ENHANCEMENT OF DRYING RATES FOR SLAB-LIKE MATERIALS IN A FLUIDIZED DESICCANT DRYING MEDIUM

The kinetics of drying of slab-like materials in- mersed in a fluidized bed of silica gel particles at a relatively low temperature, 30 °C, is studied. As a re- sult of desiccant particle action large surface-to-bed moisture fluxes and, consequently, large drying rates are attained. For all examined materials (cardboard, veneer, asbestos and ceramic plates) the drying times in the desiccant fluidized bed are much shorter than those in the empty apparatus with the same air flow, temperature and humidity. A simple, diffusional model of the drying based upon a mean mass capacity concept is developed. The drying curves calculated from the model are in good agreement with the experimental ones.     

Further studies on polyamides from bisacid a2

Earlier work on the low temperature solution polyamidation of bisacid A2 has raised a number of structural problems. Work carried out more recently showed that the problem of apparent nonisostoichiometry could be reasonably satisfactorily explained. The present paper reports the synthesis and investigates the properties of a further series of polyamides based upon Bisacid A2. More importantly, however, a detailed characterization and evaluation of the new polymers with respect to their structures is presented. This enabled us to compare the various structures in the light of the experimental evidence provided by a number of analytical and spectroscopic techniques, solution behavior, molecular weight, and thermal, morphological, and mechanical properties. Some work was also done on the effect of incorporating a small amount of a trifunctional monomer into the polyamide system.     

Fatty acid composition of phospholipids and neutral lipids during embryonic and early larval development in Atlantic herring (Clupea harengus,L.)

The fatty acid compositions of total polar and total neutral lipids of Atlantic herring eggs and larvae were determined immediately before fertilization, after fertilization and at various times during subsequent embryonic and early larval development. Within 3 hr after fertilization the percentage of total PUFA in neutral lipid decreased from 33% to 20%, with a reciprocal increase in monoenes. Thereafter the percentage of PUFA in the neutral lipids increased progressively, attaining the original level in ripe eggs by the time of yolk sac absorption. During the larval stages the percentage of PUFA continued to increase in the neutral lipid, reaching almost 44% of the total by day 32 after fertilization, although it was reduced to 32% by day 36. The percentage of monoenes in the neutral lipid displayed a progressive decrease during the whole period of development from 3 hr after fertilization. Throughout all the developmental periods the fatty acid composition of total polar lipids remained essentially constant. The polar lipids of the yolk sac displayed virtually the same fatty acid composition as the larval bodies, but the neutral lipids of the yolk sac were low in PUFA compared to the larval bodies. The results are discussed with reference to changes in lipid class composition during development. The conservation of high levels of PUFA in lipids during embryogenesis and early larval development reflects the importance of these fatty acids during development.     

Upgrading coal-derived liquids to diesel fuel

Distilled fractions of a coal-derived liquid from the H-Coal process were upgraded to diesel fuel by catalytic hydrotreatment. The total hydrotreated products were distilled into naphtha (<180°C) and diesel fuel fractions (>180°C) and the diesel fractions were analysed for hydrocarbon-type composition, hydrogen content and some diesel fuel properties. GC—MS-analyses were carried out on the hydrocarbon-type fractions to identify individual chemical compounds. To investigate the effect of different distillation cut points on diesel fuel yield and properties, cut points for one hydrotreated product were varied. The diesel fuel cetane numbers were correlated with percentage hydrogen, total aromatics and saturates. Cetane numbers above 40 were obtained for diesel fuels containing (i) more than 75% saturates, (ii) less than 15% total aromatics and (iii) a hydrogen content above 12.8%. Compounds identified by GC—MS-analyses (in the diesel fractions) were typical aromatic and cycloparaffin compounds. Normal-and iso-paraffin compounds were not detected. By varying the distillation cut point from 135 to 180°C, the cetane number of the residual diesel fraction improved from 37 to 44. This increase is ascribed to the removal of aromatic compounds in the 135–180°C boiling point range.     

Radiation safety of a population inhabiting the area where a nuclear facility is situated

Translated from Atomnaya Énergiya, Vol. 67, No. 2, pp. 81–83, August, 1989.     

The heater test at the Grimsel Rock Laboratory: The thermo-mechanical response of the rock mass to a heat flux

The Grimsel Test Site (Felslabor Grimsel — FLG) is situated at a depth of 450 m in the Juchlistock massif of the Bernese Oberland. It is managed by the National Cooperative for the Storage of Radioactive Waste (NAGRA-Switzerland).By means of a heater test, the power output of canisters filled with high-level waste is simulated. This heater test is performed by the German Gesellschaft für Strahlen- und Umweltforschung — GSF. Two electrical heaters, with a heatable length of 6 m, a diameter of 0.3 m and an available power of 4 kW/m, are installed in two vertical boreholes. One of them is located in the granite adjacent to a strongly fractured lamprophyre vein, the other one directly within this disturbed zone. They are operating since August 1986.The thermo-mechanical reaction of the rock mass is registered by a large number of measurement devices which are installed in an array of instrument boreholes around the heaters. They record the deformation and the alteration of rock stresses, the pore water pressure and the water conductivity caused by heating.     

ALUM SHALE BITUMEN MATURATION AND MIGRATION: IMPLICATIONS FOR GOTLAND'S OIL

Thermal maturation of Swedish Alum Shale kerogen and bitumen has been determined from core samples from Eastern and Central Sweden. In samples from Eastern Sweden (Öland and Gotland), the kerogen and bitumen are thermally immature with respect to petroleum generation. In some areas of Central Sweden (Närke, ÖstergÖtland, and Kinnekulle in VästergÖtland), the kerogen is immature, whereas the bitumen is marginally mature to mature. In other areas of Central Sweden (Halleberg-Hunneberg in VästergÖtland), the kerogen is supermature and the bitumen mature. This suggests that bitumen from a mature source-rock has migrated into the Alum Shales of Central Sweden. Migration in Central Sweden is further evidenced by the occurrence of obviously-migrated bituments in vugs and voids in the organicpoor Ordovician limestone overlying the Alum Shale in Central Sweden, and in concretions within the Alum Shale itself. Based on biomarker distributions of extracted bitumen, Alum Shale kerogen pyrolysate and obviously-migrated oils, and the fact that the Alum Shale in most of the areas studied is the only petroleum source-rock extant, it is suggested that the migrated bitumen in Central Sweden is from the Alum Shale itself. Bitumen has migrated from areas where the Alum Shale is in close proxmity to Permo-Carboniferous intrusions, such as Halleberg-Hunneberg, into nearby areas such as Närke and ÖstergÖtland, where there is no evidence of intrusion and the indigenous organic matter is thermally immature. Other areas, where Alum Shales were associated with intrusions and consequently sourced oil, may have been eroded away. There are producing wells on the island of Gotland, where the Alum Shale is also thermally immature. It is therefore assumed that heating which was responsible for generating Gotland's oil was very localized (such as by an intrusion) or that the oil has migrated from a thermally moremature, distant area. On the basis of reservoir rock porosity, and the fact that the Alum Shale of Gotland contains no migrated component, localized heating is favored.