Radiation-induced polymerization of ethylene in pilot plant. III. Heavy-phase recycling process

Radiation-induced polymerization of ethylene using aqueous tert-butyl alcohol as medium was carried out in a large-scale pilot plant with a 50-liter central source-type reactor at a pressure of 105 to 395 kg/cm², temperature of 30° to 80°C, mean dose rate of 4.5 × 10⁴ to 1.9 × 10⁵ rads/hr, ethylene feed rate of 5.5 to 23.5 kg/hr, and medium feed rate of 21 to 102 l./hr. The space–time yield and molecular weight of the polymer were in the range of 4.7 to 16.8 g/l.-hr and 1.3 × 10⁴ to 8.9 × 10⁴, respectively. The space–time yield and molecular weight increased with mean residence time at 30°C, whereas at 80°C they became almost independent of the time. The space–time yield increased with pressure and dose rate, slightly decreased with temperature, and was maximum at ethylene molar fraction of 0.5. The polymer molecular weight increased with pressure and ethylene molar fraction, and decreased with dose rate and temperature. The total amount of deposited polymer on the reactor wall, source case wall, and scraping blades was usually less than 1 kg, which was negligibly small for the analysis of polymerization. Continuous discharge of the polymer slurry and production of fine-powder polyethylene were successfully carried out. In the central source-type reactor, a dose rate of 1.9 × 10⁵ rads/hr was obtained with a ⁶⁰Co source of ca. 12 kCi.     

Photosensitized hydrogen evolution from water using a single-walled carbon nanotube/fullerodendron/SiO2 coaxial nanohybrid

A coaxial nanohybrid consisting of a single-walled carbon nanotube (SWCNT), fullerodendron, and SiO(2) shows high-efficiency light-driven hydrogen evolution from water. Upon visible light irradiation, SWCNT/fullerodendron/SiO(2) coaxial nanohybrid shows hydrogen evolution activity in the presence of methyl viologen (MV(2+)), benzyldihydronicotinamide (BNAH), and a colloidal polyvinyl alcohol(PVA)-Pt.     

Anti‐windup synthesis for a model predictive control system

In this paper, an anti‐windup design problem for a model predictive control system is studied. The plant is assumed to be stable. First, we propose the structure of an output feedback model predictive controller with an anti‐windup compensator. Then we show a design method of the anti‐windup compensator that guarantees closed‐loop stability and improves the transient response. The design problem of the anti‐windup compensator is reduced to a linear matrix inequality (LMI) optimization problem. Further, it is shown that there always exists an anti‐windup compensator that ensures global asymptotic stability. © 2016 Institute of Electrical Engineers of Japan. Published by John Wiley & Sons, Inc.     

Experimental verification of the effect of a voltage‐detection‐based shunt active filter for harmonic damping throughout a power distribution line

This paper is focused on a voltage‐detection‐based shunt active filter for installation on a power distribution system. A main objective of the active filter is to achieve damping of harmonic propagation coming from series/parallel resonance between capacitors for power factor correction and line inductors in the distribution system. The active filter installed at the end terminal of a distribution feeder is controlled in such a way as to present infinite impedance to the external circuit for the fundamental frequency, and to exhibit low resistance for harmonic frequencies. As a result, the active filter acts as a damping resistor for the harmonic propagation, like a 50‐Ω terminator installed at the end of a signal transmission line. It is verified by experiment that the active filter intended for harmonic termination has the capability of harmonic damping throughout the distribution feeder. © 2000 Scripta Technica, Electr Eng Jpn, 133(2): 1–10, 2000     

Size dependence of THz region dielectric properties for barium titanate fine particles

Barium titanate (BaTiO₃) crystallites with various particle sizes from 22 to 500 nm were prepared by the two-step thermal decomposition method of barium titanyl oxalate. Various characterizations revealed that these particles were impurity-free, defect-free, dense BaTiO₃ particles. The powder dielectric measurement clarified that the dielectric constant of BaTiO₃ particles with a size of around 58 nm exhibited a maximum of over 15,000. To explain this size dependence, the THz region dielectric properties of BaTiO₃ fine particles, especially Slater mode frequency, were measured using the far infrared (FIR) reflection method. As the result, the lowest Slater mode frequency was obtained at 58 nm. This tendency was completely consistent with particle size dependence of the dielectric constant.     

