Design of electrofusion joints and evaluation of fusion strength using fusion simulation technology

Fusion simulation is one of the key techniques in designing and producing electrofusion (EF) joints for gas distribution and in evaluating fusion joint integrity. This paper describes the result of a numerical simulation of a thermal fusion process, using the finite element method. A nonlinear heat transfer computer program was used to obtain the temperature profile of a large electrofusion joint at fusion. The effects of applied voltage, heating time, wire pitch, and ambient temperature were examined for designing a 150-mm EF joint. A method to shorten the cooling time was also investigated. The fusion condition range suitable for a 150-mm EF joint was found to be slightly narrower than that suitable for a 50-mm EF joint. Examination of the effect of wire pitch revealed that if the pitch is extremely large, thermal degradation starts in the resin close to the wire before the fusion-interface strength reaches the maximum value. We have developed a program to simulate the process of closing the gap between the pipe and the joint due to resin expansion and melting after the power is supplied.     

A scheme of picosecond pulse shaping using gain saturationcharacteristics of semiconductor laser amplifiers

To obtain high power, well shaped picosecond pulses from gain-switched semiconductor lasers, the use of dynamic gain saturation characteristics of semiconductor laser amplifiers was investigated theoretically and experimentally. A configuration of a reflected-wave amplifier (RWA) with single-side external coupling is introduced for pulse shaping, which is found to be suitable for enhancing dynamic gain saturation. By a combination of a distributed feedback laser oscillator at 1.3 μm in wavelength and a reflected-wave amplifier of 400 μm cavity length with asymmetric facet reflectivities of 0.01% and 30%, single-mode optical pulses with almost no tailing, full width at half maximum of 15 ps, and peak power exceeding 50 mW were obtained without pulse broadening, despite the considerable tail structure of the incident pulse     

Measurement of aerosol particles by dynamic light scattering-I. effects of non-Gaussian concentration fluctuation in real time photon correlation spectroscopy

Effects of non-Gaussian concentration fluctuations in real time photon correlation spectroscopy were investigated with several sizes of mono-disperse polystyrene latex particles. The non-Gaussian correlation model for a full or a quasi-full (scaled) correlator showed good performance for particle sizing in the case of scaled correlation. The clipped correlation showed an equivalent performance with the scaled correlation except for the case of non-Gaussian fluctuation, where the measured diameter became inaccurate more rapidly with decreasing particle concentration in the scattering volume. The cause of such an instability of PCS in the clipped mode is attributed to baseline fluctuations of the correlogram induced by information loss of the clipped correlator.     

A new voltage control equipment using fuzzy inference

Power system control equipment needs higher sensitivity and operational reliability. Advanced voltage control equipment is needed for reducing the frequency of tap changes and improving the characteristics (the relationship between the actual voltage and reference voltage) of the voltage to meet today's power system requirements. However, these objectives are in a trade-off relationship. Studies of voltage control derived from a knowledge base suitable for electric power systems can satisfy these objectives using fuzzy inference. Compared with corresponding conventional equipment, the new equipment improved the deviation of 30 min average voltage of 30 percent. This paper describes the design concept of new voltage control equipment using fuzzy inference. In addition, field test results are described along with rules of fuzzy inference, membership functions, and the deviation of 30 min average voltage through detailed simulation.     

High-performance polymer alloys of polybenzoxazine and bismaleimide

Two series of high-performance polymer alloys were prepared by mixing typical benzoxine monomers, 3-phenyl-3,4-dihydro-2H-1,3-benzoxazine (P-a) or 6,6-(1-methylethyliden)-bis-(3,4-dihydro-3-phenyl-2H-1,3-benzoxazine) (B-a), with a typical bismaleimide, 4,4-bismaleimidodiphenyl methane by various ratios followed by thermal treatment up to 240 °C. DSC and IR of the alloys were examined to follow the curing reaction. These analyses showed that the obtained polymer alloys are AB co-cross-linked polymer networks through the formation of ether linkage between the hydroxyl group of polybenoxazine and the double bond of bismaleimide. Viscoelastic analysis and softening temperature measurement revealed that the polymer alloys have much higher glass transition temperatures than those of each homopolymer. The thermal stability also increased with the increase of bismaleimide content as evidenced by TGA.     

High-performance carbon counter electrode for dye-sensitized solar cells

Here, we reported that a new carbon electrode prepared with an activated carbon was superior to a Pt sputtered electrode as the counter electrode of dye-sensitized solar cells. The photovoltaic performance was largely influenced by the roughness factor of carbon electrode. The open-circuit voltage increased by about 60 mV using the carbon counter electrode compared to the Pt counter electrode because of positive shift of the formal potential for I₃⁻/I⁻ couple.     

Hydrodynamic interaction and coalescence of two droplets under large step shear strains

We observed change in distance between two droplets in each step after application of large multi-step shear strains. Experiments were performed using a sliding plate apparatus. Large step shear strains were applied to two polyisobutylene droplets in poly(dimethyl siloxane) matrix in the same plane between the plates. The distance between the two droplets decreases with increasing the total shear strain, which is given by the product of the step strain magnitude and the number of application of the step strains. The two droplets coalesce when the distance becomes less than the diameter of the droplets. The slope for plots of the distance versus the total strain is independent of the step strain magnitude. This indicates that the effect per unit strain on the distance is the same, irrespective of the strain magnitude. It is suggested that a stronger hydrodynamic interaction between the droplets is the main cause for the droplet approach.     

Genotoxic effect of Physalis angulata L. (Solanaceae) extract on human lymphocytes treated in vitro

Physalis angulata L (Solanaceae) is a medicinal plant from North of Brazil, whose different extracts and infusions are commonly used in the popular medicine for the treatment of malaria, asthma, hepatitis, dermatitis and rheumatism. However, the genotoxic effects of P. angulata on human cells is not well known. The main purpose of the present study was to evaluate the in vitro genotoxic effects of aqueous extract of P. angulata using the comet assay and the micronucleus assay in human lymphocytes provided from 6 healthy donors. Treatments with P. angulata extracts were performed in vitro in order to access the extent of DNA damage. The comet assay has shown that treatments with P. angulata at 0.5, 1.0, 2.0, 3.0 and 6.0 microg/mL in culture medium were genotoxic. Lymphocytes treated with P. angulata at the concentrations of 3.0 and 6.0 microg/mL in culture medium showed a statistically significant increase in the frequency of micronucleus (p<0.05), however, the cytokinesis blocked proliferation index (CBPI) was not decreased after P. angulata treatment. In conclusion, the present work demonstrated the genotoxic effects of P. angulata extract on human lymphocytes in vitro.     

Suppression of photo-induced dilation in cyanide treated hydrogenated amorphous silicon films

Effects of cyanide (CN) treatment with hydrogenated amorphous silicon (a-Si:H) films have been investigated. The decrease of ΔV/V was observed in cyanide treated a-Si:H films and the successive thermal annealing at 200°C after CN treatment induced the further reduction of the ΔV/V. XPS spectra show the indirect evidence that the cyanide species is present within 10 nm from the hydrogenated amorphous silicon surface. The results of CN treatment with a-Si:H solar cells are demonstrated.