STEAM DRYING OF SINTERED SPHERES OF GLASS BEADS

ABSTRACT

Superheated steam drying of sintered spheres of glass beads with different diameters is investigated to reveal the effects of the gravitational force on drying rates. In a previous study, the drying rate curves of small samples with coarse glass beads in which the frictional resistance to flow of water and the effect of the gravitational force are negligible, were predicted by an evaporation zone model.In the present investigation, the drying rate curves of sintered spheres of glass beads with diameters ranging from 1.53×10^-2m to 4.99×lO^-2m are experimentally and theoretically obtained, and also the capillary pressure curves are measured by use of Haines' apparatus. The drying rate curves of large samples in which the effect of the gravitational force can not be negligible, are compared with those for small samples and the difference among these curves is discussed in terms of the moisture distributions which are estimated from the evaporation zone model with the observed capillary pressure curves.     

Technical investigation on small water leakage incident occurrence in mercury target of J-PARC

Japan Proton Accelerator Research Complex experienced failures of two mercury targets, which were Target #5 and #7, in 2015 when the facility was operating with a proton beam power of 500 kW. The failures involved coolant water leak from the water shroud. In this paper, we investigate the root cause of the Target #5 failure. The results of the visual inspections, mockup tests, and analytical evaluations suggested that the water leak was caused by the possible combination of two incidents. One was the diffusion bonding failure due to the large thermal stress induced by welding of the bolt head during the fabrication process, and the other was the thermal fatigue failure of the seal weld due to the repetitive beam shutdown during beam operation. Though the investigation into the root cause of the Target #7 failure is still going on, these target failures point to the importance of eliminating initial defects and the need to secure the rigidity and stability of welded structures. The next mercury target, Target #8, was fabricated with an improved design and fabrication process to reduce the possibility of similar failures. The beam operation of this mercury target is planned to be started in October 2017.     

POROSITY AND RESIDUAL EQUILIBRIUM SATURATION OF SINTERED SPHERES OF GLASS BEADS

Sintered spheres(made of glass beads) were simply produced with a definite diameter, with a precision of ±0·5 mm in diameter, for a wide range of sintered angles (0-27°). The experimental values of the porosity of the sintered spheres were consistent with the calculated results for the coordination number N ≠ 8. The residual equilibrium saturation, as one of the basic physical properties of sintered glass beads was investigated experimentally and theoretically, resulting in the presence of a distribution in the angle of pendular ring.     

Incline compensation control using an air-spring type active isolated apparatus

In order to avoid the deformation of main body supported by air-spring type active isolated apparatus, a pressure feedback was previously introduced for its isolated apparatus. The primal purpose of this feedback was to suppress the deformation of the main body by controlling air-spring force. Furthermore the author recognize that the incline of the main body due to XY stage scanning will be easily compensated by utilizing that the driving mechanism of air-spring with the pressure feedback becomes an astatic system. If the incline of the main body is effectively corrected, the precise scanning of XY stage is expected because the disturbance for the control loop of XY stage is removed.Firstly, this paper briefly shows the principle of the pressure feedback which provides a basis for the incline compensation. Secondly, the feed-forward scheme for its compensation is clarified. Finally, the experimental results of the incline compensation are shown.     

Clinicopathological analysis and therapy in hepatitis C virus-associated nephropathy

The authors evaluated, using computer image analysis system, 15 renal biopsy specimens from patients with MCD and 15 from patients with FSGS. As a control group 5 biopsy and 10 autopsy renal specimens were used. These studies revealed, that in MCD glomeruli showed proliferative changes unrecognizable by light microscopy. In FSGS glomeruli without sclerotic changes were larger than in controls and showed glomerular cells proliferation (per unit of glomerular area) similar to MCD. FSGS in comparison with MCD showed larger glomeruli and prominent interstitial fibrosis. These observations appeared to be helpful in distinguishing MCD and recent forms of FSGS. There were no correlations between relative interstitial volume and glomerular changes in MCD as well as in FSGS. The authors concluded, that histomorphometry can't be used instead of morphological examinations of renal biopsy specimens, but it gives objective informations about progression of the illness and may be useful in differential diagnosis of selected cases of MCD and FSGS.     

Development of a deep-hole, laser-guide boring tool: the boring of workpieces with a thin wall and an inclined prebored hole

A laser-guided BTA tool has been developed to prevent axial hole deviations. Four kinds of experiments were conducted to examine the performance of this tool in detail and to determine its practical application using a duralumin (A2017-T4) workpiece with a prebored 108-mm diameter hole. The first experiment was performed to examine the conditions of the hole deviation in the case of normal deep-hole boring. The second was to examine whether the tool corrects for the stated hole deviation. The third was to examine whether the tool can go straight through to the target without shifting toward a thin wall (t = 0.7 mm) on one side of the workpiece. The fourth was to examine whether the tool can be guided toward the target without affecting a prebored hole, which was inclined to radial direction at 100 μm for a hole length of 100 mm. The experiments were performed with a rotating tool-stationary workpiece system. Rotational speed was 270 rpm and feed ws 0.125 mm/rev. Tool diameter was 110 mm. The results show that the tool can be guided to go straight through toward the target despite the disturbances.     

Concentration distribution of antioxidant additive BHT in polypropylene after heating

The concentration distribution of an antioxidant 2,6-di-tert-butyl-p-cresol (BHT) in the polypropylene (PP) after heating the film containing BHT for a long period of time in succession was studied with use of the rolled film method. The film of 0.003 cm in thickness containing uniformly 710 mg kg^?1 of BHT was wound tightly around a glass tube. At the beginning, BHT was distributed uniformly in all layers, and after a given time of the heat treatment at 70–100°C, a remarkable alteration of the concentration distribution of BHT in PP took place. The relations between BHT concentration and the distance from the surface were shown by parabolic curves after heating. The BHT concentration was always kept at almost zero concentration at the surface layer of the rolled film. Assuming that the diffusion obeys Fick's law, the diffusion coefficients at 70, 80, 90, and 100°C were estimated to be 1.05, 4.17, 8.69, and 24.7 × 10^?9 cm² s^?1, respectively. The activation energy was calculated as 105 kJ mol^?1.     

Electrical properties and microstructure in the system ceria-alkaline earth oxide

The ionic conduction of oxygen in the ceria-alkaline earth oxide system was investigated as a function of temperature, partial pressure of oxygen and oxide composition, together with its crystal structure, density, and microstructure. Undoped ceria and its solid solution with alkaline earth oxides have a cubic fluorite structure. The ionic conductivity of ceria is greatly enhanced by additions of calcia and strontia, even when they are added in excess of the solubility limit. The conductivities of ceria-calcia and ceria-strontia were much higher than those of calcia-and yttria-stabilized zirconia. Up to the limit of calcia and strontia, the ionic transference number was nearly unity in the temperature range between 600 and 900°C. With an increase in calcia and strontia content, the ionic conductivity was little affected by the presence of a second phase of CaO and SrCeO₃.