Design Water Levels in Tidal River Systems under the Influence of Typhoons

Water levels in tidal rivers are subject to the influence of both fluvial and tidal factors. The interaction between these factors is rendered more complex in regions affected by typhoons, which typically result in the combined occurrence of heavy rainfall and high sea levels.
Previous studies have outlined an analytical approach for calculating design water levels based on dividing the fluvial and tidal series into a typhoon and a non-typhoon component. This paper illustrates the steps involved in the analytical approach and describes its application to drainage basins in Hong Kong.
The approach provides a practical means for calculating design water levels, and is recommended for final design purposes. The results of using the full analysis may be approximated by using a sub-set of analytical results, and should prove satisfactory for the purposes of outline design.     

Geomechanical model simulation for the varied rock formations of the Kadana dam foundation,Gujarat, India

Bulletin of Engineering Geology and the Environment - Precambrian layered rocks consisting of quartzites, phyllites and metagreywackes of the Aravallis having a large variation in thickness,...     

Oxygen transfer in a rotating disc treatment plant

In this paper experiments are described in a bio-disc pilot plant. A new method has been developed for a reproducible measurement of the thickness of the waterfilm on the rotating discs. The results were used to calculate the oxygen transfer coefficient into water (K_L). The values of K_L, calculated in this way, appeared to be considerably higher than experimental K_L-values, which is mainly due to the fact that the water layer on the rotating disc is outdistanced by the disc. This effect has not been taken into account in the literature so far.     

Sorption of benzenesulfonates by weak base anion exchange resins

Weak base phenol formaldehyde anion exchange resins were found to have an excellent capacity for removing the anionic organic species benzenesulfonate (BS), p-toluenesulfonate (PTS) and dodecylbenzenesulfonate (DBS) from pH 2 and 4 solutions. The capacity for DBS was generally greater than that of activated carbon and significantly greater than that of a polystyrene-divinylbenzene resin with no ion exchange functional groups. The maximum capacity of the weak base resins appeared to be limited by the exchange capacity of the resin. The mechanism of removal was strongly indicated as being either ion exchange at the amine functional groups in the acid form, or uptake of a proton by the amine groups in the free base form with the organic anion as the associated counter ion. Increasing concentrations of Cl⁻ decreased the amount of organic anion that could be sorbed.The swelling of one of the resins, Duolite A-7, also had a marked effect on its sorption capacity. The pores of the acid chloride or acid organic anion form of the resin were apparently larger than those of the free base form; thus, as conversion of the resin to the acid form took place, a greater amount of uptake was observed. The effect of swelling on the capacity of Duolite S-37 was much less, apparently owing to its larger pore structure, but its capacity for DBS at low pH was lower than that for A-7 because of its lower nitrogen content. Also, BS and DBS were easily removed from the weak base resins by washing them with NaOH. Four bed volumes of 1 m NaOH gave essentially complete regeneration of BS saturated A-7.     

Treatment capability of a physical—Chemical package plant

A short-term study of a commercially-available physical—chemical waste treatment plant is reported. Results indicate that an excellent quality of effluent can be consistently obtained despite wide fluctuations of influent wastewater characteristics. Physical, chemical, and biological parameters were monitored. The short-term data obtained offer some evidence of superior treatment efficiency in terms of COD, color, turbidity, and phosphorus removals when compared to more conventional treatment methods.     

西安市金华北路邮政局营业楼裂缝分析

本文用弦线模量计算了营业楼地基的压缩变形和湿陷变形,以及由它们引起的差异沉降值和局部倾斜。计算结果和楼房的裂缝情况吻合。计算湿陷变形时考虑地基浸水后的含水量为30.00％,这是由实测情况确定。根据浸水的实际状况计算建筑物的湿陷变形,分析工程事故在文献中似未见到。     

Classic and novel brominated flame retardants (BFRs) in common sole (Solea solea L.) from main nursery zones along the French coasts

Brominated flame retardants (BFRs) were investigated in juvenile common sole from nursery zones situated along the French coast in 2007, 2008 and 2009. Extensive identification was performed with regard to PBDEs, novel BFRs 1,2-bis(2,4,6-tribromophenoxy)ethane (BTBPE) and decabromodiphenylethane (DBDPE), and other non-PBDE BFRs, namely, hexabromobenzene (HBB) and 2,2′,4,4′,5,5′-hexabromobiphenyl (BB-153). Polybrominated diphenyl ether (PBDE) concentrations (Σ 14 congeners) ranged from 0.01 ng/g to 0.16 ng/g wet weight (ww) in muscle, and 0.07 ng/g to 2.8 ng/g ww in liver. Concentrations were in the lower range of those reported in the literature in other European locations. Lower PBDE concentrations, condition indices and lipid contents were observed in the Seine estuary in 2009, possibly in relation to a lower water flow. The PBDE patterns and ratios we observed suggested that juvenile sole have a relative high metabolic degradation capacity. Non-PBDE BFRs were detected at lower levels than PBDEs, i.e., within the < method detection limit - 0.005 ng/g ww range in muscle, and < method detection limit - 0.2 ng/g ww range in liver. The data obtained is of particular interest for the future monitoring of these compounds in the environment.     

Coagulation dynamics of fractal flocs induced by enmeshment and electrostatic patch mechanisms

The size and structure of flocs during floc formation were monitored for various coagulation mechanisms. Two distinctive mechanisms, namely, enmeshment and electrostatic patch, govern the dynamics of kaolin particles coagulation by polyaluminum chloride (PACl). They were investigated by small angle static light scattering (SASLS) and solid-state ²⁷Al NMR. In addition, a novel wet SEM (WSEM) was used in-situ to image the morphology of the aggregate in aqueous solution. Synthetic suspended particles were coagulated by two PACl products, a commercial product (PACl) and one laboratory product (PACl-E). The PACl-E contained more than 60% Al₁₃ while the PACl contained only 7% Al₁₃, with large percentage of colloidal Al. For coagulation by PACl at neutral pH and high dosage where the strong repulsion between particles occurs, the enmeshment ruled by reaction-limited aggregation (RLA) results in larger sweep flocs as well as higher fractal dimensional structure. For coagulation by PACl-E at alkaline pH and low dosage, the flocs were coagulated predominately by electrostatic patch with Al₁₃ aggregates. At such condition, it is likely that diffusion-limited aggregation (DLA) predominately rule PACl-E coagulation. The fractal dimension (D_s) values of PACl and PACl-E flocs formed at enmeshment and electrostatic patch increased with dosage, respectively. When breakage of flocs occurs, the breakage rate of PACl-E flocs is slower than that of sweep flocs. By WSEM imaging, the adsorption of spherical Al precipitates onto the particles was observed to form sweep flocs with a rough and ragged contour, while the PACl-E flocs were formed with a smooth and glossy structure.