Influence of fretting on the fatigue strength at the vise clamp-specimen interface

Fretting fatigue is one of the most important phenomena for inducing a significant reduction of fatigue strength and consequently, leading to unexpected failure accidents of the engineering structures even at very low stresses. In the present study, both plain and fretting fatigue tests with zero mean stress were carried out on two different types of steel, low-carbon steel and martensitic stainless steel, by means of a reversed bending fatigue testing machine. The drop in the fatigue strengths through fretting at vise clamp-specimen interface were significant for both tested steels. The fretting processes produced a reduction in fatigue strength of about 27% for low-carbon steel and 16% for martensitic stainless steel.     

NdCl_3·nTBP/MgCl_2-AlR_3催化体系合成丁二烯橡胶

探讨了以NdCl_3的磷酸三丁酯(TBP)溶液为主催化剂、烷基铝为助催化剂、MgCl_2为载体组成的Ziegler-Natta型催化体系引发丁二烯(Bd)聚合的某些规律。用AlEt_3作助催化剂,聚合物的顺1,4-结构含量仅为57％,反1,4-结构含量为42％;而以Al(i-Bu)_3作助催化剂,聚合物的顺1,4-结构含量为88％,反1,4-结构含量为11％。各种陈化体系中,以NdCl_3·nTBP/MgCl_2-Al(i-Bu)_3-Ip三元体系的催化活性最高,当Nd/Bd(摩尔比)为7×10~(-5)时,单体转化率达80％。低温聚合可获得高顺式、高分子量聚合物。     

污垢对冷水机组的影响

通过对两个工程实例的冷水机组测试结果对比分析，得出污垢对冷水机组造成了热阻增加，接热效果变差，制冷量减少以及制冷效率下降等严重后果，并推算出机组由此所带来的运行费用的增加。运行管理人员应该注意对机组加强清洗保养工作，以提高机组的经济运行水平。     

^125I,^131I诱发小鼠精子畸形发生率比较

本文选用 ICR 雄性小鼠,经腹腔分别注射不同剂量的~(125)I 及~(131)I,观察并比较它们对小鼠精子畸形发生率的影响及染毒后睾丸中放射性活度的变化。实验结果表明:(1)~(125)I 染毒后4—5周,0、185、370和555 kBq 各组精子畸形发生率分别为9.00‰、9.57‰、11.6‰及13.9‰;~(131)I 染毒后4—5周,上述各组精子畸形发生率分别为8.50‰、12.5‰、14.7‰和15.5‰;在相同注入量下,~(125)I 与~(131)I 诱发小鼠精子畸形发生率的差异各组均不显著(X~2检验,p>0.05)。(2)~(125)I、~(131)I 染毒后2h 至7天内,两者在睾丸中的放射性活度及变化规律相似,即在染毒后2h 达最高值,每克睾丸中~(125)I 和~(131)I 的放射性活度分别占初始注入量(370 kBq)的0.72％和0.50％,然后迅速下降,至一周时,仅分别占初始注入量的0.035％和0.011％。     

Thermal decomposition and micropore formation in PEK,PEEK and PES

At strain rates greater than about 10 the deformation of polymers is an adiabatic process which can lead to the generation of very high localized temperatures. These may be well in excess of the temperatures required for thermal decomposition of the polymer to occur. It is speculated that gaseous products arising from such decomposition may act as the source of microcavities and craze initiators. Experiments are described in which the thermal decomposition reaction parameters of polyetherketone, polyetheretherketone, and polysulphone are measured using differential scanning calorimetry and thermogravimetric analysis, and the decomposition products analysed by mass spectrometry. The results indicate that the proposed mechanism could act as a source of micropores with total pore volumes amounting to several per cent of the material volume.     

影响聚合物段塞流变性因素的研究

本文针对我国表面活性剂/聚合物驱油的实际,研究了石油磺酸盐(PS)、正丁醇(R_4OH)和矿化水对水解聚丙烯酰胺(HPAM)溶液流变性的影响。结果表明,PS对HPAM溶液流变性的影响与介质的矿化度有关:非矿化水介质中,PS对HPAM溶液性质的影响类似于无机盐,能降低HPAM溶液的表现粘度(η_α)和稠度系数(k);当系统中含有一定浓度矿化水时,PS却能升高系统的η_α和k值,降低流型指数(n),使系统的非牛顿性增强。在含有PS和矿化水的HPAM系统中加入R_4OH,系统的η_α和k值会有所增加。     

有杆泵抽油系统可靠性分析

抽油机井有杆果采油装置检泵故障数据的特点在于相邻两次检泵间隔之间的时间并非总是来自同一总体，可能有某种趋势的变化。通过对故障数据的趋势性检验，可验证其对某一随机过程模型的适应性，从而判定某一口井或某一批工况大致相同油井的运行可靠性，实现对生产井运行可靠性的定量评估。还通过实例说明了有杆泵抽油系统检泵故障数据的可靠性分析方法。     

线性规划模型的自动生成与求解

本文描述了《有色企业经济活动分析决策支持系统》模型库中线性规划模型的自动生成与求解系统的设计思想、方法及实现     

采用同调约束快速识别的有功校正控制计算

本文发展了文(5)提出的同调约束概念,将同调约束进一步分为正同调约束和反同调约束两组。文中提出了一种新的同调约束识别方法,不必增加任何计算便可快速识别出正反同调约束,显著地降低了解题规模。IEEE30节点样本网络的计算实例证实了本文方法的有效性。