Phase evolution and <110>-orientation mechanism in RTGG-processed BaTiO3 ceramics with electrical properties

The <110>-oriented BaTiO₃ ceramics were fabricated using BaCO₃ matrix and H_1.08Ti_1.73O₄.nH₂O (HTO) template particles, and the mechanism of BaTiO₃ phase formation was investigated. The dielectric, ferroelectric, and piezoelectric properties were also investigated. The transformation of the HTO phase into the TiO₂ bronze or TiO₂ (B) phase was observed at 600°C, where the BaTiO₃ nucleation was accompanied by the formation of a Ba₂TiO₄ phase. The TiO₂ phase reacted with the Ba₂TiO₄ phase at 800°C to give a BaTiO₃ phase, whereas its reaction with the BaTiO₃ resulted in the formation of BaTi₂O₅ phase that got decomposed into BaTiO₃ and Ba₆Ti₁₇O₄₀ phase at sintering temperature ≥1300°C. Sintering with samples’ embedding in BaTiO₃ powders prevented the formation of the Ba₆Ti₁₇O₄₀ secondary phase. The crystallographic orientation along the <110> direction (F₁₁₀) was developed by the epitaxial grain growth mechanism. In addition to the contribution of the grain-size increment for enhancing the F₁₁₀, the preservation of the platelike structure was also found to have a significant impact. The ceramics prepared by the embedded sintering (grain size ≈12.4 µm and F₁₁₀ = 83%) exhibited the room-temperature dielectric constant of 1708 and piezoelectric strain constant of 445 pm/V, which are higher than those of the BaTiO₃ ceramics with randomly oriented grains.     

Fabrication of 0.24Pb(In1/2Nb1/2)O3-0.42Pb(Mg1/3Nb2/3)O3-0.34PbTiO3 transparent ceramics by conventional sintering technique

0.24Pb(In_1/2Nb_1/2)O₃-0.42Pb(Mg_1/3Nb_2/3)O₃-0.34PbTiO₃ transparent ceramics were fabricated by a conventional sintering technique. Through optimization of sintering conditions of calcination and sintering temperatures and time, the obtained ceramics showed high optical transmittance of 53% and 71% at light wavelengths of 1300 and 2000 nm, respectively. The ceramics showed a rhombohedral to tetragonal phase transition at ~120°C and a tetragonal to cubic phase transition at 222°C. These transition temperatures were higher than those of 0.67Pb(Mg_1/3Nb_2/3)-0.33PbTiO₃ ceramics. In addition, the ceramics had a ferroelectric hysteresis loop, a large piezoelectric constant d₃₃ of 407 pC/N, and a planar electromechanical coupling factor k_p of 52%. These results suggest that the transparent ceramics may be used as a temperature-stable, linear electro-optic material.     

Inhibition of char deposition using a particle bed in heating section of supercritical water gasification

Supercritical water gasification (SCWG) has attracted attention as a technology for utilizing wet biomass. We used a fluidized bed of alumina particles to prevent blockage of a SCWG reactor. A glucose solution was heated in the reactor with and without fluidized alumina particles. In the absence of alumina particles, char particles formed homogeneously in the reactor, but the use of a fluidized bed resulted in accumulation of char particles at the reactor’s exit rather than inside the reactor. Therefore, the fluidized bed was effective at preventing blockage of the reactor. However, the alumina particles did not remove deposits from the reactor’s walls. Instead, the fluidized bed caused larger char particles to form, preventing their adhesion to the reactor’s wall.     

Thermite-Related Technologies for Use in Extreme Geothermal Environments

Thermite and related processes have attracted considerable attentions as highly useful technologies for material and energy supplies in extreme environments such as geothermal and disaster-stricken areas as well as in space exploration. As part of the development of casing pipes used in geothermal power plants started from the 1970s, long ceramic-lined pipes have been obtained via thermite reaction under effective centrifugal force without any additional heat treatment [Centrifugal-Thermite (C-T) process]. The potentials of the ceramic-lined pipes in deeper geothermal utilizations are revalidated in details by reviewing the results obtained through the erosion-corrosion tests carried out under the conditions of high velocities (up to 100 m/s) and various acidities (from pH 2.0 to pH 4.0) of two-phase flows provided by the geothermal field test apparatus at the Onikobe geothermal power plant in Japan. By reducing the FeO content of the ceramic layer processed under proper additives and reactant amounts, the tested ceramic-lined pipes were significantly improved compared to highly corrosion-resistant stainless steels. The technological advantages obtained through the development of the C-T process can show a useful model to promote thermite-related technologies onward.