美国包装考察报告--中国包装总公司美国包装考察团考察记实

一、概述 笔者于2002年11月份随中国包装总公司组织的赴美包装考察团对美国包装业进行考察.本次考察重点参加了在美国芝加哥举行的国际包装机械展览会.它集中展示了美国、加拿大及欧洲发达国家的最新包装技术和整体实力.     

Hf-doped and NH/sub 3/-nitrided high-K gate dielectric thin film with least drain current degradation and flatband voltage shift

A novel technique to form high-K dielectric of HfSiON by doping base oxide with Hf and nitridation with NH/sub 3/, sequentially, is proposed. The HfSiON gate dielectric demonstrates excellent device performances such as only 10% degradation of saturation drain current and almost 45 times of magnitude reduction in gate leakage compared with conventional SiO/sub 2/ gate at the approximately same equivalent oxide thickness. Additionally, negligible flatband voltage shift is achieved with this technique. Time-dependent dielectric breakdown tests indicate that the lifetime of HfSiON is longer than 10 years at V/sub dd/=2 V.     

Ripple: a wireless token-passing protocol for multi-hop wireless mesh networks

This work presents a wireless token-passing protocol, named Ripple, for wireless mesh networks (WMNs). In contrast to existing random-access approaches, Ripple uses a decentralized controlled-access approach to protect nodes from unintentional packet collisions and maximize the spatial reuse. The performance of Ripple under an error-free wireless channel was investigated and the accuracy of the analysis was verified by simulation. Simulation results also indicated that Ripple achieved throughput, stability, and QoS enhancement than that of 802.11 DCF under a highly loaded situation.     

有线网络行业垄断性的改变及竞争形势分析

有线网络行业既具有自然垄断性,又具有行政垄断性.但随技术进步和国家政策的调整,其自然垄断性被削弱,行政垄断也被打破.在位的有线网络企业面临着两个层面的竞争：一是基于不同视频传输方式的竞争,二是同为有线网络传输方式的竞争,而后者是直接的竞争.对有线网络行业的竞争进行了SWOT分析.最后讨论了竞争形势下在位的有线网络运营商的应对思路.     

Enhancing both network and user performance for networks supporting best effort traffic

With a view on improving user-perceived performance on networks supporting best effort flows, e.g., multimedia/data file transfers, we propose a family of bandwidth allocation criteria that depends on the residual work of on-going transfers. Analysis and simulations show that allocating bandwidth in this fashion can significantly improve the user-perceived delay, bit transmission delay, and throughput over traditional approaches, e.g., by 58% on an 80% loaded linear network. A simple implementation based on TCP Reno, exemplifies how one might approach practically realizing such gains. We discuss several other advantages of incorporating such differentiation at the transport level. In particular we make the case that favoring small transfers combined with user impatience or peak rate constraints, both of which are natural mechanisms for users to express the utility of completing transfers, offers a lightweight approach to achieving good overall network goodput and/or utility for best effort networks.     

石膏转化制硫酸钾结晶动力学及结晶添加剂研究

研究了浓氨介质中石膏与氯化钾直接转化制硫酸钾的结晶动力学及结晶添加剂的作用效果。结果表明 ,硫酸钾在氨介质中的成核速率与晶体生长速率、悬浮密度、搅拌速率存在如下关联式 :B0 =5 .64 13×10 8G3.32 0 8Mt0 .0 559np0 .2 92 8。加入异丙醇、OP乳化剂及十二烷基苯磺酸钠等添加剂 ,可使硫酸钾结晶产品纯度提高 ,晶体形态整齐均匀     

Measurement and numerical simulation of three‐dimensional fiber orientation states in injection‐molded short‐fiber‐reinforced plastics

To determine three‐dimensional fiber orientation states in injection‐molded short‐fiber composites, a confocal laser scanning microscope (CLSM) is used. Since the CLSM optically sections the specimen, more than two images of the cross sections on and below the surface of the composite can be obtained. Three‐dimensional fiber orientation states can be determined by using geometric parameters of fiber images obtained from two parallel cross sections. For experiments, carbon‐fiber‐reinforced polystyrene is examined by the CLSM and geometric parameters of fibers on each cross‐sectional plane are measured by an image analysis. In order to describe fiber orientation states compactly, orientation tensors are determined at different positions of the prepared specimen. Three‐dimensional orientation states are obtained without any difficulty by determining the out‐of‐plane angles utilizing fiber images on two parallel planes acquired by the CLSM. Orientation states are different at different positions and show the shell–core structure along the thickness of the specimen. Fiber orientation tensors are predicted by a numerical analysis and the numerically predicted orientation states show good agreement with measured ones. However, some differences are found at the end of cavity. They may result from the fountain flow effects, which are not considered in the numerical analysis. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 88: 500–509, 2003     

利用信息融合方法的三维特征提取

本文提出了一种基于信息融合的物体三维特征的提取方法，该方法利用两幅互相配准的三维测距图像和灰度图像，来提取多面体的三维特征。首先，通过分析灰度图像中的灰度变化及测距图像中的测距值变化，分别求取各自图像中物体的特征点及特征边；然后，利用两配准图像之间的对应关系，求得所有特征点、面与多边形在三维测距图像中的三维表示；接着，通过分析三维测距图像中所测得的各候选平面上特定点与边处的曲率及法向，验证候选平面