Dynamic experimental simulation of hydrogen oriented underground gasification of lignite

The main goal of the study presented in the paper was to experimentally demonstrate the feasibility of lignite gasification to hydrogen-rich gas under the underground conditions simulated in the ex situ reactor. The in situ gasification conditions were simulated both in respect to the coal seam and the surrounding stratum. In the 54-h experiment the process of lignite gasification with oxygen and steam as gasifying medium was tested. The experiment was initially divided into three stages: the ignition stage, the oxygen stage and the steam stage.The gas produced in the steam gasification stage was characterized by the calorific value of 7.8 MJ/m³ and average hydrogen content of 46.3 vol.%. Unfortunately a rapid decrease in the temperature levels and in the amount of produced gas proved that the tested lignite of 53 vol.% moisture content was not suitable for steam gasification. A great amount of thermal energy was consumed for water evaporation which led to a considerable heat loss. An addition of stoichiometric amount of water in the system by adding steam caused the seam to extinguish. Thus only oxygen could be used as the gasifying medium in the gasification of the tested lignite. The average calorific value of gas produced in the stable operation during oxygen gasification stage equaled 5.2 MJ/m³ with the average gas production rate of 16.0 m³/h and the average hydrogen content in the produced gas of 26.4 vol.%.     

Novel N‐ethyl‐2‐styrylquinolinium iodides as sensitizers in the photoinitiated free‐radical polymerization of trimethylolopropane triacrylate. II

Results of kinetic studies of two‐component photoinitiator systems used in the visible‐light photoinduced polymerization of 2‐ethyl‐2‐(hydroxymethyl)‐1,3‐propanediol triacrylate are presented. Nine different styrylquinolinum dyes coupled with n‐butyltriphenylborate as a coinitiator have been used as photoinitiating systems. Reactive radicals that initiate the polymerization are formed by the well‐known mechanism of photoinduced electron transfer between dye cations acting as electron acceptors and borate anions acting as electron donors. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

Effect of chirality, release rate, and host volatiles on response of Tetropium fuscum (F.), Tetropium cinnamopterum Kirby, and Tetropium castaneum (L.) to the aggregation pheromone, fuscumol

The male-produced aggregation pheromones of Tetropium fuscum (F.) and T. cinnamopterum Kirby were identified as (2S,5E)-6,10-dimethyl-5,9-undecadienol by chemical analysis, synthesis, electronantennography, and field trapping; the compound is here renamed “fuscumol”. The effect of fuscumol chirality, alone or with host volatiles, and fuscumol release rate on Tetropium spp. was tested in field-trapping experiments in Nova Scotia and Poland. Both (S)-fuscumol and racemic fuscumol synergized trap catches of male and female T. fuscum, T. cinnamopterum, and T. castaneum (L.) when combined with a blend of host monoterpenes and ethanol. Without added host volatiles, fuscumol was either unattractive (in Nova Scotia) or only slightly so (in Poland). (R)-Fuscumol, alone or in combination with host volatiles, did not elicit increases in trap capture of any Tetropium species, relative to the controls. Fuscumol synergized attraction of both sexes to host volatiles, thus indicating it acts as an aggregation pheromone. Sex ratio was often female-biased in traps baited with fuscumol plus host volatiles, and was either unbiased or male-biased in traps with host volatiles alone. In traps with host volatiles and racemic fuscumol, mean catches of Tetropium species were unaffected by fuscumol release rates ranging from 1 to 32 mg/d. The attraction of three different Tetropium species to the combination of (S)-fuscumol and host volatiles suggests that cross-attraction may occur where these species are sympatric, and that reproductive isolation possibly occurs via differences in close-range cues. These results have practical applications for survey and monitoring of T. fuscum, a European species established in Nova Scotia since at least 1980, and for early detection of T. castaneum, a European species not presently established in North America.     

The kinetics of coal chars hydrogasification

Hydrogasification reaction of chars produced from two rank coals was investigated in temperature up to 1173 K and pressure up to 8 MPa. The reactivity of the lignite Szczerców char has been found to be slightly higher than of the subbituminous coal Janina char produced at the same conditions. A high value of the char reactivity was observed to certain carbon conversion, above which a sharp drop takes place. It has been shown that to achieve proper carbon conversion the hydrogasification reaction must proceed at temperature above 1200 K. Based on the active centres theory the kinetic equations of the hydrogasification process were developed and the kinetic constants at the maximum reaction rate evaluated for the analyzed chars.     

