Piezoresponse force microscopy characterization of rare-earth doped BiFeO3 thin films grown by the soft chemical method

The multiferroic behavior with ion modification using rare-earth cations on crystal structures, along with the insulating properties of BiFeO₃ (BFO) thin films was investigated using piezoresponse force microscopy. Rare-earth-substituted BFO films with chemical compositions of (Bi_1.00−xRE_xFe_1.00O₃ (x=0; 0.15), RE=La and Nd were fabricated on Pt (111)/Ti/SiO₂/Si substrates using a chemical solution deposition technique. A crystalline phase of tetragonal BFO was obtained by heat treatment in ambient atmosphere at 500 °C for 2 h. Ion modification using La³⁺ and Nd³⁺ cations lowered the leakage current density of the BFO films at room temperature from approximately 10⁻⁶ down to 10⁻⁸ A/cm². The observed improved magnetism of the Nd³⁺ substituted BFO thin films can be related to the plate-like morphology in a nanometer scale. We observed that various types of domain behavior such as 71° and 180° domain switching, and pinned domain formation occurred. The maximum magnetoelectric coefficient in the longitudinal direction was close to 12 V/cm Oe.     

Linear viscoelastic behavior of compatibilized PMMA/PP blends

In this work, the morphology and linear viscoelastic behavior of PMMA/PP blends to which a graft copolymer PP‐g‐PMMA has been added was studied. The copolymer concentration varied from 1 to 10 wt % relative to the dispersed phase concentration. The rheological data were used to infer the interfacial tension between the blended components. It was observed that PP‐g‐PMMA was effective as a compatibilizer for PMMA/PP blends. For PP‐g‐PMMA concentration added below the critical concentration of interface saturation, two rheological behaviors were observed depending on the blend concentration: for 70/30 blend, the storage modulus, at low frequencies, increased as compared to the one of the unmodified blend; for 90/10 blend, it decreased. For 90/10 blend, the relaxation spectrum presented an interfacial relaxation time related to the presence of the compatibilizer (τ_β). For PP‐g‐PMMA concentrations added above the critical concentration of interface saturation, the storage modulus of all blends increased as compared with the one of the unmodified blend. © 2012 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2013     

From coffee industry waste materials to skin‐friendly products with improved skin fat levels

Spent coffee grounds (SCG), which are the residue obtained from the treatment of coffee with hot water or steam, can be used for industrial applications, due to the high content in lipids. The cosmetic products might be a suitable application for these types of residues because the barrier properties of the stratum corneum (SC) are largely dependent on the intactness of the lipid lamellae that surrounds the corneocytes. The purpose of this work was to assess the feasibility of using the lipid fraction of SCG extracted with supercritical carbon dioxide in the development of new cosmetic formulations with improved skin lipids (sebum) and hydration. The use of spent coffee lipid extract in cosmetic industry seems to be a suitable approach to recycle the wastes from coffee industry. Emulsion containing 10% of the lipid fraction of SCG (SpentCofOil cream) presented promising characteristics in the improvement of sebum skin levels with a good acceptance by consumers when compared to an emulsion containing 10% w/w of green coffee oil (GreenCofOil cream) and a placebo without coffee oil (NoCofOil cream). Practical applications: In this work, the authors develop and characterize a cream containing 10% of the lipid fraction of SCG extracted with supercritical carbon dioxide with improved skin lipids (sebum) and hydration.     

Mode II Fracture Toughness of a Brittle and a Ductile Adhesive as a Function of the Adhesive Thickness

The main goal of this study was to evaluate the effect of the thickness and type of adhesive on the Mode II toughness of an adhesive joint. Two different adhesives were used, Araldite ® AV138/HV998 which is brittle and Araldite 2015 which is ductile. The end notched flexure (ENF) test was used to determine the Mode II fracture toughness because it is commonly known to be the easiest and widely used to characterize Mode II fracture. The ENF test consists of a three-point bending test on a notched specimen which induces a shear crack propagation through the bondline. The main conclusion is that the energy release rate for AV138 does not vary with the adhesive thickness whereas for Araldite 2015, the fracture toughness in Mode II increases with the adhesive thickness. This can be explained by the adhesive plasticity at the end of the crack tip.     

Effect of Immersion Time in Osmosis and Ultrasound on Papaya Cell Structure during Dehydration

The effect of ultrasound-assisted osmotic dehydration applied at atmospheric pressure for different lengths of time on papaya tissue structure was evaluated. Ultrasound induced the loss of cellular adhesion, formation of large cell interspaces, and light rupture of the cell walls. The changes in the tissue structure caused by ultrasound application increased sugar loss, water loss, and effective water diffusivity. Ultrasound-assisted osmotic dehydration induced a gradual distortion in the shape of the cells, loss of cellular adhesion, and the formation of large channels caused by rupture of the cell walls. The changes caused by the application of osmotic dehydration resulted in high water loss and sugar gain.     

