Evaluation of the Fatigue Characteristics of Laser-processed Hot Work Tool Steel Based on Reliability

It is reported that laser-processing is effective to repair the heat checks, which are fine shallow cracks on a surfaceof die-casting dies.     

Current distribution in superconducting multistrands for ac use before and after quenching

A superconducting multistranded cable is used to realize high current capacity for ac use. The critical current value of the cable is reported to be less than the simple summation of the individual critical current value of each strand. The causes for such a degradation of the critical current value have not been revealed. This paper investigates the current distribution in multistrands before and after their quenching by using seven-strand superconducting cable and 7x7 cable. The following experimental results are derived: (1) the quenching is initiated at one strand in the cable; (2) the current in the quenched strand is transferred into the other strands; (3) an avalanche of quenching is induced among the strands; and (4) the central strand is quenched finally among the strands. The critical current values of the 7- and 7 × 7-stranded cables also are measured. These values are in good agreement with the predicted values based on the mutual inductance among the strands. It is concluded that the unbalance of the current distribution in the superconducting multistrands can be one of the promising causes for the degradation of the critical current value.     

Transformation behaviour with thermal cycling in NiTi alloys

The transformation behaviour of NiTi alloys were investigated by differential scanning calorimetry in order to reveal the effects of thermal cycles with the repetition of the transformation. The thermal cycles tend to lower the transformation temperature between the high and low temperature phases and to stabilize the intermediate phase during cooling to result in a two-stage transformation, while the reverse transformation during heating remains a one-stage transformation. Because these effects of the thermal cycles depend on the composition and the deformation, it is thought that defects play an intrinsic role in the complicated behaviour of NiTi alloys.     

Transmission Properties of Translucent Polycrystalline Alumina

Effects of residual pores and optical birefringence on transmission through translucent polycrystalline alumina have been studied with the Mie scattering theory. The in-line and total forward transmissions of the translucent polycrystalline alumina were simulated as a function of porosity, pore radius, and grain size. The model revealed that porosity has a significant effect on both the total forward scattering and the in-line transmission, whereas grain size affects only in-line transmission. The calculated transmittance is in good agreement with the experimental values. The in-line transmission gradually increased with a decrease in grain size, and the effect of birefringence on the total forward transmission is negligible in the visible spectrum. The total forward transmission in the visible spectrum is mainly governed by residual pores.     

Atomically flat diamond (111) surface formation by homoepitaxial lateral growth

A process of homoepitaxial growth of diamond (111) films by microwave plasma-enhanced chemical vapor deposition has been investigated characterizing areas by ex-situ atomic force microscopy. The evolution of surface morphology during a lateral growth of (111) diamond was visualized utilizing a mesa structure as a marker. Lateral growth forms atomically flat surfaces, which show atomically flat terraces over several hundred nm widths and single bilayer steps of (111) diamond.     

Evaporation performance of a new plate‐type heat exchanger with winding tubes on plate surfaces (estimation of performance of the heat exchanger)

A method for evaluating and predicting the performance of a newly developed plate‐type heat exchanger as an evaporator for water‐refrigerant systems such as chillers has been developed. The main component of the developed heat exchanger consists of plates packed together in a casing with winding tubes connected to both sides of the plates. Refrigerant flows inside the tubes, and water flows in the space between the plates. A herringbone‐like pattern is formed in this space by the cross sections of the winding tubes. The newly developed method estimates evaporation performance of the developed heat exchanger using new empirical correlations. There are correlations for heat transfer and pressure drop in winding‐tube banks on the water side, and correlation for the pressure drop on the refrigerant side. © 2004 Wiley Periodicals, Inc. Heat Trans Asian Res, 33(4): 245–257, 2004; Published online in Wiley InterScience ( www.interscience.wiley.com ). DOI 10.1002/htj.20009     

Advanced fabrication technologies of integrated-type structure for a-Si solar cells

This paper proposes a new advanced fabrication technology for a low-cost integrated-type a-Si solar cell. Integrated-type cells provide many advantages and have been industrialized with a laser patterning method. However, a higher throughput and more efficient patterning method was required for applying a-Si solar cells to a power generating system. Plasma CVM (Chemical Vaporization Machining) was first applied to advanced patterning because of its advantages of high speed and selectivity. In this method, a plasma generated under high pressure localizes near the wire electrode and concentrates reactive radicals. As a result, we achieved an etching rate of more than 1 μm/s and selective patterning of a 200 μm-wide a-Si layer in 1 s multiline patterning was also developed for large-area modules.