关于本地传输网网络优化的探讨

根据长期工作经验,对现有网络存在的问题进行分析,提出对本地传输网网络优化的有关建议。     

关于海面无线传播模型的探讨

现有文献中一般都认为海面环境的无线传播模型近似于自由空间传播模型，但在实际测试中发现，自由空间模型预测值与实测值差别较大，不能很好地解释此类环境的信号传播。笔者根据多次海面覆盖测试的数据，分析并拟合出了新的海面传播模型。     

Preirradiation grafting of acrylic and methacrylic acid onto polyethylene films: Preparation and properties

The method of preirradiation grafting of acrylic acid and methacrylic acid onto polyethylene films was studied. The trapped radicals and hydroperoxides or diperoxides appeared to be able to induce graft polymerization. Mohr's salt was added to depress homopolymerization. The influences of crystallinity, dosage, and storage period on the grafting behavior were investigated from the viewpoint of practical application. At elevated temperature, the degree of grafting increased rapidly with reaction time initially, and then leveled off to the value of final percent grafting. Dosage and storage periods had greater extent of influence on the final percent grafting of LDPE than on that of HDPE. Electrical properties, transport properties, and mechanical properties were measured to compare the differences between acrylic-acid-and methacrylic-acid-grafted copolymer films. It was found that the properties of methacrylic-acid-grafted copolymer film was superior to those of acrylic-acid-grafted copolymer film, especially in electrical conductivity. The KOH diffusion test confirmed that grafting occurred not only on the surface but also in the interior of the polymer matrix, and the grafting is believed to proceed from the surface to the interior of the matrix.     

Traveling-wave piezoelectric linear motor Part I: the stator design.

A new type of piezoelectric linear motor incorporating a traveling wave has been developed. The linear motor is comprised of a stator and a carriage. The stator design, which consists of a meander-line structure and gear teeth mounted on the meander-line structure, is the focus of this article. The meander-line structure is constructed with bimorph actuators arranged in a line. These actuators are driven by two phased sets of alternating current (ac) in order to generate a traveling wave. The traveling wave is transferred to the gear teeth, by which the carriage is driven. Modeling of the stator is derived by use of a strain energy method. The performance of various materials is evaluated by analytical and experimental methods. The analytical and the experimental results are quite approximate. Modal analysis is investigated using ANSYS. Appropriate modes associated with ultrasonic levels of resonant frequency are selected to obtain desired motion and to enhance the output performance. Surface speed for various applied input voltage are studied and indicate a nearly linear relationship. The stator in combination with the carriage makes up the linear motor.     

Optimum power-saving method for power MOSFET width of DC/DC converters

An optimum power metal-oxide-semiconductor field effect transistor (MOSFET) width technique is proposed for enhancing the efficiency characteristics of switching DC-DC converters. By implementing a one-cycle buck DC-DC converter, it is demonstrated that the dynamic power MOSFET width controlling technique has a much improved power reduction whether the load current is light or heavy. The maximum efficiency of the buck converter is ~92% with a 3% efficiency improvement for the heavy load condition. The efficiency is further improved by ~16% for the light load condition as a result of the power reduction from the large power MOSFET transistors. Also proposed is a new error-correction loop circuit to enable a better load regulation than that of previous designs. Compared with the adaptive gate driver voltage technique, the optimum power MOSFET width can achieve a significant improvement in power saving. It is also superior to the low-voltage-swing MOSFET gate drive technique for switching DC-DC converters     

加油站油品用体积交接存在的问题及建议

叙述了目前加油站在实行按任意温度下的体积交接，由于未考虑油品体积随温度、压力、密度的变化，出现了零售损耗很大的问题。建议加油站在现阶段采用“准标准体积”交接；在由体积转换为质量计算加油站损溢时，使用油库当月发出的平均密度；当财会核销损溢时，不使用盘存的体积和固定密度进行计算的方法，而使用实际盘点的质量数，以真实反映加油站的当期损溢。     

猪场沼气工程改造技术研究

一、概况南平市种猪场位于延平区浆甲村 ,距市区 13km ,地处 316国道旁 ,面临沙溪口库湾边。年存栏猪760 0头 ,其中母猪 60 0头 ,后备种猪 2 5 0 0头 ,商品猪 4 5 0 0头 ,是闽北集种猪、商品猪生产及科研繁育于一体的副食品基地之一。该场日排猪粪便污水约140t,未建沼气工程前 ,直接排入水库 ,严重污染水体。1999年 ,种猪场采用厌氧发酵技术 ,处理猪粪便污水 ,兴建 4× 2 0 0m3沼气工程 ,技术落后 ,基本属于农村户用水压式沼气池的简单放大 ,猪粪便污水直接进入厌氧发酵池 ,出水直接排入水库。工程设计的主要问题是 :1 不设前处理装置 ,冲洗…     

Enhancement of islanding-detection of distributed generation systems via wavelet transform-based approaches

In this paper, a wavelet transform-based approach is proposed to detect the occurrence of islanding events in distributed generation systems. Thanks to time–frequency localization capabilities exhibited by wavelet transform, the approach embedded with this transform technique has grasped the appearance of the islanding event in a highly effective manner. Moreover, for those regions which are in need of a better visualization, the proposed approach would serve as an efficient aid such that the mains power disconnection can be better distinguished. To validate the feasibility of this approach, the method has been validated through several scenarios. Test results supported the effectiveness of the method for the application considered.     

Plastic deformation and fracture of binary TiAl-base alloys

The mechanical behavior of binary TiAl alloys containing 46 to 60 at. pct Al has been studied in bulk materials preparedvia rapid solidification processing. Bending and tensile tests were carried out at room temperature as a function of Al concentration. A few alloys were also tested from liquid nitrogen temperature to ∼ 1000°C. Deformation substructures were studied by analytical transmission electron microscopy and fracture modes by scanning electron microscopy (SEM). It was found that both microstructure and composition strongly affect the mechanical behavior of TiAl-base alloys. A duplex structure, which contains both primary y grains and transformedγ/α ₂ lamellar grains, is more deformable than a single-phase or a fully transformed structure. The highest plasticities are observed in duplex alloys containing 48–50 at. pct Al after heat treatment in the center of theγ + α phase field. The deformation of these duplex alloys is facilitated by 1/2[110] slip and {111} twinning, but very limited superdislocation slip occurs. The twin deformation is suggested to result from a lowered stacking fault energy due to oxygen depletion or an intrinsic change in chemical bonding. Other factors, such as grain size and grain boundary chemistry and structure, are important from a fracture point of view. The results on the deformation and fracture modes as a function of test temperature are also discussed.     

Peripheral nerve injury as a complication from orthopedic operation

We report a case of pulmonary carcinosarcoma. Surgery is required for this rare mixed type, biphasic tumor. It is generally considered to be a malignant formation issuing from a single cell line but with a two-way differentiation into epithelial and conjunctive components. There is a differentiation continuum between spindle-cell carcinomas (also called monophasic sarcomatoid carcinoma) and carcinosarcoma (or biphasic sarcomatoid carcinoma) leading to debate concerning the immunohistochemical and ultrastructural features.