High-Area Ti/Pt Electrodes for the Electrochemically Catalyzed Transesterification of Soybean Oil with Methanol

Biodiesel fuel is a renewable energy source normally produced in industry by using an alkaline homogeneous catalyst to promote the transesterification of oil and methanol to fatty acid methyl ester (FAME). Undesirable side reactions occur when poorly refined oils are used, leading to serious problems of product separation and low FAME yield. Therefore, about 85% of the cost of biodiesel is determined by the cost of the feedstock. Here, we describe the development of high-area Pt films deposited on Ti substrates for the electrolytic synthesis of biodiesel from soybean oil containing water, without the addition of catalyst. The higher both the calcination temperature and the number of layers deposited on the Ti surface, the higher the electrochemically active area of Pt exposed to surface. Conversion into esters in electrolysis is proportional to the increase in the superficial area of the Ti/Pt electrodes. Thus, it is possible to synthesize biodiesel using electrodes containing very low amounts of Pt (<0.441 mg cm^?2), an important parameter in the industrial production of biodiesel.     

Transport of Dissolved Si from Soil to River: A Conceptual Mechanistic Model

This paper reviews the processes which determine the concentrations of dissolved silicon (DSi) in soil water and proposes a conceptual mechanistic model for understanding the transport of Si through soils to rivers. The net DSi present in natural waters originates from the dissolution of mineral and amorphous Si sources in the soil, as well as precipitation processes. Important controlling factors are soil composition (mineralogy and saturated porosity) and soil water chemistry (pH, concentrations of organic acids, CO₂ and electrolytes). Together with production, polymerization and adsorption equations they constitute a mechanistic framework determining DSi concentrations. We discuss how key controls differ across soil horizons and how this can influence the DSi transport. A typical podzol soil profile in a temperate climate is used as an example, but the proposed model is transferrable to other soil types. Additionally, the impact of external forcing factors such as seasonal climatic variations and land use is evaluated. This blueprint for an integrated model is a first step to mechanistic modelling of Si transport processes in soils. Future implementation with numerical methods should validate the model with field measurements.     

SUPERCRITICAL EXTRACTION OF LINSEED OIL: ECONOMICAL VIABILITY AND MODELING EXTRACTION CURVES

The aim of the present study was to use supercritical technology to recover linseed oil (Linum usitatissimum L.) using carbon dioxide (alone or modified with ethanol as solvent) to determine the influence of the technique on the chemical composition of the oil obtained, model the kinetic curves of extraction, and estimate the manufacturing cost of the process. The experiments were conducted at 323 K, pressure of 25 MPa, constant solvent flow of 1.7 × 10^?5 kg/s, and extraction time of 5 h. The highest yield was obtained with the addition of cosolvent (28.8%). The SFE process of linseed oil manufacture proved to be economically viable, resulting in a product with a specific cost of 13.21 US$/kg_oil. As to oil composition, the main fatty acids detected were linolenic and oleic acid.     

Effect of Solvent Content on the Separation and the Energy Consumption of Extractive Distillation Columns

This article sets out to evaluate the effect of solvent content in the extractive section on the separation efficiency and energy consumption of extractive distillation columns. Contrary to the classical approach, the proposed approach enables a simultaneous evaluation of the effect of the major decision variables (reflux ratio, solvent flow rate, and the number of stages of the extractive section [NSE]). The procedure allows calculating the minimum solvent flow rate for the separation and the minimum specific energy consumption. The results show that the minimum specific energy consumption is obtained for the minimum reflux ratio and not for the minimum solvent flow rate. Moreover, the results show that it is not always the case that a larger NSE results in lower energy consumption. Due to its industrial importance, the dehydration of aqueous mixtures of ethanol using ethylene glycol as solvent has been chosen as a case study.     

Comparative electrochemical studies of zinc chromate and zinc phosphate as corrosion inhibitors for zinc

The anticorrosive performance of two inhibitive pigments, zinc chromate and zinc phosphate, was compared using electrochemical impedance spectroscopy (EIS) and the scanning vibrating electrode technique (SVET) in pigment extracts in 0.1 M NaCl. It was observed that zinc was protected from corrosion in both extracts. In tests using hot dip galvanised steel painted with an epoxy primer incorporating the pigments, the SVET detected the anodic and cathodic distribution along the scribes, although no significant differences were observed among the various primers. On the contrary, EIS was able to distinguish processes occurring on the metal surface exposed by the scribe in different samples. For primers with anticorrosive pigment, a time constant at high frequencies was attributed to a layer of protective nature, probably formed by metal ions from the substrate and inhibitive ions leached from the anticorrosive pigments.