Photolysis of poly(3-buten-2-one), poly(4,4-dimethyl-1-penten-3-one), and poly(3-methyl-3-buten-2-one) in the presence of oxygen

Photolysis of poly(3-buten-2-one) (PMVK), poly(4,4-dimethyl-1-penten-3-one) (PBVK), and poly(3-methyl-3-buten-2-one) (PMIK) were carried out in dioxane under oxygen or nitrogen bubbling. The main chain degradations of PBVK and PMIK were quenched and polymeric peroxides were produced. The heat treatment of the polymer irradiated in the presence of oxygen promoted the degradation. The photodegradation of PMVK was enhanced in the presence of oxygen.     

Stable transverse mode oscillation in planar stripe laser with deep Zn diffusion

The guiding mechanism in a planar stripe laser with deep Zn diffusion under the lasing conditions was investigated both theoretically and experimentally. The conditions necessary to realize refractive index guiding depend on a combination of electron and hole concentrations. The lasers under refractive index guiding, whose stripe width is less than twice the diffusion length, with an adequate combination of electron and hole concentrations, show stable fundamental transverse mode oscillation up to three times the threshold current level.     

Marked particle size and support effect of Pd catalysts upon the direct decomposition of nitric oxide

The catalytic behavior of beryllia-supported Pd catalyst for the direct decomposition of NO was compared with that of silica supported one. The TOF of NO decomposition was one order of magnitude larger in the case of Pd/BeO. Over Pd/SiO₂, the TOF was increased with the increase of the Pd particle size. On the contrary, over Pd/BeO smaller Pd particles exhibited higher TOF for NO decomposition suggesting some strong electronic or structural interaction between Pd and beryllia. TPD spectra of NO(a) over reduced catalysts indicated that NO was adsorbed on Pd/SiO₂ more strongly than on Pd/BeO, and dissociation of NO(a) was easier on the former catalyst. FT-IR spectra of adsorbed NO at room temperature followed by the evacuation at elevated temperatures confirmed this. TPD spectra of O₂ desorbed from oxidized surface indicated that adsorption strength of O(a) is one of the most important factors to determine the catalytic activity of NO decomposition over supported Pd catalysts.     

GaAs varactor diode for u.h.f. t.v. tuners

The design and fabrication of a GaAs varactor diode for u.h.f. t.v. tuners were carried out using a GaAs double epitaxial layer. The capacitance ratio of diode. C3/C25, is 6.0 and the series resistance at 470 MHz is 0.24 ?. These characteristics are much better than those of an Si diode and well satisfy the requirements for t.v. tuners.     

Site-directed mutagenesis study of the antibody 2D7 which catalyzes a reaction for insertion of Cu2+ into mesoporphyrin

Monoclonal antibody 2D7 generated against a transition-state analog N-methyl mesoporphyrin catalyzes a reaction for insertion of a cupric ion into mesoporphyrin. To investigate amino acid residues responsible for the catalytic activity, site-directed mutagenesis of the amino acid residues in the third complementarity determining region of the heavy chain (CDRH3) was performed on the antigen-binding fragment (Fab) of the antibody. Recombinant Fab mutants, in which Arg95 is replaced with Ala (R95A), Asp96 with Asn (D96N) and Met97 with Gly (M97G), were examined in terms of the catalytic efficiency of the reaction (k/K(S)) and the dissociation constant for N-methyl mesoporphyrin binding (K(d)) and these values were compared with those of the wild type. The k/K(S) values of the R95A and D96N mutants were 0.96% and 1.0% of that of the wild type, respectively, whereas the M97G mutant had no detectable catalytic activity. The K(d) values of the R95A and D96N mutants were 165 and 69 times that of the wild type, respectively, while that of the M97G mutant was similar to that of the wild type. The relationship between the k/K(S) and 1/K(d) values in the wild type and the R95A and D96N mutants suggests that Arg95 and Asp96 are responsible for stabilizing the transition-state in the catalytic reaction. The results of the M97G mutant allow us to propose that Met97 plays an important role in the catalytic activity probably due to a subtle and specific conformation of the antibody.     

