Surface tension as a controlled variable in mechanical dishwashing

Using a continuous, in-line, nondestructive technique based on the maximum bubble pressure method, the surface tension of the wash water in a mechanical dishwashing machine has been monitored. This technique has enabled surface tension to be used as a controlled variable, providing feedback to regulate the amount of surfactant added. Assuming the mechanical force of the water spray is adequate to remove bound soil from the dish surface, the food soil may be titrated against surfactant, providing an indirect indication as to when the dishes are clean. This technique also could be applied to a recirculated wash solution for in-place cleaning.     

Improvement in hydrolytic procedure for GLC determination of non-indolyl glucosinolates in rapeseed as isothiocyanates

Some methods determine the non-indolyl glucosinolates content in rapeseed as their hydrolysates: the isothiocyanates and the oxazolidinethiones. These methods in their present form underestimate the amount of the glucosinolates content. In this investigation, a modified method was developed to give a better quantitative estimate, indicating a glucosinolate level five times that obtained by a typical existing method.     

AN ASSESSMENT OF CRACK CLOSURE AND THE EXTENT OF THE SHORT CRACK REGIME IN Q1N (HY80) STEEL

Abstract— The paper addresses some aspects of the differences in fatigue crack growth rate behaviour and threshold values obtained for long through-cracks, short through-cracks and surface cracks. Attention is focused on plasticity induced closure in the wake behind the growing crack tip. For long cracks at high K _max, closure is found to depend in a linear manner on K _max, i.e. K _op, increases with the size of the monotonic plastic zone. Closure increases at low δ K and this is primarily a consequence of the load shedding procedure. If short through-cracks are prepared by machining specimens containing long cracks, a substantial part of the plastic wake is removed and this can produce marked effects on the closure contribution during subsequent growth. The length of crack "closed" in a long crack threshold test was found to be of the order of 1 mm. Cracks less than this length exhibited "short crack" behaviour: greater than this length, they behaved as "long cracks", with plastic wake effects apparently fully operative. Small surface cracks exhibit "long crack" behaviour at lengths as short as 0.2 mm and reasons for this are discussed.     

Modeling and assimilation of root zone soil moisture using remote sensing observations in Walnut Gulch Watershed during SMEX04

Soil moisture status in the root zone is an important component of the water cycle at all spatial scales (e.g., point, field, catchment, watershed, and region). In this study, the spatio-temporal evolution of root zone soil moisture of the Walnut Gulch Experimental Watershed (WGEW) in Arizona was investigated during the Soil Moisture Experiment 2004 (SMEX04). Root zone soil moisture was estimated via assimilation of aircraft-based remotely sensed surface soil moisture into a distributed Soil-Water-Atmosphere-Plant (SWAP) model. An ensemble square root filter (EnSRF) based on a Kalman filtering scheme was used for assimilating the aircraft-based soil moisture observations at a spatial resolution of 800 m × 800 m. The SWAP model inputs were derived from the SSURGO soil database, LAI (Leaf Area Index) data from SMEX04 database, and data from meteorological stations/rain gauges at the WGEW. Model predictions are presented in terms of temporal evolution of soil moisture probability density function at various depths across the WGEW. The assimilation of the remotely sensed surface soil moisture observations had limited influence on the profile soil moisture. More specifically, root zone soil moisture depended mostly on the soil type. Modeled soil moisture profile estimates were compared to field measurements made periodically during the experiment at the ground based soil moisture stations in the watershed. Comparisons showed that the ground-based soil moisture observations at various depths were within ± 1 standard deviation of the modeled profile soil moisture. Density plots of root zone soil moisture at various depths in the WGEW exhibited multi-modal variations due to the uneven distribution of precipitation and the heterogeneity of soil types and soil layers across the watershed.     

The hot blow forming of AZ31 Mg sheet: Formability assessment and application development

The hot blow forming of magnesium sheet offers significant opportunity for forming complex, lightweight parts for automotive applications. This paper characterizes the elevated-temperature formability of AZ31 magnesium sheet materials and the effect of processing conditions on the performance of these materials. In addition, magnesium sheet application development at General Motors Corporation is reviewed.     

Numerical simulation of typical contact situations of brake friction materials

In the paper, a model typical for contact situations of automotive brakes is established based on the method of movable cellular automata. The processes taking place at local contacts in an automotive brake system are analysed. Based on microscopic and micro-analytical observations, the following contact situations were simulated: (i) a couple of ferritic steel against pearlitic steel, both covered by an oxide layer mixed with graphite nanoparticles and (ii) the same situation but without oxide layers. The results of calculated mean coefficients of friction of the oxide-on-oxide contact correspond well to expected values for a real braking system, whereas steel-on-steel contact are twice as high. This allows one to make some conclusions; for example, oxide formation will take place more quickly than friction layer elimination, and finally this is responsible for the stabilisation of the coefficient of friction.     

Simulation of Strength Distribution in Ground Ceramics by Incorporating Residual Stress Effect

Strength of ground ceramics may be affected by residual stress as well as surface flaws induced by grinding. Strength prediction for ground ceramics is convenient for mechanical design of ceramic components. In this article, a numerical procedure based on fracture mechanics was proposed to estimate strength distribution of ground ceramics by considering grinding-induced residual stress. Bending strength and residual stress of ground ceramics were measured for three grinding-conditions. By comparison of simulated results with experimental ones, it was revealed that strength characteristics in experiments were well simulated by using the proposed procedure.     

Fuzzy Learning of Talbot Effect Guides Optimal Mask Design for Proximity Field Nanopatterning Lithography

Processing methods used in photonics and nanotechnology possess many limitations restricting their application areas such as high cost, inability to produce fine details, problems with scalability, and long processing time. Proximity field nanopatterning is a lithography method which surpasses these limitations. By using interference patterns produced by a two-dimensional phase mask, the technique is able to generate a submicron detailed exposure on a millimeter-size slab of light sensitive photopolymer, which is then developed like a photographic plate to reveal three-dimensional interference patterns from the phase mask. While it is possible to use simulations to obtain the interference patterns produced by a phase mask, realizing the mask dimensions necessary for producing a desired interference pattern is analytically challenging due to the intricacies of light interactions involved in producing the final interference pattern. An alternative method is to iteratively optimize the phase mask until the interference patterns obtained converge to the desired pattern. However, depending on the optimization technique used, one either risks a significant probability of failure or requires a prohibitive number of iterations. We argue that an optimization technique that is to take advantage of the physics of the problem using machine learning methods (here fuzzy learning) can lead to competent mask design. This technique is described in this letter.