Formation of C4 species in the deactivation of a Pd/SiO2 catalyst during the selective hydrogenation of acetylene

The deactivation characteristics of Pd/SiO₂ in the selective hydrogenation of acetylene were correlated with changes in the amount of the C4 species produced. The amounts of butenes produced changed in parallel with the catalyst activity, indicating that the rate limiting step for butene production was the same as that for acetylene hydrogenation. On the other hand, the amount of 1,3-butadiene produced changed, showing a maximum with catalyst deactivation because 1,3-butadiene is an intermediate in the sequential reaction process which involves both the production and consumption of 1,3-butadiene. This was verified by a simultaneous TG/reaction experiment showing that 1,3-butadiene was a precursor of green oil. The catalyst showed a self-regenerative behavior in its activity and the amounts of C4 species produced during the early stage of deactivation because two opposite factors, which contributed to either the lowering or the promotion of activity, were involved in the process. A specific type of polymer species, produced during the initial period of deactivation, is proposed to be responsible for the promotion of catalyst activity.     

Compact Dipole Antenna for Terrestrial Digital Multimedia Broadcasting Service

A compact dipole antenna for the terrestrial digital multimedia broadcasting (TDMB) application is presented. The length of the antenna is about 0.06λ at the TDMB resonance frequency of 190 MHz. Miniaturization of the antenna is achieved by using meander structures and lumped elements. The proposed antenna has two resonance frequencies and covers the TDMB band from 174 MHz to 216 MHz in Korea. The antenna has good impedance bandwidth and radiation characteristics for the TDMB. The experimental results of the designed dipole antenna are presented and analyzed.     

BioFET sensor for detection of albumin in urine

Characterisation of a BioFET for detection of albumin in a mixture of human urine is presented. To avoid electrolyte effect of the urine, it was measured in PBS (phosphate buffer saline) at a fixed pH after albumin binding. The drain current was modulated by the albumin bound to the anti-albumin immobilised on the gate surface of the BioFET. The current variation ratio was likely to be proportional to the concentration of the albumin in the range 50-250 mg/1. The results show the feasibility of the BioFET as a urinary albumin sensor.     

Austenitizing treatment influence on the electrochemical corrosion behavior of 0.3C-14Cr-3Mo martensitic stainless steel

Effects of austenitizing treatment temperatures on aqueous corrosion properties of martensitic stainless steels were investigated by electrochemical tests (potentiodynamic test, potentiostatic test and electrochemical impedance spectroscopy), and surface analyses (optical microscopy and XRD). The results of potentiodynamic test revealed that the breakdown potential increased with the increased austenitizing temperature, indicating increased relative resistance to initiation of localized corrosion. EIS measurements showed that MSS3 (1030 °C) exhibits larger polarization resistance value than MSS1 (970 °C) and MSS2 (1000 °C) at passive and breakdown states. This was caused by decreasing the amount of Cr-rich M₂₃C₆ carbide which acts as preferential sites for pitting corrosion.     

Dynamics modeling and analysis of a biped walking robot actuated by a closed-chain mechanism

We developed a new type of human-sized biped walking robot (BWR) driven by the closed-chain type of joint actuator. Each leg of the robot is composed of three pitch joints and one roll joint. In all, a 15 degree-of-freedom robot including four arm joints and three joints for the head was developed. The BWR was developed to walk autonomously such that all leg joints are actuated by small 90 W dc motors/drivers and dc batteries and controllers which are boarded. The joint actuator for the BWR is composed of the four-bar-link mechanism driven by the ball screw which has high strength and high gear ratio. A dynamics modeling of the developed BWR for forward walking is presented in which the revolute joint dynamics are transformed into the prismatic joint dynamics of the ball screw. Also, an analysis on the four-bar-link mechanism applied to the joint actuator and on the structure of the BWR is shown. The design specification of the actuating motor for the BWR is analyzed through the torque analysis of the four-bar-link actuator. Through walking experiments of the BWR, the walking performance and trajectory tracking ability is shown. © 2004 Wiley Periodicals, Inc.     

A self-resonant frequency-modulated micromachined passive pressure transensor

In this paper, we report on the design, fabrication, and test of a passive pressure transensor. The sensor uses the self-resonant frequency modulation of an integrated coil to detect the pressure variations. This modulation is generated by the relative displacement of a ferrite core attached to a silicone rubber membrane. This scheme simplifies the packaging of the passive transensor by removing the requirement for a separate capacitor to form the resonator. A 30-turn 1.7-/spl mu/H coil having dimensions of 3/spl times/3 mm/sup 2/ is used in a prototype design yielding a sensitivity of 9.6 kHz/kPa with a cylindrical ferrite core of 0.95-mm diameter and 0.5-mm height. We also present a theoretical model of the sensor that shows good agreement with the experimental data. This model can be a useful tool for further optimization of the senors.     

Data retention characteristics of sub-100 nm NAND flash memory cells

In contrast to the conventional theories, we have revealed that the most distinguished mechanism in the data retention phenomenon after Fowler-Nordheim (FN) stress in sub-100 nm NAND Flash memory cells is the annihilation of interface states. Interface state generation rate increases rapidly as the channel width of NAND flash cell decreases. Comparison of interface states and stress-induced leakage current (SILC) component during retention mode shows that the annihilation of interface states strongly affects data retention characteristics of the programmed cells.     

Adaptive contour smoothing based on inter-region contrast

An adaptive contour smoothing algorithm designed as a preprocessor for shape coders is presented. In the method, the degree of the adaptive smoothing is controlled based on the significance of each contour point, which is quantified according to inter-region contrast in an intensity image. The actual smoothing consists of an expansion operator and a thinning algorithm.