Thermophysical properties of (U,Y)O2

We prepared polycrystalline pellets of (U,Y)O₂, containing YO_1.5 up to 11 mol.%. We performed indentation tests on the pellets, and evaluated the Young’s modulus and hardness. We measured the heat capacity and the thermal diffusivity, and evaluated the thermal conductivity. We succeeded in evaluating the effect of Y content on the thermophysical properties of (U,Y)O₂. We revealed that the Young’s modulus, hardness, and thermal conductivity of (U,Y)O₂ decreased with increasing the Y content.     

Cryptosporidium monitoring system at a water treatment plant, based on waterborne risk assessment.

The water volume required for daily monitoring of Cryptosporidium (which can statistically ensure an annual risk of infection below 10(-4)), was assessed by evaluating the applicability of the Poisson lognormal (PLN) distribution in microbial risk assessment. PLN showed as good a fit to the observed data as to the negative binomial distribution. From the estimated PLN distributions for the source and finished water, the efficacy of the oocyst removal by the conventional water treatment process was estimated to follow log-normal distribution (median = 3.16 log10, 95% CI = 4.27-2.05 log10). The 365 consecutive negative results of daily monitoring for 180 L of finished water were found to be statistically equivalent to the annual risk of infection below 10(-4). This research also suggested the possibility of applying a qualitative detection method, such as CC-PCR, as a routine monitoring method for the quantitative risk management.     

Iterative Design of the Reduced-Order Weight and Controller for the $H_{infty}$ Loop-Shaping Method Under Open-Loop Magnitude Constraints for SISO Systems

The H _infin loop-shaping method is known to be an effective control method. However, it has two drawbacks. The first is that it is difficult to select appropriate loop-shaping weights, and the second is that the resulting controller is very complex. For the first drawback, Lanzon has proposed a suboptimal loop-shaping weight design method. It is formulated as a generalized eigenvalue minimization problem (GEVP). This suboptimal loop-shaping weight design method provides high-order weights, exacerbating the second drawback. To resolve these two drawbacks, a reduced-order loop-shaping weight design method is proposed for SISO systems in this paper. In the proposed method, the weight structure is first fixed, and the weight is then decomposed into a frequency-dependent vector and parameter matrices characterizing the loop-shaping weight. Since the open-loop constraints are represented as linear matrix inequalities with respect to the parameter matrices, the proposed reduced-order loop-shaping weight design problem for SISO systems is formulated as a GEVP, as well as Lanzon's suboptimal loop-shaping weight design method. The proposed method can reduce the designer's burden, although it is only valid for SISO systems. The effectiveness of the proposed method is verified experimentally by velocity control of a belt-driven two-mass system.     

Aluminium alloy welding by CO2 laser using filler wire ‐AIN formation and aluminium alloy weldability

Based on literature sources and the author's own research, this article presents the current state of knowledge about composite coatings created by means of the plasma transfer method. The general characteristics of composite coatings and their strengthening mechanisms have been described. Methods of creating composite coatings by means of the plasma transfer method have also been discussed.     

Design and manufacturing of JT-60SA vacuum vessel

JT-60 is planned to be upgraded to JT-60SA tokamak machine with fully superconducting coils, which is a project of the JA-EU satellite tokamak program under both Broader Approach program and Japanese domestic program. The JT-60SA vacuum vessel (VV) has a D-shape poloidal cross section and a toroidal configuration with 10° facet segmented in toroidal direction. The material of the VV is 316L stainless steel with low cobalt content of <0.05 wt%. A double wall structure is adopted for the VV to ensure high rigidity and high toroidal one-turn resistance simultaneously.Fundamental welding R&D and a trial manufacturing of the 20° upper half of the VV have been performed to study the manufacturing procedure. After the confirmation of the quality of the mock-up, manufacturing of the actual VV started in November 2009.     

