Micromechanisms of Tack of Soft Adhesives Based on Styrenic Block Copolymers

The tackiness of model soft adhesive layers based on styrene‐isoprene‐styrene block copolymers and a tackifying resin were investigated with a flat‐ended cylindrical steel probe. The contact between the probe and the adhesive was maintained for 1 s at a nominal pressure of 1 MPa before being detached at a constant velocity. The effect of resin content, probe velocity during debonding and temperature were systematically investigated. Failure was initiated by two main mechanisms: an interfacial cavitation at low debonding rates, giving relatively low adhesion energies, and a bulk cavitation process at higher debonding rates, which gave much higher adhesion energies. In both cases failure occurred at the end by interfacial detachment of fibrils. The characteristic probe velocity where the transition between these two mechanisms took place was controlled primarily by the linear viscoelastic properties of the adhesives. However, the important quantitative parameters obtained from a tack test, i.e., the maximum debonding stress and the adhesion energy, could not be predicted by the linear viscoelastic properties of these adhesives alone.     

Phylloquinone (vitamin K1) and dihydrophylloquinone content of fats and oils

Assessment of vitamin K (VK) dietary intakes has been limited by the incompleteness of VK food composition data for the U.S. food supply, particularly for VK-rich oils. The phylloquinone (VK-1) and 2′,3′-dihydrophylloquinone (dK) concentrations of margarines and spreads (n=43), butter (n=4), shortening (n=4), vegetable oils (n=6), and salad dressings (n=24) were determined by RP-HPLC with fluorescence detection. Each sample represented a composite of units or packages obtained from 12 or 24 outlets, which were geographically representative of the U.S. food supply. Butter, which is derived from animal fat sources, had less VK-1 compared to vegetable oil sources. The VK-1 and dK of the margarines and spreads increased with fat content and the degree of hydrogenation, respectively. In some margarines or spreads and in all shortenings, the dK concentrations were higher than the corresponding VK-1 concentrations. As the fat content of salad dressings increased, the VK-1 concentrations also increased. Fat-free foods had <1 μg/100 g of either form of the vitamin. No dK was detected in the salad dressings or oils tested. Some margarines, spreads, and salad dressings may be significant sources of vitamin K in the U.S. food supply.     

Synthesis of N,N-diethyl-N-{4-[(E)-(4-nitrophenyl)diazenyl]phenyl}amine via in situ diazotisation and coupling in supercritical carbon dioxide

The synthesis of azo dyes via a conventional aqueous-based diazotisation and coupling reaction requires the use of relatively high concentrations of mineral acids, which leads to high electrolyte concentrations in wastewater. Reported in this paper is an environmentally benign one-pot method for the synthesis of a nonionic azo dye, N,N -diethyl- N -{4-[( E )-(4-nitrophenyl)diazenyl]phenyl}amine, in supercritical carbon dioxide without using a mineral acid. The product yield increased significantly with temperature, with 91% theoretical yield afforded at 80 °C. The pressure of the system had little influence on product yield.     

An improved accelerated weathering protocol to anticipate Florida exposure behavior of coatings

A new accelerated weathering protocol has been developed which closely replicates the performance of automotive and aerospace coating systems exposed in South Florida. IR spectroscopy was used to verify that the chemical composition changes that occurred during accelerated weathering in devices with a glass filter that produced a high fidelity reproduction of sunlight’s UV spectrum matched those that occurred during natural weathering. Gravimetric water absorption measurements were used to tune the volume of water absorption during accelerated weathering to match that which occurred during natural weathering in South Florida. The frequency of water exposure was then scaled to the appropriate UV dose. A variety of coating systems were used to verify the correlation between the physical failures observed in the accelerated weathering protocol and natural weathering in South Florida. The new accelerated weathering protocol correctly reproduced gloss loss, delamination, cracking, blistering, and good performance in a variety of diverse coating systems. For automotive basecoat/clearcoat paint systems, the new weathering protocol shows significant acceleration over both Florida and previous accelerated weathering tests. For monocoat aerospace systems, the new weathering protocol showed less acceleration than for automotive coatings, but was still an improvement over previous accelerated tests and was faster than Florida exposure.     

