Frequency Tunable Microstrip Patch Antenna Using RF MEMS Technology

A novel reconfigurable microstrip patch antenna is presented that is monolithically integrated with RF microelectromechanical systems (MEMS) capacitors for tuning the resonant frequency. Reconfigurability of the operating frequency of the microstrip patch antenna is achieved by loading it with a coplanar waveguide (CPW) stub on which variable MEMS capacitors are placed periodically. MEMS capacitors are implemented with surface micromachining technology, where a 1-mum thick aluminum structural layer is placed on a glass substrate with a capacitive gap of 1.5 mum. MEMS capacitors are electrostatically actuated with a low tuning voltage in the range of 0-11.9 V. The antenna resonant frequency can continuously be shifted from 16.05 GHz down to 15.75 GHz as the actuation voltage is increased from 0 to 11.9 V. These measurement results are in good agreement with the simulation results obtained with Ansoft HFSS. The radiation pattern is not affected from the bias voltage. This is the first monolithic frequency tunable microstrip patch antenna where a CPW stub loaded with MEMS capacitors is used as a variable load operating at low dc voltages     

Integration of 0/1-Level Packaged RF-MEMS Devices on MCM-D at Millimeter-Wave Frequencies

This paper reports on the development and optimization of 0/1-level packaged coplanar waveguide (CPW) lines and radio-frequency microelectromechanical systems (RF-MEMS) switches up to millimeter-wave frequencies. The 0-level package consists of an on-chip cavity obtained by flip-chip mounting a capping chip over the RF-MEMS device using BenzoCyclobutene (BCB) as the bonding and sealing material. The 0-level coplanar RF feedthroughs are implemented using BCB as the dielectric; gold stud-bumps and thermocompression are used for realizing the 1-level package. The 0-level packaged switches have been flip-chip mounted on a multilayer thin-film interconnect substrate using a high-resistivity Si carrier with embedded passives and substrate cavities. The insertion loss of a single 0/1-level transition is below -0.15 dB at 50 GHz. The measured return loss of a 0/1-level packaged 50-Omega CPW line remains better than -19 dB up to 71 GHz and better than -15 dB up to 90 GHz. It is shown that the leak rate of BCB sealed cavities depends on the BCB width, and leak rates as low as 10^-11 mbar.l/s are measured for large BCB widths (> 800 mum), dropping to 10^-8 mbar.l/s for BCB widths of around 100 mum. Depending on the bonding conditions, shear strengths as high as 150 MPa are achieved.     

Utilization of Anisotropic Metamaterial Layers in Waveguide Miniaturization and Transitions

We introduce a new approach which enables a waveguide to support propagation of electromagnetic waves below the cutoff frequency, as well as which avoids undesirable reflections in a waveguide. These are achieved through the usage of an anisotropic metamaterial layer by employing the concept of coordinate transformation. The proposed method can be utilized for the fabrication of miniaturized waveguides, and for the elimination of discontinuities in abrupt waveguide transitions. We demonstrate some numerical experiments for finite element simulations of parallel-plate and dielectric slab waveguides.     

Rapidly tunable optical add-drop multiplexer utilising relaxed beam splitters

A polarisation-independent four-port electro-optic tunable filter in the 1530 nm wavelength regime utilising non-polarising relaxed beam splitters and strain-induced polarisation converters on LiNbO₃ with 16 nm tuning range and 46 ns tuning speed is reported.     

The microstructure of Cu films deposited by the self-ion assisted technique

The microstructures of Cu films deposited by the self-ion assisted, partially ionized beam (PIB) deposition technique under two different accelerating potentials, 0 KeV and 6 KeV, are compared. The 6 KeV film shows a bimodal (111) fiber and (100) fiber texture with an abundance of twin boundaries and a relatively large average grain size with a typical lognormal distribution. The 0 KeV film consists of small, mostly (111) oriented grains with islands of abnormally large (100) grains. The controlling factors for the abnormal growth of the (100) grains are discussed in relation to the observed microstructures, showing that all factors necessary for abnormal (100) growth are present in the films.     

A Symbolic Pole/Zero Extraction Methodology Based on Analysis of Circuit Time-Constants

This paper introduces a methodology for symbolic pole/zero extraction based on the formulation of the time-constant matrix of the circuits. This methodology incorporates approximation techniques specifically devoted to achieve an optimum trade-off between accuracy and complexity of the symbolic root expressions. The capability to efficiently handle even large circuits will be demonstrated through several practical circuits.     

Stimulation of negative magnetoresistance by an electric field and light in silicon doped with boron and manganese

It is experimentally ascertained that light stimulates the negative magnetoresistance observed in a high electric field in silicon doped with boron and manganese. The optimum conditions (the electric field, temperature, illumination, and resistivity of the material) for observation of the largest magnitude of negative magnetoresistance in (Si:B):Mn are determined. The dependence of the negative magnetoresistance on the concentration of compensating impurity is established.     

The tail of localized states in the band gap of the quantum well in the In0.2Ga0.8N/GaN system and its effect on the laser-excited photoluminescence spectrum

Semiconductors - It is established experimentally that the peak in the photoluminescence spectrum of the In0.2Ga0.8N/GaN heterostructure with a quantum well shifts by ～150 meV as the power...     

Fabrication of Strain-Relaxed Si<Subscript>1 − <Emphasis Type="Italic">x</Emphasis></Subscript>Ge<Subscript>x</Subscript>/Si(001) Buffer Layers of Low Surface Roughness

The results are presented of the fabrication of strain-relaxed graded Si_{1 − x} Ge_x/Si(001) buffer layers with a maximum Ge fraction of about 0.25 that have a low density of threading dislocations (<10⁶ cm⁻²) and low surface roughness. The buffer layers are grown by atmospheric-pressure hydride CVD. It is found that chemical mechanical polishing can reduce their surface roughness to a level comparable with that of the original Si(001) substrates. It is shown that the polished buffer layers can serve as substrates for MBE-grown SiGe/Si heterostructures.__________Translated from Mikroelektronika, Vol. 34, No. 4, 2005, pp. 243–250.Original Russian Text Copyright © 2005 by Vostokov, Drozdov, Krasil’nik, Kuznetsov, Novikov, Perevoshchikov, Shaleev.     

Locating the nodes: cooperative localization in wireless sensor networks

Accurate and low-cost sensor localization is a critical requirement for the deployment of wireless sensor networks in a wide variety of applications. In cooperative localization, sensors work together in a peer-to-peer manner to make measurements and then forms a map of the network. Various application requirements influence the design of sensor localization systems. In this article, the authors describe the measurement-based statistical models useful to describe time-of-arrival (TOA), angle-of-arrival (AOA), and received-signal-strength (RSS) measurements in wireless sensor networks. Wideband and ultra-wideband (UWB) measurements, and RF and acoustic media are also discussed. Using the models, the authors have shown the calculation of a Cramer-Rao bound (CRB) on the location estimation precision possible for a given set of measurements. The article briefly surveys a large and growing body of sensor localization algorithms. This article is intended to emphasize the basic statistical signal processing background necessary to understand the state-of-the-art and to make progress in the new and largely open areas of sensor network localization research.