Electropolishing and passivation of NiTi shape memory alloy

Electropolishing of NiTi alloy has been investigated. The influence of polishing bath composition and the operating conditions instead of the conditions of the process on the quality of the surface, evaluated by AFM and SEM methods, was established. Morphologically uniform surfaces were obtained only in the case of solutions containing hydrofluoric and sulfuric acids. Electropolished samples were sterilized and thermally passivated, then their corrosion resistance was measured in Tyrode's physiological solution. It was established that already after the electropolishing the corrosion resistance of NiTi alloy increases due to the spontaneously formed TiO₂ layer. The increase of the thickness of the layer during sterilization and thermal passivation causes further increase in the corrosion resistance.     

Dielectric,Mechanical, and Thermal Properties of Low-Permittivity Polymer–Ceramic Composites for Microelectronic Applications

A new low-permittivity polymer–ceramic composite for packaging applications has been developed. The ceramic-reinforced polyethylene and polystyrene composites were prepared by melt mixing and hot molding techniques. Low-loss, low-permittivity Li₂MgSiO₄ (LMS) ceramics prepared by the solid-state ceramic route were used as the filler to improve the dielectric properties of the composites. The relative permittivity and dielectric loss were increased with the increase in the ceramic loading at radio and microwave frequencies. The mechanical properties and thermal conductivity of the Li₂MgSiO₄-reinforced polymer–ceramic composite were also investigated. The stability of the relative permittivity of polymer–ceramic composites with temperature and frequency was investigated. The experimentally observed relative permittivity, thermal expansion, and thermal conductivity were compared with theoretical models.     

Congener-specific carbon isotopic analysis of technical PCB and PCN mixtures using two-dimensional gas chromatography-isotope ratio mass spectrometry

Analysis of stable carbon isotope fractionation is a useful method to study the sources and fate of anthropogenic organic contaminants such as polychlorinated biphenyls (PCBs) in the environment. To evaluate the utility of carbon isotopes, determination of isotopic ratios of 13C/12C in source materials, for example, technical PCB preparations, is needed. In this study, we determined delta13C values of 31 chlorobiphenyl (CB) congeners in 18 technical PCB preparations and 15 chloronaphthalene (CN) congeners in 6 polychlorinated naphthalene preparations using two-dimensional gas chromatography-combustion furnace-isotope ratio mass spectrometry (2DGC-C-IRMS). Development of 2DGC-IRMS enabled improved resolution and sensitivity of compound-specific carbon isotope analysis (CSIA) of CB or CN congeners. Delta13C values of PCB congeners ranged from -34.4 (Delors) to -22.0/1000 (Sovol). Analogous PCB preparations with similar chlorine content, but different geographical origin, had different delta13C values. PCB preparations from Eastern European countries--Delors, Sovol, Trichlorodiphenyl, and Chlorofen--had distinct delta13C values. PCB mixtures showed increased 13C depletion with increasing chlorine content. Delta13C values for individual CB congeners varied depending on the degree of chlorination in technical mixtures. Delta13C values of CN congeners in Halowaxes ranged from -26.3 to -21.7/1000 and these values are within the ranges observed for PCBs. This study establishes the range of delta13C values in technical PCB and PCN preparations, which may prove to be useful in the determination of sources of these compounds in the environment. This is the first study to employ 2DGC-IRMS analysis of delta13C values in technical PCB and PCN preparations.     

A microporous and high surface area active carbon obtained by the heat-treatment of chitosan

A method is described for converting chitosan into a high surface area and porous active carbon using a Na₂CO₃ solution impregnated into a partly depolymerized, protonated and water soaked chitosan. The wet chitosan paste is heat treated and transformed into a nonporous solid i.e. a carbon-rich matrix with uniformly suspended Na₂CO₃ nanocrystallites. Subsequent HCl etching opens cavities in the matrix due to the removal of the Na₂CO₃. The active carbon is high surface area (above 400 m²/g), microporous (below 1 nm) and nitrogen-rich (above 6% atomic).