The influence of incident angle, object colour and distance on CNC laser scanning

This article examines the influence of incident angle, object colour and measurement distance on the computer numerically controlled laser scanning process. To determine the physical background of these influences, the operation of the triangulation sensor, the surface reflection and the colour properties of the measured object were analysed. The various influences and their physical background are explained by using a test-measurement setup, which makes it possible to investigate a specific influencing factor. The article concludes with several guidelines that should be followed in order to obtain better measurement results.     

A characterisation of thick film resistors for strain gauge applications

Some commercial thick film resistors with sheet resistivities from 1 kohm/sq. up to 1 Mohm/sq. were evaluated for strain gauge applications. Temperature coefficients of resistivity, noise indices and gauge factors (GFs) were measured. For the same resistor series GFs and noise indices increase with increasing sheet resistivity. However, both GFs and noise indices are different for resistors with the same nominal sheet resistivity but from different resistor series. The results indicated that the microstructure rather than the different chemical composition of the conductive phase in thick film resistors is the primary reason for the different gauge factors.     

Microstructural, XRD and electrical characterization of some thick film resistors

The microstructural and electrical characteristics (sheet resistivities, TCRs, and noise indices) of some 1 k/sq. and 10 k/sq. thick films were evaluated. The conductive phase was determined by X-ray diffraction (XRD) analysis. The microstructures of fired resistors were investigated by scanning electron microscopy (SEM) and analyzed by energy dispersive spectrometry (EDS). Some resistors were fired for a relatively long time at the highest temperature, i.e., 6 h at 850 °C, to allow the reactions in the material to reach equilibria. Sheet resistivities, temperature coefficients of resistivity, and noise indices of these resistors were compared with normally (10 min at 850 °C) fired resistors. After 6 h firing absolute temperature coefficient of resistivity (TCR) values of most resistors increased significantly, while sheet resistivities decreased. Complex impedance analysis showed that in most cases resistors with low noise indices showed nearly ideal resistor response while those with higher noise had a larger imaginary part.     

Permutation routing in double-loop networks: design and empirical evaluation

A double-loop network is an undirected graph whose nodes are integers 0,1,…,n−1 and each node u is adjacent to four nodes u±h₁(mod>n), u±h₂(mod>n), where 0<h₁<h₂<n/2. There are initially n packets, one at each of the n nodes. The packet at node u is destined to node π(u), where the mapping uπ(u) is a permutation. The aim is to minimize the number of routing steps to route all the packets to their destinations. If ℓ is the tight lower bound for this number, then the best known permutation routing algorithm takes, on average, 1.98ℓ routing steps (and 2ℓ routing steps in the worst-case).Because the worst-case complexity cannot be improved, we design four new static permutation routing algorithms with gradually improved average-case performances, which are 1.37ℓ, 1.35ℓ, 1.18ℓ, and 1.12ℓ. Thus, the best of these algorithms exceeds the optimal routing by at most 12% on average.To support our algorithm design we develop a program which simulates permutation routing in a network according to the given topology, routing model as well as communication pattern and measure several quality criteria. We have tested our algorithms on a large number of double-loop networks and permutations (randomly generated and standard).     

A large-displacement 65Pb(Mg1/3Nb2/3)O3–35PbTiO3/Pt bimorph actuator prepared by screen printing

In this paper we present a novel approach to preparing large-displacement 65Pb(Mg_1/3Nb_2/3)O₃–35PbTiO₃/Pt (65/35 PMN–PT/Pt) bimorph actuators. These “substrate-free”, bending-type actuators were prepared by screen-printing the 65/35 PMN–PT and Pt thick-film pastes as the electrodes on alumina substrates. After this screen printing and the subsequent firing the 65/35 PMN–PT/Pt composites were peeled off from the substrates. Displacements of nearly 100 μm at 18 V were achieved for actuators with dimensions of 1.8 cm × 2.5 mm × 50 μm for the 65/35 PMN–PT layer. The normalized displacement (the displacement per unit length) was 40 μm/cm at 18 V. The experimental results together with a computation procedure were used to obtain the material parameters for a finite-element analysis of the 65/35 PMN–PT/Pt bimorph actuators.     

Self-adaptive differential evolution algorithm using population size reduction and three strategies

Many real-world optimization problems are large-scale in nature. In order to solve these problems, an optimization algorithm is required that is able to apply a global search regardless of the problems’ particularities. This paper proposes a self-adaptive differential evolution algorithm, called jDElscop, for solving large-scale optimization problems with continuous variables. The proposed algorithm employs three strategies and a population size reduction mechanism. The performance of the jDElscop algorithm is evaluated on a set of benchmark problems provided for the Special Issue on the Scalability of Evolutionary Algorithms and other Metaheuristics for Large Scale Continuous Optimization Problems. Non-parametric statistical procedures were performed for multiple comparisons between the proposed algorithm and three well-known algorithms from literature. The results show that the jDElscop algorithm can deal with large-scale continuous optimization effectively. It also behaves significantly better than other three algorithms used in the comparison, in most cases.