In-situ monitoring of surface stoichiometry and growth kinetics study of GaN (0001) in MOVPE by spectroscopic ellipsometry

GaN surface stoichiometry and growth kinetics in MOVPE were studied by in-situ spectroscopic ellipsometry. The effect of MOVPE conditions on both the surface stoichiometry and growth kinetics was investigated. The surface stoichiometry, such as N-rich, Ga-rich and Ga-excess surfaces, was monitored, and was drastically changed by the variation of the NH₃ partial pressure. When the TMG supply was interrupted during the growth, the layer-by-layer decomposition/revaporation was observed in H₂/NH₃ ambient. The decomposition rate was measured as a function of the NH₃ flow rate at the conventional epilayer growth temperatures (1050–1140 C). The decomposition rate was decreased with the increase in the N coverage on the GaN surface. it was found that the surface stoichiometry is a very important parameter for the control of the MOVPE growth kinetics.     

Comparative studies on Ar and He closed-cycle MHD power plants combined with fossil fuel

Comparative studies on Ar and He closed-cycle MHD power plants combined with fossil fuel are performed. The sizes of a regenerative heat exchanger and a boiler are expected to be smaller for He than for Ar. The pressure loss of a working gas in a regenerative heat exchanger is reduced for He. The purification subsystem for He is expected to be more compact and economical than that for Ar; but a larger compressor is required for He than for Ar.     

Control schemes and transient characteristics of a high‐speed phase shifter for power flow control in power transmission systems

In recent years, attention has been paid to the concept of FACTS (Flexible AC Transmission Systems), along with significant progress in power electronic technology. A high‐speed phase shifter, which is one of the most promising devices in the FACTS concept, has the potential of power flow control and/or voltage stability in power transmission systems. In this paper, theory and experiment reveal that conventional high‐speed phase shifters may cause power swings in a transient state as a result of coupling between instantaneous active and reactive power control loops. Thus, two new control schemes for a high‐speed phase shifter are proposed to achieve both power flow control and power swing damping. The second proposed control scheme is based on the control scheme of an already proposed series active filter. Simulated and experimental results agree well with analytical results, not only in steady states but also in transient states. © 1999 Scripta Technica, Electr Eng Jpn, 128(2): 74–82, 1999     

Control and performance of a zero‐current‐switched,three‐phase PWM inverter equipped with resonant circuits on the ac side

This paper presents a zero‐current‐switched voltage‐fed inverter equipped with resonant circuits on the ac side. The current flowing through a switching device, that is, IGBT, is the sum of the load current and the resonant current. When the amplitude of the resonant current is larger than that of the load current, the current in the switching device becomes zero at an instant in each resonant cycle. This allows the switching device to be turned on or off at the zero current. The zero‐current switching makes a significant contribution to reduction of switching losses and electromagnetic noises. In this paper, the principle of zero‐current‐switching operation, along with a novel control scheme, is described from a theoretical and practical point of view. Experimental results obtained from a laboratory system of 5 kVA verify the practicability. Moreover, the switching and conduction losses of the proposed soft‐switched inverter are compared with those of a conventional hard‐switched inverter. © 2000 Scripta Technica, Electr Eng Jpn, 131(4): 85–95, 2000     

Experimental verification of the effect of a voltage‐detection‐based shunt active filter for harmonic damping throughout a power distribution line

This paper is focused on a voltage‐detection‐based shunt active filter for installation on a power distribution system. A main objective of the active filter is to achieve damping of harmonic propagation coming from series/parallel resonance between capacitors for power factor correction and line inductors in the distribution system. The active filter installed at the end terminal of a distribution feeder is controlled in such a way as to present infinite impedance to the external circuit for the fundamental frequency, and to exhibit low resistance for harmonic frequencies. As a result, the active filter acts as a damping resistor for the harmonic propagation, like a 50‐Ω terminator installed at the end of a signal transmission line. It is verified by experiment that the active filter intended for harmonic termination has the capability of harmonic damping throughout the distribution feeder. © 2000 Scripta Technica, Electr Eng Jpn, 133(2): 1–10, 2000     

Development of ‘UR-System 2’: a training system for recovery of motor function of plegic upper limb after stroke

We developed a new training system, called ‘UR-System 2’, for the recovery of motor function of a plegic upper limb after stroke. UR-System 2, which was redesigned based on knowledge gained from clinical tests using UR-System 1, was newly equipped with a function for testing the motor function of patients, such as isolated movement. In order to verify the effectiveness of UR-System 2, we conducted the following procedures: we verified the safety of training in healthy persons; we gathered standard data on pronation and supination of healthy forearms during tests; and, we verified that the test function was effective in evaluating the recovery effect of isolated movement in two hemiplegic patients.     

Enrichment of arachidonic acid: Selective hydrolysis of a single-cell oil fromMortierella withCandida cylindracea lipase

Three lipases, isolated previously in our laboratory, and a known lipase fromCandida cylindracea were screened for the enrichment of arachidonic acid (AA). The enzyme fromC. cylindracea was the most effective for the production of oil with high concentration of AA. When a single-cell oil fromMortierella alpina, containing 25% AA, was hydrolyzed with this lipase for 16 h at 35°C, the resulting glycerides contained 50% AA at 52% hydrolysis. After this, no further hydrolysis occurred, even with additional lipase. However, when the glycerides were extracted from the hydrolyzate and were hydrolyzed again with new lipase, the resulting oil contained 60% AA, with a recovery of 75% of its initial AA content. Triglycerides were the main components of the resulting oil. The release of each fatty acid from the oil depended on the hydrolysis rate of its ester. The fatty acid, whose ester is the poorest substrate for the enzyme, is concentrated in the glycerides.     

Effects of electrode arrangement and pressure on synthesis of diamond films by arc discharge plasma jet chemical vapor deposition

The setup and deposition conditions of electrode arrangement and pressure have been studied to synthesize diamond films at high growth rate on wide area efficiently by arc discharge plasma jet chemical vapor deposition. An apparatus has been used in which four plasma torches, one is used for cathode and the others for divided anodes, are arranged and the positions of these torches are changeable. Growth rate, deposition area and thickness of diamond films have increased with changing the electrode arrangements without improvement of thickness variation. Maximum growth rate of our apparatus has occurred at the pressure of 6.7 kPa and diamond films that have less variations of quality and surface roughness have been synthesized at lower pressure during deposition. Moreover, a high conversion rate, which is the ratio of carbon atoms that form diamond in supplied methane gas, of 16% has been obtained at the pressure of 6.7 kPa and methane concentration of 2%.     

Change in liquid temperature behind the impeller blades with impeller speed in boiling stirred tanks

In our previous study (Fukuda, R., Tokumura, M., Znad, H.T. and Kawase, Y., 2009, Vapour generation from the impellers in boiling stirred tank reactors. Chem Eng Res Des, 87: 452–459), it was found that in boiling stirred tanks with multiple impeller systems vapour was generated from the heater at lower impeller speeds and with an increase in impeller speed most vapour was generated from the top impeller rather than the lower impellers and the heater. The change of nucleation sites with the impeller speed might be controlled by the local liquid temperature. Therefore we measured the liquid temperature behind the impellers blades and found the decrease in liquid temperature with increasing impeller speed. In this paper, a simple model was developed to predict the change in liquid temperature behind the impeller blades in which nucleation takes place. In the proposed model based on the results for pressure distribution on the impeller blade in the literature, the liquid temperature behind the impeller blades is estimated from the measured power consumption. The validation of the proposed model was conducted using the experimental results in our previous study and reasonable agreement was obtained.