Catharanthine oxidation in flavin mononucleotide-mediated catharanthine-vindoline coupling reaction for synthesis of dimeric indole alkaloids under near-ultraviolet light

A reaction model for the flavin mononucleotide-mediated coupling of catharanthine (C) and vindoline (V) under near-ultraviolet light was established based on the results of experiments on the effects of various physical and chemical factors on the disappearance of C and V, and the synthesis of the product, a dihydropyridinium intermediate (IM). The following events were deduced to occur. (i) C is oxidized in the presence of FMN and oxygen under near-ultraviolet light (C(OX1)). (ii) C(OX1) then couples with V to form IM. Degradation of C occurs simultaneously with its specific oxidation, as a result of which a part of the C is converted into the product (C*) which is incapable of coupling with V. When a reaction in which C(OX1) is further oxidized to another form (C(OX2)) is added and the counterpart for the coupling with V is changed to C(OX2) from C(OX1), the reaction model more appropriately describes the exponential increase in the product, IM, that occurs in the early stage of the coupling reaction. (iii) The degradation rate of IM is much greater after C has been consumed than before its disappearance. Using this reaction model, the coupling reactions under basal and optimized conditions were simulated and the results showed a good fit with the experimental values under both conditions. The kinetic study suggests that manganese ion (Mn2+) stimulates the binding of C(OX2) with V in addition to suppressing the degradation of C, resulting in an increased yield of IM. Mn2+ thus appears to be an important factor in the coupling reaction, in which it plays two different roles.     

Experimental verification of the effect of a voltage‐detection‐based shunt active filter for harmonic damping throughout a power distribution line

This paper is focused on a voltage‐detection‐based shunt active filter for installation on a power distribution system. A main objective of the active filter is to achieve damping of harmonic propagation coming from series/parallel resonance between capacitors for power factor correction and line inductors in the distribution system. The active filter installed at the end terminal of a distribution feeder is controlled in such a way as to present infinite impedance to the external circuit for the fundamental frequency, and to exhibit low resistance for harmonic frequencies. As a result, the active filter acts as a damping resistor for the harmonic propagation, like a 50‐Ω terminator installed at the end of a signal transmission line. It is verified by experiment that the active filter intended for harmonic termination has the capability of harmonic damping throughout the distribution feeder. © 2000 Scripta Technica, Electr Eng Jpn, 133(2): 1–10, 2000     

A three‐phase hybrid stepping motor drive system combined with position‐sensorless closed‐loop control

This paper proposes a drive system for a three‐phase hybrid stepping motor, combining sensorless closed‐loop control with conventional open‐loop control. It is characterized by sophisticated control providing both prevention of pulling out from synchronism and suppression of natural rotor oscillation, without any position sensor attached to the motor shaft. A switching technique in chopper control which can enlarge the speed range controllable in the sensorless closed‐loop control is described. Starting and stopping sequences are developed to reduce mechanical natural oscillation produced in the transient state. Finally, the proposed drive system is compared experimentally with a conventional constant‐current open‐loop drive system. It is shown that the proposed drive system can perform the switchover from starting to sensorless closed‐loop operation within 20 ms, and can reduce the natural oscillation caused just after positioning. © 2000 Scripta Technica, Electr Eng Jpn, 131(3): 80–90, 2000     

Control and performance of a zero‐current‐switched,three‐phase PWM inverter equipped with resonant circuits on the ac side

This paper presents a zero‐current‐switched voltage‐fed inverter equipped with resonant circuits on the ac side. The current flowing through a switching device, that is, IGBT, is the sum of the load current and the resonant current. When the amplitude of the resonant current is larger than that of the load current, the current in the switching device becomes zero at an instant in each resonant cycle. This allows the switching device to be turned on or off at the zero current. The zero‐current switching makes a significant contribution to reduction of switching losses and electromagnetic noises. In this paper, the principle of zero‐current‐switching operation, along with a novel control scheme, is described from a theoretical and practical point of view. Experimental results obtained from a laboratory system of 5 kVA verify the practicability. Moreover, the switching and conduction losses of the proposed soft‐switched inverter are compared with those of a conventional hard‐switched inverter. © 2000 Scripta Technica, Electr Eng Jpn, 131(4): 85–95, 2000     

