Solaris2.X操作系统上NFS的环境配置

本文描述了Ｓｏｌａｒｉｓ２．Ｘ操作系统上网络文件系统ＮＦＳ的特性及其环境配置，介绍了如何建立了ＮＦＳ服务器和ＮＦＳ客户机，从而实现了远程文件系统资源共享。     

机床工具产品色彩造型初探

本文针对我国机床工具产品色彩设计的现状,结合具体实例,对色彩造型的实质做了初步的探讨。分析了色彩造型和色彩装饰两种设计观和实践效果;以色彩与形状关系及作用的论证为引,论述色彩造型的三大功能作用。并提出可供机床工具产品色彩设计参考的具体设计方法和手段。     

Analysis of thermal instability in multi-finger power AlGaAs/GaAsHBT's

A new theory is developed in this paper to explain the collapse of current gain in multi-finger power AlGaAs/GaAs Heterojunction Bipolar Transistors (HBT's). The reasons behind this unwanted phenomenon are fully clarified using a simple model to investigate the thermo-electrical interaction between the fingers. The existence of multi-value equilibrium points in model's constitutive equations is shown to be the necessary condition for the collapse of current gain to appear. For a N-finger device, N different patterns of collapse exist. The criterion to select the global stable pattern is given. The method has been used to predict the collapse in AlGaAs/GaAs HBT's and the agreement is excellent. The method also predicts that the collapse can happen far earlier than is normally expected in multi-finger high-power devices. The influence of ballasting resistance and thermal resistance is also investigated     

彩色PDP用玻璃基板

本文讨论了彩色ＰＤＰ现用钠钙玻璃的热稳定性，指出由于这种玻璃在热处理过程中易变形和收缩，因而不适合作大面积彩色ＰＤＰ基板材料，介绍了彩色ＰＤＰ基板玻璃的制造方法和特点。最后介绍了日本旭硝子公司和美国康宁公司各自为彩色ＰＤＰ新开发的玻璃基板材料ＰＤ２００和ＣＳ２５。     

晶须取向对SiCw／Al复合材料切削表面质量的影响

切削与晶须取向方向间的夹角对ＳｉＣｗ／Ａｌ复合材料切削表面质量有很大影响。当切削角为４５°时，晶须拔出和转动现象均较少，复合材料切削表面粗糙度最低。当切削角为１３５度时，晶段转动造成的撕裂破坏程度很大，复合材料切削表面粗糙度最大。     

对洪水分级的浅见

洪水的等级划分应考虑流量、水位、防洪能力及灾害等因素,综合这些因素把洪水分成5个等级。1、2级洪水,洪水流量小,水位低,基本无灾;3级洪水,洪水流量较大或水位较高,有一定灾害;4级洪水,为大洪水或高水位,有较大灾害;5级洪水,为特大洪水或高水位,灾情严重。     

新的钢铁工业结构与铁矿资源条件的能源优化模型研究

发展我国钢铁工业，资源和能源已经成为两个重要的制约因素。到本世纪末，我国钢产量达1．2亿t，所需资源必须有部分进口。本文论述了新的钢铁企业模型结构及采用部分进口废钢和铁矿石的能源优化问题。     

钢管内径光电检测装置

介绍了一种检测细长钢管内径的光电检测装置。该装置利用线阵ＣＣＤ作传感器，采用８０３１单片机作为主控制。     

Air bearing design, optimization, stability analysis andverification for sub-25 nm flying

Three sub-25 nm fly height sliders are presented for near contact recording. The designs are geared towards the goal of achieving 10 Gb/in ² areal density. The optimization procedure presented shows promise for facilitating achievement of this goal. The dynamic simulations show the stability of these designs when disturbed from their steady state conditions     

微量Ag对CP276合金性能和组织的影响

研究添加不同含量的Ａｇ对ＣＰ２７６合金的拉伸性能和时效组织的影响。对拉伸强度、延伸率测试及透射电镜观察表明：０．１１ｗｔ％加入可促进Ｔ１相析出，使合金强度值升高；０．３５ｗｔ％Ａｇ的加入可在时效前期生成富Ａｇ、Ｍｇ的稳定的ＧＰ区，从而降低合金中Ｃｕ的固溶度，阻碍Ｔ１相析出，时效后期，ＧＰ区分解，生成大量Ｔ１相，使合金强度值显著升高。