HR-TEM observation of laser pressure weld of galvannealed steel and pure aluminium

Laser pressure welding was conducted by changing the laser power and the roller pressure in the previous experiment. It was revealed that dissimilar metal welding of galvannealed steel and pure aluminium was feasible in a wide range of welding conditions. When the roller pressure was more than 1.96 kN at the laser powers equal to or less than 1400 W, the joint strengths were so high that the specimens in the tensile shear and the peel tests fractured in the A1050 parent metal.

In order to know the reason for such high strengths of joints with thick compound layers and the joining mechanism, the compound layer was observed by HR-transmission electron microscopy (TEM). The TEM observation results revealed that the main phase in the compound layer was the solid solution of Al + Zn. Moreover, the intermetallic compound was identified as FeAl, Fe₂Al₅, Fe₄Al₁₃ and Fe₂Al₅Zn_0.4 phase by electron diffraction. The Fe₃Zn₁₀ (Γ phase) of Fe–Zn intermetallic compound was confirmed on a Fe base material. It is guessed that the joining areas were heated at a range of 782°C more than 665°C, a melting point of Al, by laser irradiation because the δ_lk phase aspect was not confirmed. Because the surfaces of A1050 and Zn plated layer were melted thinly, the layer was over 10 μm thicker. The reason for the production of high-strength joints with a relatively thick intermetallic compound layer was attributed to the formation of (Al + Zn) phase with finely dispersed intermetallic compounds.     

Laser pressure welding of aluminium and galvannealed steel

Dissimilar metal joints of galvannealed steel and commercially available pure aluminium (A1050) sheets were produced by changing the laser power and the roller pressure by the laser pressure welding method. In this method, the YAG laser beam was irradiated into a flare groove made by these dissimilar metal sheets. In addition, the laser beam was scanned at various frequencies and patterns through the fθ lens using two-dimensional scanning mirrors. Then the sheets were pressed by the pressure rolls to be joined. The compound layers in the weld interface were observed by optical microscope, and the layer thicknesses were measured. The thicknesses were in the range of 7–20 μm. The mechanical properties of welded joints were evaluated by the tensile shear test and the peel test. In the tensile shear test, the strengths of the joints produced under the most welding conditions were so high that the fracture occurred through the base aluminium sheet. In the peel test of the specimens subjected to the laser beam of 1200–1400 W power under the roller pressure of 2.94 kN, the specimen fracture took place in the base aluminium sheet. Even if the compound layer was thick, high joint strength was obtained. In order to know the reason for such high strength of joints with thick compound layers and the joining mechanism, the compound layer was observed by the HR-TEM. The TEM observation results revealed that the main phase in the compound layer was the solid solution of Al + Zn. Moreover, the intermetallic compound was identified as FeAl, Fe₂Al₅, Fe₄Al₁₃, and Fe₂Al₅Zn_0.4 phase by electron diffraction. The Fe₃Zn₁₀ (Γ phase) of Fe–Zn intermetallic compound was confirmed on a Fe base material. It is assumed that the joining areas were heated in a range of 782°C more than 665°C, a melting point of Al, by laser irradiation because the δ_lk phase aspect was not confirmed. Because the surfaces of A1050 and Zn plated layer were melted thinly, the layer was over 10 μm thicker. The reason for the production of high strength joints with the relatively thick intermetallic compound layer was attributed to the formation of (Al + Zn) phase with finely dispersed intermetallic compounds.     

Quantitative evaluation of perceived whiteness based on a color vision model

This article describes a new perceived whiteness index, C/V index, which focuses on the brightness‐enhancement effect of color components included in the spectral reflectance factor distribution of approximate white objects or in the spectral power distribution of illuminations. The index is developed on the basis of a color vision model. The perceived whiteness of 18 approximate white samples was evaluated, and then a predictability of the index was compared with 17 types of existing whiteness indices. As a result, the C/V index was one of the indices indicating the best predicting performance. The aforementioned findings show that the C/V index is effective in evaluating the perceived whiteness of approximate white objects and the brightness‐enhancement effect of color components is an important factor in determining the perceived whiteness. © 2009 Wiley Periodicals, Inc. Col Res Appl, 2010