Control schemes and transient characteristics of a high‐speed phase shifter for power flow control in power transmission systems

In recent years, attention has been paid to the concept of FACTS (Flexible AC Transmission Systems), along with significant progress in power electronic technology. A high‐speed phase shifter, which is one of the most promising devices in the FACTS concept, has the potential of power flow control and/or voltage stability in power transmission systems. In this paper, theory and experiment reveal that conventional high‐speed phase shifters may cause power swings in a transient state as a result of coupling between instantaneous active and reactive power control loops. Thus, two new control schemes for a high‐speed phase shifter are proposed to achieve both power flow control and power swing damping. The second proposed control scheme is based on the control scheme of an already proposed series active filter. Simulated and experimental results agree well with analytical results, not only in steady states but also in transient states. © 1999 Scripta Technica, Electr Eng Jpn, 128(2): 74–82, 1999     

Measurement of group refractive index wavelength dependence using a low-coherence tandem interferometer

A technique for the measurement of the group refractive index wavelength dependence of optical materials using a low-coherence tandem interferometer and a spectrometer is proposed. Four channeled spectra resulting from interferences of light beams from different pairs of optical paths are used for the calculation of optical path differences. The group refractive index wavelength dependence is calculated from these optical path differences generated from the sample under measurement. No a priori information of the geometric thickness of a sample is required. The wavelength dependence of the group refractive index of the samples BK7 parallel plate of 5.200 and 10.025 mm from 675 to 850 nm is experimentally measured with an accuracy of the order of 10(-5) and a repeatability of the order of 10(-9).     

Estimation of heat generation rate in solid oxide fuel cell module from single cell performance and module performance based on impedance analysis

Heat generation rate in SOFC module was estimated under various thermal self-sustained conditions. SOFC module and system was designed to evaluate power generation property and temperature of module. Single cell was also evaluated the performance and electrode overpotential by impedance analysis under the similar condition to module power generation state. We estimated the heat generation rate with enthalpy calculation based on the actual module performance, and also with entropy calculation based on the impedance analysis of single cell. It was found that the heat generation rate calculated by enthalpy is approximately corresponded with that calculated by entropy. There still contains small error between heat generation rate calculated by enthalpy and that calculated by entropy. It was considered that these errors are originated from distribution in stack temperature and reforming gas temperature in the module. According to impedance analysis, it was found that the ohmic resistance is varied under operating condition and related with the current distribution which is calculated with the current path length in the cell. It was suggested that power generation state of module is affected by the current path length in the cell (in another word, distribution of power density) and distribution of overpotential; these phenomena is dominated by gas composition and thermal self-sustainable temperature.     

Selective protein separation using siliceous materials with a trimethoxysilane-containing glycopolymer

A copolymer with α-D-mannose (Man) and trimethoxysilane (TMS) units was synthesized for immobilization on siliceous matrices such as a sensor cell and membrane. Immobilization of the trimethoxysilane-containing copolymer on the matrices was readily performed by incubation at high heat. The recognition of lectin by poly(Man-r-TMS) was evaluated by measurement with a quartz crystal microbalance (QCM) and adsorption on an affinity membrane, QCM results showed that the mannose-binding protein, concanavalin A, was specifically bound on a poly(Man-r-TMS)-immobilized cell with a higher binding constant than bovine serum albumin. The amount of concanavalin A adsorbed during permeation through a poly(Man-r-TMS)-immobilized membrane was higher than that through an unmodified membrane. Moreover, the concanavalin A adsorbed onto the poly(Man-r-TMS)-immobilized membrane was recoverable by permeation of a mannose derivative at high concentration.