Improvement of AlGaInP light emitting diode by sulfide passivation

The brightness of AlGaInP light emitting diodes (LEDs) has been raised by a factor of 1.12 at 20 mA by sulfide passivation. Meanwhile, the sulfide also can decrease leakage current of AlGaInP LEDs at -2 V to nearly one thousandth of that in the as-fabricated device. The possible causes for the brightness increase of AlGaInP LEDs after sulfide treatment including surface roughness, reduction of Fresnel loss, and effective injection of carriers were demonstrated.     

Clinical study in epidural injection with lappaconitine compound for post-operative analgesia

In this study, the effect and side-effect of epidural injection with lappaconitine compound for post-operative analgesia was observed. One hundred and twenty patients were randomly divided into 4 groups. Lappaconitine compound (LB) consisted of 12 mg of lappaconitine and 22.5 mg of bupivacaine, was given to group A (the group of observation), and lappaconitine 12 mg, bupivacaine 22.5 mg and morphine 2 mg to group B, C and D respectively for control. All were given by epidural injection with single blind method during post-operative pain of incision operation. Result showed that the initiating of analgesia was quicker in group A and C than that in group B and D, and the efficacy was group D > A > C > B. There was significant difference between group A and B in the above two parameters, P < 0.01 and P < 0.05. The analgisia maintenence time of single injection was D > A > B > C, that of group D was significantly longer than that of group A (P < 0.01). It indicated that the epidural injection with LB was more rapid and potent than that with lappaconitine alone in post-operative analgesia, and the former had no side-effect, it was safer than morphine.     

离子注入中污染的产生及防护

本文概述了离子注入过程中污染产生的原因和防止污染的措施，特别强调了对微粒污染和金属污染的防护以满足ＵＬＳＩ加工对离子注入的要求。     

Improved Yen-Joye's authenticated multiple-key agreement protocol

An authenticated multiple-key agreement protocol is proposed. The protocol is not only secure against the unknown-key attack but also more efficient than other protocols.     

Fabrication of 1.55 μm VCSELs on Si using metallic bonding

Using AuGeNiCr multilayered metals as the wafer bonding medium, long-wavelength GaInAsP/InP vertical cavity surface emitting lasers employing Al-oxide/Si as the upper and lower distributed Bragg reflectors were fabricated on Si substrate with the bonding interface formed outside the vertical cavity surface emitting laser cavity. Laser emission at 1.545 μm was measured under pulsed operations near room temperature. The low-temperature metallic bonding process demonstrates a great potential in device fabrication     

A fully soft-switched extended-period quasi-resonantpower-factor-correction circuit

This paper presents the design criteria, procedure, and implementation of a soft-switched power-factor-correction (PFC) circuit based on the extended-period quasi-resonant (EPQR) principles. All power electronic devices including switches and diodes in the circuit are fully soft switched. The design method is demonstrated in a prototype circuit. The operating principles are confirmed with computer simulation and experimental results. A comparison of the EP-QR operation and zero-voltage-transition (ZVT) pulse-width modulation (PWM) method     

Coplanar waveguide-fed uniplanar bow-tie antenna

The design of coplanar waveguide (CPW)-fed bow-tie antenna for the 2.4-GHz ISM band is described. A coplanar waveguide-to-coplanar strips (CPW-to-CPS) balun is used to obtain the balanced feed line for the printed bow-tie. An analysis method based on the mixed potential integral equation method is used to characterize the input characteristics of the bow-tie antenna. The numerical results obtained are in good agreement with the experimental data. Through experiments with bow-tie antennas of various extended angles, the bow-tie antenna with a 90° extended angle exhibits the widest bandwidth in the desired frequency band which has a bandwidth of 17% for a VSWR <1.5:1     

Color image retrieval based on hidden Markov models

In this correspondence, a new approach to retrieving images from a color image database is proposed. Each image in the database is represented by a two-dimensional pseudo-hidden Markov model (2-D PHMM), which characterizes the chromatic and spatial information about the image. In addition, a flexible pictorial querying method is used, by which users can paint the rough content of the desired images in a query picture. Image matching is achieved by comparing the query picture with each 2-D PHMM in the database. Experimental results show that the proposed approach is indeed effective.     

Handling multimedia information with VLSI

Identifies the basic technological components of multimedia communications. Among these technologies, multimedia processing and transmission already benefit heavily from VLSI advances. in fact, these two technologies could not have matured without special-purpose VLSI chips. We have examined basic processing required in these technologies and some VLSI architectures. The focus has been on standard-compliant VLSI chips, because the eventual goal of communications is to allow everyone to reach others without constraints. There are still a number of evolving standards, which means that we might witness yet another wave of VLSI chips for multimedia communications