Controlled undercooling of liquid iron in contact with ZrO2 and MgO substrates under varying oxygen partial pressures

The objective of this study is to determine the conditions under which the inclusions present in liquid steel can act as heterogeneous nucleants for solidification. In order to study the factors that define the undercooling of a given metal/oxide couple, the undercooling of a pure iron sessile droplet in contact with Al₂O₃, ZrO₂, and MgO substrates was measured under controlled oxygen partial pressures by observing droplet recalescence. The results showed that the undercooling of iron, in contact with a particular substrate, did not have a unique value, but was significantly affected by the oxygen content on the gas phase. For oxygen partial pressures between 10⁻²¹ and 10⁻¹⁹, the undercooling of iron on ZrO₂ substrates was stable and around 290 °C. In the same range of oxygen partial pressure, the undercooling of iron on MgO substrates remained below 100 °C due to the low stability of this oxide. At lower oxygen contents, substrate decomposition might be the cause for the observed drop in the undercooling of iron on ZrO₂ substrates to below 100 °C. The undercooling also decreased for increasing oxygen content as verified when the gas was changed from gettered Ar/Ar-H₂ to CO/CO₂ mixtures. The variation in undercooling was related to the wetting of the substrate by the liquid metal, where the deep undercooling observed in the ZrO₂ experiments occurred when the highest contact angle between the liquid metal and the substrate was achieved.     

IPv6 delay and loss performance evolution

Although packet delay and loss are two important parameters of the Internet performance, to the best of our knowledge, the evolution of large‐scale IPv6 delay and loss performance has previously not been studied. In this paper, we analyze more than 600 end‐to‐end IPv6 paths between about 26 testboxes of RIPE Network Coordination Centre over two years, and compare the delay and loss performance over time with their IPv4 counterparts. We present and discuss the measurement methodologies and show that IPv6 paths have a higher delay and loss than their IPv4 counterparts. The main reason for the worse performance stems from IPv6‐in‐IPv4 tunnels rather than from native IPv6 paths and such tunnels are still widely used today. Copyright © 2007 John Wiley & Sons, Ltd.     

Biaxiale Ermüdung reibrührgeschweißter Strukturelemente

Biaxial fatigue of friction stir welded stiffened panels Within the framework of the European WelAir project, cruciform specimens made from stiffening FSW overlap joints were fatigued in the DLR biaxial test rig. To resemble the loading situation of pressurized fuselage structures, proportional loading without any phase shift, but with different load ratios λ between the loading components in both directions was applied.Natural crack initiation and subsequent crack growth were governed by the stiffness gradient caused by introducing the stringer. Cracks initiated and propagated at run‐in and run‐out locations in a direction perpendicular to the weld seam. The shortest fatigue life was observed for uniaxial loading in welding direction (λ = 0). An additional stress component perpendicular to the joint line (λ > 0) resulted in a higher number of cycles to failure. Similar to single stringer panels, increasing the load ratio also increased the number of cycles to failure for FSW clip‐stringer structural members, but additionally gives a different location of the fatal crack.     

ESR Refining Potential for Titanium Alloys using a CaF2‐based Active Slag

Since the end of the Cold War and due to the needs to produce titanium more cost‐efficient and thus more attractive for its civilian use, the electroslag remelting (ESR) process has become an increasingly important topic of international research programmes, because titanium and titanium aluminides can be chemically refined by ESR in some degree. Using ESR, titanium turnings from machining steps and scrap from foundries can be remelted, refined and provided as secondary titanium for the market at relatively favourable prices. This article investigates the removability of the main impurities out of titanium and titanium‐aluminium alloys by electroslag remelting using the active slag system CaF₂‐Ca‐(CaO). Thermochemical and kinetic aspects of the ESR process are considered.     

Deterministic finite automata with recursive calls and DPDAs

We study deterministic finite automata (DFA) with recursive calls, that is, finite sequences of component DFAs that can call each other recursively. DFAs with recursive calls are akin to recursive state machines and unrestricted hierarchic state machines. We show that they are language equivalent to deterministic pushdown automata (DPDA).