-step global reaction is employed for the combustion reaction model. The results show that there appear large differences in the trends of gaseous temperature and mass fractions of chemical species in the mixture fraction space between the spray flame and the gaseous diffusion flame. The gas temperature in the spray flame is much higher than that in the gaseous diffusion flame. This is due to the much lower scalar dissipation rate and the coexistence of premixed and diffusion-limited combustion in the spray flame. For the spray flames, gas temperature and mass fractions of chemical species are not unique functions of the mixture fraction scalar dissipation rate. This is because the production rate of the mixture fraction, namely evaporation rate of the droplets, in the upstream region is not in proportion to its transport-diffusion rate in the downstream region. The behavior shows marked differences as the strain rate decreases, the equivalence ratio increases, or the droplet size decreases.     

Fabrication and operation limit of lead-free PTCR ceramics using BaTiO3–(Bi1/2Na1/2)TiO3 system

The electric properties of BaTiO₃–(Bi_1/2Na_1/2)TiO₃ (BT–BNT) solid solution ceramics were studied as a lead-free PTCR (positive temperature coefficient of resistivity) thermistor material usable over 130°C. For determining the maximum switching temperature T _s, the phase diagram of BT–BNT binary system was clarified. Two semiconductorization processes and their electric properties are described. The lanthanum(La)-doped BBNT ceramics sintered in air still showed dielectric behaviors, but the niobium(Nb)-doped ones had a low resistivity at room temperature, ρ _RT, on the order of 10³ Ωcm and showed a PTC behavior. Sintering under a low O₂ atmosphere produces BT–BNT ceramics with less than 10² Ωcm compared to those prepared in air. Our current research produced the BBNT ceramics with T _s values around 210°C by increasing the (Bi_1/2Na_1/2) content in the ceramics.     

Orientation of nanowires consisting of poly(3-hexylthiophene) using strong magnetic field

Nanowires consisting of regioregular poly(3-hexylthiophene) (P3HT) as a conducting polymer were prepared using p-xylene. Magnetic processing of the nanowires was carried out using two superconducting magnets with horizontal (B_max = 8 T) and vertical (B_max = 10 T) directions. The formation of the nanowires was confirmed by atomic force microscopy (AFM) measurement. The results from the AFM images and the polarized absorption spectra on glass plates indicated that the nanowires partly oriented themselves with their long axes, which are parallel to the π–π stacking direction, being perpendicular to the magnetic field. The magnetic orientation is most likely ascribed to anisotropy in the magnetic susceptibilities of the ordered P3HT in the nanowires.     

Product mix problems considering several probabilistic conditions and flexibility of constraints

This paper considers product mix problems including randomness of future returns, ambiguity of coefficients and flexibility of upper value with respect to each constraint such as budget, human resource, time and several costs. Particularly, the flexibility is assumed to be a fuzzy goal. Then, several models based on maximizing total future profits under a level of satisfaction to each fuzzy goal are proposed. Furthermore, the model considering preference ranking to each fuzzy goal of constraints is proposed. Since these problems are basically formulated as nonlinear programming problems, the transformations into deterministic equivalent problems are introduced and the efficient solution methods are developed. A numerical example for product mix problem is given to illustrate our proposed models.     

Biochip with integrated pumps for plug-based sequential exchange of solutions

A novel method for exchanging solutions used in biochemical analyses and a device to carry out the exchange are proposed. An array of plugs formed using six injectors was transported in a microflow channel using a main pump located at one end of the main flow channel. The injectors and main pump were operated on the basis of the change in volume caused by the electrolysis of water. Bubbles were produced from working electrodes; these bubbles caused a diaphragm placed below the injectors to inflate and occlude the inlet of the solution reservoir. Increase in the number of bubbles caused the reservoir to inject the solution into the main flow channel in the form of a plug. Each plug was individually transported downstream to the sensing area by the main pump, which was operated in a similar manner to the injector. The device was used for the detection of a tumor marker, α-fetoprotein (AFP). Plugs of necessary solutions were individually transported to the sensing area with immobilized primary antibodies to allow antigen–antibody binding, cleaning, and detection. The fluorescence intensity from the antibodies showed clear dependence on the concentration of AFP. The immobilization of antibodies could also be carried out on-chip.     

Microanalyses on the RuO2 Particle–Glass Matrix Interface in Thick-Film Resistors with Piezoresistive Effects

The piezoresistive mechanisms of composite thick films based on RuO₂ particles and both calcium-borosilicate and bismuth-borosilicate glass matrices were investigated by chemical and electrical microanalyses. The resistor based on bismuth-borosilicate glass showed higher sensitivity than that based on calcium-borosilicate glass. It was confirmed that the diffusion of ruthenium into glass affects the binding state of RuO₂ at the interface of the glass. Furthermore, an intermediate resistive layer is detected around the RuO₂ particle. These results suggest that the piezoresistive effect is related to a change in the electrical conductivity of the interfacial reaction layer caused by the diffusion of ruthenium into glass.     

Colloidal Processing and Mechanical Properties of Whisker-Reinforced Mullite Matrix Composites

Aqueous colloidal suspensions in the two systems of CVD-processed ultrafine mullite powder (<0.1 μm), -Si₃N₄ whisker and -mullite whisker, were prepared near the isoelectric point of mullite (pH 7.0) to prevent cracking during drying of wet green compacts consolidated by filtration. The freeze-dried porous green compacts were hot-pressed with a carbon die at 1500°C for 1 h at a pressure of 39 MPa in N₂ atmosphere. The relative densities of the mullite matrix composites with whiskers of 0 to 10 vol% were in the range of 95.2% to 99.8%. Increasing the fraction of Si₃N₄ whisker increased the density, flexural strength, and fracture toughness of the hot-pressed composites. On the other hand, addition of the mullite whisker increased the fracture toughness but decreased the density and strength of the composites.     

Phylogenetic analysis of Rhodococcus erythropolis based on the variation of ribosomal proteins as observed by matrix-assisted laser desorption ionization-mass spectrometry without using genome information

Rhodococcus erythropolis strains characterized as antibiotic producers can be classified into three groups according to their antibiotic spectrum and growth compatibility. Due to their high genotypic similarity, the taxonomic relationship of these strains has not been elucidated. In this study, ribosomal protein profiling using matrix-assisted laser desorption ionization-mass spectrometry (MALDI-MS) was employed to classify twenty-one strains of R. erythropolis (15 antibiotic producers and 6 non-antibiotic producers). In the first step in this method, a total of 30 intense peaks observed for purified ribosomal subunit proteins of the type strain (R. erythropolis JCM 3201^T) were selected as the reference peaks. The mass spectra observed for the cell lysates of each sample strain were then checked as to whether peaks were observed at the same masses of the reference peaks. The results of peak matching were processed by cluster analysis, generating a dendrogram. Four major clusters of the R. erythropolis strains corresponded to three antibiotic groups and the non-antibiotic group. Furthermore, the topology of the dendrogram was highly comparable with the phylogenetic tree based on DNA gyrase subunit B gene (gyrB) sequencing. These results indicate that our proposed ribosomal protein profiling method using MALDI-MS is a potentially reliable and sufficiently high-throughput technique for the taxonomic analysis of closely related bacterial strains without using DNA sequence information.     

Effects of siRNAs targeting the spacer sequence of plant RNAi vectors on the specificity and efficiency of RNAi

Small interfering RNAs (siRNAs) generated from the spacer region of hairpin RNAs were not detected in the RNA interference (RNAi) plants targeting the fatty acid desaturase gene. The expression of the desaturase gene was stably suppressed even when siRNAs targeting the spacer sequences were introduced into this plant.