Half-bridge inverter using 4H-SiC gate turn-off thyristors

This paper reports on the first demonstration of a half-bridge power inverter constructed from silicon carbide gate turn-off thyristors (GTOs) operated in the conventional GTO mode. This circuit was characterized with input bus voltages of up to 600 VDC and 2 A (peak current density of 540 A/cm²) with resistive loads using a pulse-width modulated switching frequency of 2 kHz. We discuss the implications of the thyristor's electrical characteristics and the circuit topology on the overall operation of the half-bridge circuit. This work has determined the conservative critical rate of rise value of the off-state voltage to be 200 V/μs in these devices     

Incremental transmission loss allocation under pool dispatch

Incremental transmission loss analysis has been used for decades, but recent interest in its application to loss allocation calls for new in-depth results. This paper demonstrates that, for incremental methods to be applied correctly in loss allocation, it is first necessary to specify the load distribution and loss supply strategies. Incremental loss allocation among bus power injections is shown to be arbitrary and, therefore, open to challenge as discriminatory. Loss allocation is possible among incremental loads and/or generators, but the proportion of the total losses assigned to either one is arbitrary. Unique, nonarbitrary incremental loss allocations are however possible among the "equivalent" incremental bilateral exchanges between generators and loads. From these basic components it is possible then to calculate the allocation among generators or loads in any specified proportion. The main results, although developed initially for small increments, are extended to large variations. Finally, a general incremental loss allocation algorithm is developed and tested     

约旦坦努尔RCC坝达到高标准

坦努尔坝是约旦的第一座RCC坝。该坝RCC铺筑采用斜层施工，提高工数50％。大坝上游面，下游台阶，阶梯式溢洪道，止水面以及RCC与坝肩石灰岩的交界面均采用GE－RCC。质量控制测试数据表明，该坝达到了国际大坝委员会会刊不久将发表的RCC坝质量标准的优良等级。     

Modern Aluminum and Magnesium Alloys and Composite Materials Based on Them

Aluminum and magnesium alloys are the base structural materials in aircraft and spacecraft engineering. The main stages of the development and introduction of light alloys are described.     

Influence of Edible Films upon the Moisture Loss and Microstructure of Dietetic Sucrose-Free Sponge Cakes during Storage

The kinetics of changes in the bound water content in dietetic sucrose-free sponge cakes (DC) during storage was investigated. The effect of edible films of polymyxan, pectin, xanthan, and carboxymethylcellulose upon this kinetics was also investigated. The quantitative changes in both states of water (slightly bound water and strongly bound water) were registered by combined dynamic analysis (thermogravimetry analysis, TGA, and differential thermal analysis, DTA). The moisture changes in DC crumb were analyzed by drying out to constant mass. The rate constants were determined according the equation q = q_oe^-kt. The values of rate constants 'k', in day^-1, concerning the different edible films were as follows: for crumb moisture is (8.00 ≤ k ≤ 12.47) × 10^-3, for bound water is (3.07 ≤ k_w ≤ 6.26) × 10^-2, for slightly bound water is (4.22 ≤ k₁ ≤ 8.49) × 10^-2 and for strongly bound water is (2.02 ≤ k₂ ≤ 5.62) × 10^-2 as compared to 18.53 × 10^-3, 7.16 × 10^-2, 9.04 × 10^-2, and 5.36 × 10^-2 in the uncovered DC, respectively. The best water-retaining effect in respect to crumb moisture during storage was ascertained in the use of polymyxan and xanthan films. The lowest rate constant values for bound water and its two states were measured for DC covered with pectin. The relation between the kinetics of both bound water states during storage and ageing of the crumb of DC covered with different edible films and the crumb microstructure was represented. By means of scanning electron microscope was read the smallest change in crumb microstructure of pectin-covered DC on the sixth day of storage.     

Crisis phenomena upon evaporation in grid capillary and porous coatings and arterial structures of heat pipes

The article presents the results of experimental investigations of critical (limit) heat fluxes upon evaporation on porous coatings, and it substantiates the physical model of the process.Translated from Inzhenerno-Fizicheskii Zhurnal, Vol. 49, No. 4, pp. 607–614, October, 1985.     

Structure and composition of guanidine acrylate, guanidine methacrylate, their homopolymers, and copolymers with diallyldimethylammonium chloride

Structures and compositions of the monomers guanidine acrylate and guanidine methacrylate, their homopolymers, and copolymers with diallyldimethylammonium chloride enriched in acrylate comonomer units were determined. It was shown that ampholytic copolymers, owing to their ionic nature, contained comonomeric guanidine acrylate or methacrylate units and diallyldimethylammonium chloride units, as well as the acrylate comonomer with the diallyl counterion and polymeric acrylate and diallyl ion pairs. It follows from IR and ¹H NMR data that guanidine methacrylate has the same structure (with two hydrogen bonds) in the solid state and in solutions. Guanidine acrylate structures in the solid state and in dimethylsulfoxide are identical and analogous to guanidine methacrylate structure in this solvent. In water, the guanidine acrylate structure has another type of hydrogen bonding (with one hydrogen bond, where the proton is shifted toward the guanidine group). These features of hydrogen bonding of guanidine acrylate and guanidine methacrylate are also retained in their homopolymers and copolymers with diallyldimethylammonium chloride. It was shown that the thermal stability of the copolymers was higher than that of their homopolymers, confirming the formation of intramolecular ion pairs of oppositely charged units of ampholytic copolymers. Moreover, the thermal stability of guanidine methacrylate-diallyldimethylammonium chloride copolymers is higher than that of guanidine acrylate-diallyldimethylammonium chloride copolymers.     

On the nonuniformity of a capillary flow

It is established that the capillary rise of a liquid has an oscillatory character, in contrast to the commonly accepted opinion that a vertical capillary is filled at a monotonically varying velocity. The value of the tangential shear stress arising in an ascending liquid is evaluated for ethyl alcohol and distilled water.     

Experimental Electronuclear Setup at the Institute of Theoretical and Experimental Physics

The purpose and current construction status, at the Institute of Theoretical and Experimental Physics, of an experimental electronuclear setup, combining a pulsed proton linear accelerator (36 MeV, 0.5 mA) and a subcritical blanket thermal-power assembly 100 kW, are discussed. The main equipment is already available or is being built in industry. The setup can be used to investigate the dynamics of the interaction of a linac–driver and a subcritical reactor and problems concerning the accelerator–driver and the target–blanket assembly. The proton beams and neutron fluxes will be used for applied purposes. In the future it will be possible to increase substantially the current and energy of the proton beam.