A study of multivariate (\bar{X},S)control chart based on Kullback–Leibler information

Recently, Chou et al. [11] have considered the multivariate control chart for monitoring the process mean vector and covariance matrix for the related quality characteristics simultaneously by using log-likelihood ratio statistics. They have computed the approximation formula described with Bernoulli polynomials of degrees r≥30 by using software MATHEMATICA 4.0 for obtaining the control limit with sufficient accuracy for the specified type I error probability in the chart. However, they cannot have obtained the approximation formula for the power evaluation. By the way, Kanagawa et al. [12] have proposed the $(\bar{x},s)$ control chart for monitoring the mean and variance simultaneously based on Kullback–Leibler information when quality characteristics obey a univariate normal distribution. In this article, by adopting the procedure by Kanagawa et al., we propose the other approximation formula for determining simply the control limit with sufficient accuracy for the specified type I error probability. Furthermore, the power evaluation for the chart is also considered in theory.     

Interfacial Reaction Between Cu Substrates and Zn-Al Base High-Temperature Pb-Free Solders

Chemical reactions between Cu substrates and Zn-Al high-temperature solder alloys, Zn-4Al and Zn-4Al-1Cu (mass%), at temperatures ranging from 420°C to 530°C were experimentally investigated by a scanning electron microscope using backscattered electrons (SEM-BSE) and an electron probe microanalyzer (EPMA). Intermediate phases (IMPs), β(A2) or β′(B2), γ(D8₂), and ε(A3) phases formed and grew during the soldering and aging treatments. The consumption rate of the IMP for Cu substrates is described by the square root of t in both the alloys, while the additional Cu in the molten Zn-Al alloy slightly suppresses the consumption of Cu substrates. The growth of IMPs during soldering treatment is controlled by the volume diffusion of constituent elements, and its activation energy increases in the order of Q _ε < Q _γ < Q _β. In view of the aging process, the growth of IMPs is considered to be controlled by the volume diffusion. In particular, the layer thickness of γ rapidly grows over 200°C, although the thickness of the β layer grows very slowly.     

Variable stage-independent double sampling plan with screening for acceptance quality loss limit inspection scheme

The quality loss suggested by Taguchi has been recognised as a new quality evaluation based on variable property instead of the quality evaluation based on traditional attribute property such as the proportion of nonconforming items. Some variable sampling inspection plans in order to assure the quality have been considered. As one of those sampling inspection plans, the single sampling plan with screening (SSPS) has been constructed for acceptance quality loss limit inspection scheme. Further, the repetitive group sampling plan with screening (RGSPS) has been developed for reducing the average total inspection (ATI). Although ATI by RGSPS has successfully been reduced in comparison with ATI by SSPS, RGSPS may sometimes increase the average sampling frequency (ASF) in return for reducing ATI. In this study, the stage-independent double sampling plan with screening (SIDSPS) based on the concept of the acceptance quality loss limit inspection scheme is proposed under the consideration of the trade-off between ATI and ASF. Through some numerical comparisons about ATI and ASF in SSPS, RGSPS, and SIDSPS, the usefulness of SIDSPS proposed in this study is confirmed.     

Fracture behavior of poly(vinyl chloride)/methyl methacrylate/butadiene/styrene polymer blends

The fracture mode of poly(vinyl chloride)/methyl methacrylate/butadiene/styrene (PVC/MBS) polymer blends can change from ductile to brittle in accordance with the changes in shape of the test specimen or test conditions. Therefore, the mechanisms of impact energy absorption and the main cause of stress whitening are complicated. The following results on PVC/MBS blends were obtained by carrying out fracture experiments at different test speeds and temperatures:

• (1) The ductile/brittle fracture mode of the PVC and PVC/MBS blends can be explained by σ (the craze initiation stress)/σ_y (the shear yield initiation stress), which depends on the strain rates and temperature.
• (2) The fracture behavior of the PVC/MBS blends can be classified into the following types from the standpoints of fracture mode and whitening degree: Fracture I: ductile fracture without whitening; Fracture II: ductile fracture with whitening; and Fracture III: brittle fracture without whitening.
• (3) The following concepts can be estimated from the measurements of yield stress, specific gravity and SEM, TEM and visual observations. In Fracture I, shear yield occurs mainly. In Fracture II, both shear yield and crazing occur. In Fracture III, deformation of the rubber and local crazing occur.
• (4) The main cause of stress whitening in PVC/MBS blends is light scattering by cavities in the rubber particles.
• (5) In Fracture II, at first, crazes with cavities in the rubber particles occur. Then, shear yield occurs. Finally, crazes are healed by the heat, and only the cavities in the rubber remain.