转炉冶炼20管坯钢生产实践

介绍了20#管坯钢的生产试验工艺，采取了拉碳法脱碳、钢包底吹氩及喂丝、保护浇铸、合理控制拉速等有效措施，解决了生产中存在的质量问题，为下一步的生产提供了理论和实践依据。     

第三方物流企业信息化问题研究

探讨了物流信息化的基本概念及其主要内容，并就其对第三方物流企业的作用进行了阐述。最后以安泰物流信息化建设为案例讲述了具体的第三方物流企业信息化建设。     

LD-LF-CC生产45^#质量研究与实践

莱钢采用LD-LF-CC（方坯连铸）生产45^#钢铸坯质量存在较多问题,主要是表面气孔数量多、轧材顶锻裂纹等。从对顶锻裂纹缺陷进行金相分析、扫描电镜分析出发,研究45^#钢铸坯表面气孔形成的原因;生产实践中,通过采取控制钢中气体含量的措施,使45^#钢铸坯质量得到全面改善。     

剖析半悬挂减速机故障的产生与对策

介绍了半悬挂减速机的工作原理，分析其故障原因，实施相应的解决对策。     

VHF-PECVD制备微晶硅材料的均匀性及其结构特性的分析

采用VHF-PECVD技术在多功能系统(cluster tool)中制备了系列硅薄膜，研究薄膜的均匀性及电学特性和结构特性。结果表明：气压和功率的合理匹配对薄膜的均匀性有很大的影响；材料的喇曼测试和电学测试结果表明微晶硅薄膜存在着纵向的结构不均匀，在将材料应用于器件上时，必须要考虑优化合适的工艺条件；硅烷浓度大，相应制备薄膜的晶化程度减弱，即薄膜中非晶成分增多。     

灯泡贯流泵装置的基本流态分析

为了回答灯泡贯流泵装置中的灯泡体究竟应该前置还是应该后置的问题,应用水泵装置三维湍流数值模拟的方法分别研究了南水北调东线工程某泵站前置灯泡和后置灯泡贯流泵装置两个不同方案的流态,揭示了前置灯泡和后置灯泡贯流泵装置的基本流动属性;数值模拟的结果得到流道模型试验的验证。研究结果表明:前置灯泡贯流泵装置的进、出水流态均匀平顺,水力损失较小;后置灯泡贯流泵装置的进水流态均匀平顺,但出水流道内存在明显的偏流和旋涡流动,水力损失较大;灯泡体前置符合水力学的基本原理,是获得最佳灯泡贯流泵装置水力性能的必要条件之一。     

三嗪类化合物的合成及其产酸性能研究

合成了一系列的三嗪类光生酸剂1a-1e，确定了它们的结构，并对1e在乙腈溶剂中365和405nm光下的曝光分解产酸性能进行了初步的定量研究．结果表明，在测定浓度范围内分解量子产率和产酸量子产率基本上都不随浓度的变化而变化，在405nm光下比在365nm光下有更高的分解和产酸量子效率．有关这类化合物的光生酸性能与曝光波长的关系正在进一步研究中．     

医患和谐与建筑设计

我们经常会发现，同样一位医护人员在医院工作场所和在其它地方会表现出不同的性格特质，无论是多么和善的人，到了那种医院环境有时就表现得面目可憎。其实，倒不是个人特质有所改变，而是医疗机构流程的流水线和环境造成的，恶劣的医患关系也因此而愈发不可调和。     

Characterizing the deformation behavior of Tertiary sandstones

Tertiary sandstones possess deformational behavior different from hard rocks, especially the relatively larger amount of volumetric dilation during shearing. Such excess dilation contributes to the increase of crown settlement during tunnel excavation and accounts for several cases of tunnel squeezing within Tertiary sandstones. Therefore, the deformation behavior of Tertiary sandstones sampled from more than 13 formations was studied. To distinguish the volumetric deformation induced by hydrostatic stress or by shear stress as well as to decompose the elastic and the plastic components of strains, special experimental techniques, including pure shear tests and cycles of loading–unloading were applied.The experimental results reveal that the deformation of Tertiary sandstone exhibits the following characteristics: (1) significant amount of shear dilation, especially elastic shear dilation; (2) non-linear elastic and plastic deformation; (3) plastic deformation occurs prior to the failure state. Furthermore, features of plastic deformation were inferred from experimental results and, as a result, the geometry of plastic potential surface and the hardening rule were accordingly determined. A constitutive model, involving nonlinear elastic/plastic deformation and volumetric deformation induced by shear stress, is proposed. This proposed model simulates the deformational behavior for the shear-dilation-typed rocks reasonably well. Furthermore, tests on the versatility of the proposed model, including varying hydrostatic stress and stress paths, indicate that the proposed model is capable of predicting deformational behavior for various conditions.