Structural Studies and Valence Band Splitting Parameters in Ordered Vacancy Compound AgGa7Se12

The threefold absorption in the fundamental absorption region of the ternary chalcopyrite AgGa₇Se₁₂, an ordered defect compound of AgGaSe₂, is analyzed to elucidate the three closely spaced band gaps in its valence band due to the lifting of degeneracy of the Γ₁₅ level. Hopfield’s quasi cubic model is employed to extract the crystal-field and spin–orbit splitting parameters and the linear hybridisation of orbitals model for evaluating the percentage contribution of Ag d-orbital and Ga and Se p-orbitals to the p–d hybridization of orbitals. The observed optical properties are correlated with the structural parameters like deformation parameter, anion displacement and anion–cation bond lengths that are deduced from X-ray diffraction data. The compound films for the studies are prepared by a modified form of Gunther’s three temperature technique and the compositional analysis was done by energy dispersive analysis of X-rays. X-ray photoelectron spectroscopy confirms the compound formation while atomic force microscopic technique was used for surface morphological analysis. The electrical resistivity of these n-type semi-conducting films is assessed to be ~5 Ωm and the films are found to be photosensitive.     

Microwave dielectric properties of flexible butyl rubber–strontium cerium titanate composites

Butyl rubber–strontium cerium titanate (BS) composites have been prepared by hot pressing. The tensile tests show that the BS composites are flexible. The dielectric properties of the composites have been investigated at 1 MHz and 5 GHz as a function of ceramic contents. The composite with volume fraction 0.43 of ceramic filler has a dielectric constant (ε_r) of 11.9 and dielectric loss (tan δ) 1.8 × 10^?3 at 5 GHz. The measured values of ε_r are compared with the effective values calculated using different theoretical models. The thermal conductivity of the composites is found to increase with ceramic contents and reaches a value of 4.5 Wm^?1 K^?1 for maximum filler loading 0.43 volume fraction. The coefficient of thermal expansion of the composites decreases gradually with filler loading and reaches a minimum value of 30.2 ppm °C^?1 at a volume fraction 0.43. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

A cathode support structure for use in a magnetron oscillator experiment

A low temperature co-fired ceramic (LTCC) material system has been used to develop a protype field emission cathode structure for use in an experimental magnetron oscillator. The structure is designed for used with 30 gated field emission array (GFEA) die electrically connected through silver metal traces and electrical vias. To approximate a cylinder, the cathode structure (48 mm long and 13.7 mm in diameter) is comprised of 10 faceted plates which cover the GFEA dies. Slits in the facet plates allow electron injection. The GFEA die (3 mm × 8 mm) are placed in axial columns of 3 and spaced azimuthally around a cylindrical support structure in a staggered configuration resulting in 10 azimuthal locations. LTCC manufacturing techniques were developed in order to fabricate the newly designed cathode with seven layers wrapped to form the cylinder with electrical traces and vias. Two different cathode wrapping techniques and two different via filling techniques were studied and compared. Two different facet plate manufacturing techniques were studied. Finally, four different support stand configurations for firing the cylindrical structure were also compared with a square post stand having the best circularity and linearity measurements of the fired structure.     

An investigation of the effect of air addition during oil sand conditioning

Bitumen aeration was studied by flooding samples of medium grade oil sand with de‐ionized water under both ambient and high vacuum conditions. The samples were then agitated on a shaker table. Subsequent analysis revealed the presence or absence of an air gap in the sample container was the single most important factor in determining the overall bitumen recovery. Furthermore, samples that were flooded while under high vacuum produced slightly less bitumen compared to samples flooded at atmospheric pressure. This suggests that oil sand that is not under high vacuum when flooded with water contains some amount of indigenous air (see introduction) that would aid in bitumen flotation.     

Recycling of EPDM waste. II. Replacement of virgin rubber by ground EPDM vulcanizate in EPDM/PP thermoplastic elastomeric composition

Virgin ethylene propylene diene monomer (EPDM) rubber in a thermoplastic elastomeric blend of polypropylene (PP) and EPDM rubber was substituted by ground EPDM vulcanizate of known composition, after which the mechanical properties of the raw EPDM/waste EPDM/PP blends were determined. The ratio of the rubber content in the waste EPDM (r‐W‐EPDM) to the raw EPDM (R‐EPDM) in the blends was varied from 0 : 100 to 45 : 55. Attempts to replace higher amounts (>45%) of R‐EPDM by W‐EPDM failed because of processing difficulty. Although a drop in mechanical properties of the blends was observed at lower loadings of W‐EPDM, the properties showed improvement at intermediate W‐EPDM loadings. The R‐EPDM/W–EPDM/PP blends were found to be reprocessable. © 2001 John Wiley & Sons, Inc. J Appl Polym Sci 82: 3304–3312, 2001