Prediction of brittle-to-ductile transitions in polystyrene

In this study it is attempted to predict brittle-to-ductile transitions (BDTs) in polystyrene blends, induced either by an increase in temperature or by a decrease in inter-particle distance. A representative, two-dimensional volume element (RVE) of a polystyrene matrix with 20% circular voids, is deformed in tension. During deformation a hydrostatic-stress based craze-nucleation criterion [1] is evaluated. The simulations demonstrate that crazes initiate at low temperatures while a transition from crazing to shear yielding (BDT) is found around 75 °C. The numerical results correlate well with tensile tests on similar heterogeneous polystyrene. The presence of an absolute length, as experimentally found, is more difficult to explain. Near a free surface a T_g-depression is measured for polystyrene and also the resistance to indentation in polystyrene is lower than expected from bulk properties. Both observations are rationalised by an enhanced segmental mobility of chains near a free surface. As a consequence of these findings, an absolute length-scale could be incorporated in the numerical simulations. For simplicity, the length-scale is modelled by taking a temperature gradient over a thin layer near the internal free surfaces of the RVE. Deformation of the RVE with different absolute length-scales shows that indeed also the experimentally found brittle-to-ductile transition can be predicted if the ligament thickness between the inclusions (‘voids’) in polystyrene is below a critical value of ca. 15 nm.     

Nonlinearity analysis and optimization of HBTs for optical mixer designs

Two types of photo heterojunction bipolar transistor (HBT) to directly down-convert optical signals to electronic signals have been reported in the literature: a conventional photo-HBT in which light penetrates through the area of the base-collector junction and an HBT where light shines through the base-collector edge for higher conversion efficiency. Although the performance in relation to bias conditions has been published, the detailed analyses for identifying the parameters and bias conditions that provide optimum direct down-conversion have not been examined. This paper provides a full explanation of the operation of the down-conversion for both HBT configurations based on low-frequency analyses. Such information is useful for both understanding the nonlinear mechanisms involved and designing for maximum efficiency. In addition, a new circuit has been developed from the basic HBT down-conversion circuit that provides improved performance.     

Formulation of a ceramic ink for a wide-array drop-on-demand ink-jet printer

This paper describes the methodology for simulating a reprographic ink with a ceramic ink based on a commercially available zirconia powder for direct ceramic ink-jet printing. Of over-riding importance was matching viscosity and this was tested systematically by using a mineral oil–hexane binary system. Of secondary importance was adjustment of the pressure defect behind the nozzle to compensate for small differences in surface tension. The inks tested in the wide array print-head were based on low electrical conductivity liquids to avoid damage to the electroding system. The organic binder for the zirconia ink was paraffin wax and the dispersant was a hydroxystearic acid based polyester.     

A decision support system for interactive decision making - Part II: analysis and output interpretation

For pt.I see ibid., p.42-55 (2003). The development of a comprehensive decision support system, GMCR II, for the systematic study of real-world interactive decision problems is presented. The companion paper (Part I), discusses how GMCR II elicits, stores, and manages conflict models; here (Part II), the focus is on GMCR IIs analysis and output interpretation subsystems. Specifically, this paper describes the powerful and efficient analysis engine contained in GMCR II, its informative output presentation and interpretation facilities, and a number of follow-up analyses. Furthermore, an illustrative case study is used to demonstrate how GMCR II can be conveniently applied in practice.     

Finding all hops shortest paths

In this letter, we introduce and investigate a new problem referred to as the All Hops Shortest Paths (AHSP) problem. The AHSP problem involves selecting, for all hop counts, the shortest paths from a given source to any other node in a network. We derive a tight lower bound on the worst-case computational complexities of the optimal comparison-based solutions to AHSP.     

Analysis of an extensive measurement program developed from the start up to the follow up of the operation of the CNAAA NPP

Integrated tests (IT) applied to the Units I and II of the CNAAA Nuclear Power Plants (Angra dos Reis, Rio de Janeiro, Brazil) vara part of a comprehensive test program required to have the commercial operational licence issued. The IT cover operation at zero power and the subsequent power levels (the power escalation) until the nominal power operation.

This paper reports and compares the results of systematic neutron and gamma equivalent dose-rate measurements performed inside and outside the reactor containment of each Unit, during the start-up phase of the operation, for different power levels of the reactors. It also compares the collective-doses measured along the operation of the two units of the CNAAA wich similar data of the Grafenrheinfeld nuclear power plant (Germany) — basic-of-project for the CNAAA — Unit II — and analyses the data under the fight of the state-of-art.     

Control system design on a power-split CVT for high-power agricultural tractors

The problem considered in this paper is the design and tuning of the control system of a power-split continuously variable transmission (CVT) used in high-power tractors. Power-split CVTs are characterized by the combination of a traditional mechanical transmission and by a continuously-variable transmission. This guarantees, at the same time, smooth variations of the transmission-ratio and high efficiency of the overall transmission system. The control architecture of an hydrostatic power-split CVT is constituted by three main parts: 1) servo-controller on the current of the valve which drives the hydraulic transmission; 2) a servo-controller on the hydraulic transmission-ratio; and 3) a synchronizer which coordinates the hydraulic and the mechanical parts of the CVT. In this work, these three controllers are fully developed, including: design, implementation, and evaluation on an experimental system.     

On-demand learning for a wireless campus

The current Internet and wireless networks are harsh environments for transporting high-bandwidth multimedia data. We examine the technical issues involved, and describe an end-to-end solution to support a Web-based learn-on-demand system that operates in a wireless campus environment.     

Sensitive Mother-to-Adolescent Disclosures After Divorce: Is the Experience of Sons Different From That of Daughters?

This study addressed two main questions: (a) Are adolescent sons and daughters exposed to sensitive maternal disclosures after divorce with similar frequency and in similar detail? and (b) Does gender act as a moderator in the association between maternal disclosures and adolescent adjustment difficulties? Forced-choice and open-ended data were collected from 194 adolescents within 2 years after their parents' divorce. Quantitative analyses revealed that although the majority of adolescents experience some level of maternal disclosure, neither frequency nor detail of maternal disclosure differed as a function of adolescent gender. Frequent and detailed maternal disclosures were associated with adolescent adjustment difficulties, primarily psychological distress. Gender did not moderate that significant association. Qualitative analysis shed light on the link between maternal disclosures and adolescent distress, suggested the importance of how disclosures are made, and revealed several gender differences in reactions to maternal disclosures. Implications of the findings are discussed. (PsycINFO Database Record (c) 2010 APA, all rights reserved)     

Practical OSPF traffic engineering

Open Shortest Path First (OSPF) traffic engineering (TE) is intended to bring long-awaited traffic management capabilities into IP networks, which still rely on today's prevailing routing protocols: OSPF or IS-IS. In OSPF, traffic is forwarded along, and split equally between, equal cost shortest paths. In this letter, we formulate the basic requirements placed on a practical TE architecture built on top of OSPF and present a theoretical framework meeting these requirements of practicality. The main contribution of our work comes from the recognition that coupled with an instance of the maximum throughput problem there exists a related inverse shortest-path problem yielding optimal OSPF link weights.