Functionality of strawberry powder on frozen dairy desserts

This study investigated the potential use of freeze‐dried strawberry powder as a stabilizer in frozen dairy desserts. Five different dessert mixes were developed that contained 0%, 2.5%, 3%, 3.5%, and 4% strawberry powder. An additional dessert using strawberry extract was prepared to differentiate the effects of dietary fiber from the effect of polyphenols on sample properties. The rheological and physical characteristics of dessert mixes, fresh dessert, and stored dessert were studied. The addition of strawberry powder to dairy desserts caused an increase in the mix viscosity and a decrease in hardness and meltdown values. Complete avoidance of meltdown was achieved with the addition of 3% or greater amount of strawberry powder. The viscosity of mixes was enhanced due to the increase of total solids in the serum phase and the formation of hydrated and gel‐like networks in the presence of cellulosic material, pectin, and calcium. The increase in viscosity and unfrozen water with the addition of strawberry powder also caused a reduction in ice crystallization, which resulted in softer and more stable desserts over time.     

Solution Blow Spinning of Food‐Grade Gelatin Nanofibers

The primary advantage of nanofibers over larger diameter fibers is the larger surface area to volume ratio. This study evaluated solution blow spinning (SBS) processing conditions for obtaining food‐grade gelatin nanofibers from mammalian and fishery byproducts, such as pork skin gelatins (PGs) and high molecular weight fish skin gelatin (HMWFG). HMWFG had a highest intact collagen structure compared to PGs. PGs with different Bloom values, solution viscosities, and surface tensions were compared with HMWFG for their ability to produce nanofibers through SBS. Only HMWFG fibers were obtained irrespective of processing conditions, which looked like fluffy cotton candy. HMWFG nanofibers had round morphologies with a narrower diameter distribution and lower average fiber diameter (AFD) under medium gelatin concentrations, medium air pressures, and medium feed rates. The highest glass transition temperature (T_g) values were obtained at medium concentrations, medium air pressure, and either high or low feed rate. The thinnest HMWFG nanofibers with an AFD of 80.1 nm and the highest T_g value of 59.0 °C could be formed by combining a concentration of 17.6% (w/v), an air pressure of 0.379 MPa, and a feed rate of 0.06 mL/min from the response surface analysis. HMWFG Brunauer, Emmett, and Teller surface area increased from 221 to 237 m²/g, indicating their potential applicability for active compound carrier.     

Biocompatibility and characteristics of chitosan/cellulose acetate microspheres for drug delivery

In this work, chitosan/cellulose acetate microspheres (CCAM) were prepared by the method of W/O/W emulsion with no toxic reagents. The microspheres were spherical, free flowing, and non-aggregated, which had a narrow size distribution. More than 90% of the microspheres had the diameter ranging from 200 to 280 μm. The hemolytic analysis indicated that CCAM was safe and had no hemolytic effect. The implanted CCAM did not produce any significant changes in the hematology of Sprague-Dawley (SD) rats, such as white blood cell, red blood cell, platelet, and the volume of hemoglobin. In addition, the levels of serum alanine aminotransferase, blood urea nitrogen, and creatinine had no obvious changes in SD rats implanted with CCAM, surger thread, or normal SD rats without any implantation. Thus, the CCAM had good blood compatibility and had no hepatotoxicity or renal toxicity to SD rats. Furthermore, CCAM with or without the model drug had good tissue compatibility with respect to the inflammatory reaction in SD rats and showed no significant difference from that of SD rats implanted with surgery thread. CCAM shows promise as a long-acting delivery system, which had good biocompatibility and biodegradability.     

Soft‐switching converter with low circulating current and wide range of ZVS turn‐on

In this paper, a new hybrid dc–dc converter with low circulating current within the freewheeling interval, wide range of zero‐voltage switching and reduced output current ripple is presented. The proposed hybrid circuit includes two three‐level pulse‐width modulation converters and a series resonant converter with the shard lagging‐leg switches. Series resonant converter is operated at fixed switching frequency (close to series resonant frequency) to extend the zero‐voltage switching range of lagging‐leg switches. The output of series resonant converter is connected to the secondary sides of three‐level converters to produce a positive rectified voltage instead of zero voltage. Hence, the output inductances can be reduced. The reflected positive voltage is used to decrease the circulating current to zero during the freewheeling interval. Therefore, the circulating current losses in three‐level converters are improved. Finally, experiments are presented for a 1.44 kW prototype circuit converting 800 V input to an output voltage 24 V/60A. Copyright © 2015 John Wiley & Sons, Ltd.     

A new parallel ZVS converter with less power switches and low current stress components

A new direct current (DC)/DC converter with parallel circuits is presented for medium voltage and power applications. There are five pulse‐width modulation circuits in the proposed converter to reduce current stress at low voltage side for high output current applications. These five circuits share the same power switches in order to reduce switch counts. To reduce the converter size, conduction loss, and voltage stress of power semiconductors, the series connections of power metal‐oxide‐semiconductor field‐effect transistor (MOSFET) with high switching frequency instead of insulated gate bipolar transistor (IGBT) with low switching frequency are adopted. Thus, the voltage stress of MOSFETs is clamped at half of input voltage. The switched capacitor circuit is adopted to balance input split capacitor voltages. Asymmetric pulse‐width modulation scheme is adopted to generate the necessary switching signals of MOSFETs and regulate output voltage. Based on the resonant behavior at the transition interval of power switches, all MOSFETs are turned on under zero voltage switching from 50% load to 100% load. The circuit configuration, operation principle, converter performance, and design example are discussed in detail. Finally, experimental verifications with a 1.92 kW prototype are provided to verify the performance of the proposed converter. Copyright © 2015 John Wiley & Sons, Ltd.     

Controllable fabrication and properties of polypropylene nanofibers

Thermoplastic nanofibers in yarn form were prepared by melt extrusion of immiscible blends of cellulose acetate butyrate (CAB) and thermoplastic polymers and subsequent removal of the CAB matrix. Isotactic polypropylene (iPP) nanofiber, with diameters ranging from 75 to 375 nm, were made by using CAB/iPP blends, with a ratio of 97.5–2.5, and a hot‐drawn ratio of 25 in a twin‐screw extruder. Dispersion of iPP in CAB and shear and elongational deformation are major factors to result in nanosized fibers. The spheres and nanofibers with different diameters of iPP dispersed phases in the CAB matrix can be well controlled by changing the flow field and the blend ratio. Differential scanning calorimeter and wide angle X‐ray diffraction results showed that the nanofibers had lower crystallinity and crystallite thickness compared with bulk iPP. The atomic force microscopy images presented the well‐defined nanofiber morphology and the excellent manipulability of single iPP nanofiber separated from a bundle of iPP nanofibers. POLYM. ENG. SCI., 47:1865–1872, 2007. © 2007 Society of Plastics Engineers