浅析呼和浩特市大气SO2发展趋势及防治对策

本文通过对二氧化硫的形成及危害的阐述，以及对我市近几年大气中二氧化硫监测结果的分析，针对发展趋势和存在的问题，根据实际情况提出相应的建议。     

Effects of hydrogen on the transition layers between diamond films and Zr, Hf substrates

Highly purified polycrystalline wafers of Zr and Hf were chosen as substrates for diamond deposition by means of the d.c. arc discharge plasma CVD method. Polycrystalline diamond films were formed on both substrates. Scanning electron microscopy and high resolution X-ray diffraction were used to investigate the surface morphology of the diamond films and the composition of the interface layers between the diamond films and substrates. The experiments showed that the transition layer between the diamond films and Zr substrates was ZrC, ZrH and ZrC_0.32H_1.2. For Hf substrates, in addition to HfC, it is supposed that there were also some hydrides or carbohydrides in the transition layer, because several X-ray reflections appeared which could not be assigned to Hf, HfC or diamond.     

Preparation of Titanium Nitride/Alumina Laminate Composites

A preparation route for TiN/Al₂O₃ laminate composites has been described. A water-based process using Al₂O₃ and TiN slurries with solids contents of 40 and 35 vol%, respectively, was used to make TiN and Al₂O₃ tapes. The removal of the binder was monitored by weight-loss measurements in a thermogravimetry unit. Bodies composed of Al₂O₃ and TiN tapes were densified at temperatures of 1400° and 1500°C using the Spark Plasma Sintering^® (SPS) technique. Densities of >98% of the theoretical densities were approached. Crack-free and almost fully densified TiN/Al₂O₃ compacts were prepared by heating the burned-out green bodies to the final sintering temperature (1500°C) at a rate of 100°C/min, and with a holding time of 5–10 min, under a pressure of 75 MPa. The microstructures of the obtained compacts were studied using scanning electron microscopy. Grain sizes in the sintered Al₂O₃ and TiN compacts were similar to those of the precursor powders. Hardness and indentation fracture toughness were measured at room temperature, and the monolithic compacts as well as the laminate composites exhibited anisotropic mechanical behavior; i.e., the cracks propagated much more easily in a direction parallel to the laminas than perpendicular to them.     

CaSO_4晶须对聚氨酯胶粘剂性能影响的研究

用实验室自制的相对分子质量为2500的聚己二酸-1,4-丁二醇酯二醇和甲苯二异氰酸酯、混合扩链剂配制聚氨酯胶粘剂,并使用实验室自制的改性和未改性200nm硫酸钙晶须对聚氨酯胶粘剂进行改性,考察不同硫酸钙晶须及其加入量、加入方式对聚氨酯胶粘剂综合力学性能的影响。根据实验结果,200nm改性硫酸钙晶须当加入量为3％时,聚氨酯胶粘剂的拉伸强度、初粘性和最终剥离强度均有明显提高。     

Morphologies and microstructures of tree-like carbon produced at different reaction conditions in a CVD process

Centimeter-size multi-branched tree-like carbon structures have been generated by the catalytic chemical vapor deposition of toluene using ferrocene as the catalyst precursor and investigated by means of SEM, TEM, and EDX. It is found that a temperature of 1000-1200 °C and a carrier gas flow rate of 1000-2500 ml/min are necessary for the generation of the carbon trees. Their morphologies and microstructures change greatly with the changing reaction conditions. The fractal dimensions of the trees are calculated to quantitatively investigate the influence of different reaction temperatures on the morphologies.     

轻质多孔复合隔墙板挤压成型的研究与应用

〕介绍了轻质多孔复合隔墙板挤压成型机的构造原理、技术参数、使用方法与保养、经济分析和有关问题的探讨     

Phase Assemblages of Pr α-sialon Derived from SHS-ed Powders and TEM Study on the Nucleation of Pr α-sialon

The Pr α-sialon powders prepared by self-propagating high-temperature synthesis (SHS), consisting of 55 wt% Pr α-sialon and 45 wt% of β-sialon (abbreviated as α' and β'), were hot-pressed at 1800°C for 1 h. The results showed that Pr α' phase would transfer to β' with the appearance of JEM phase (Pr(Si_{6− z} Al _z )(N_{10− z} O _z )) after sintering, thus resulting in the increase of β' phase to 86 wt%. The addition of Y₂O₃ into SHS-ed Pr α' powders as the starting materials restrains the transformation of α' to β' and prevents the formation of JEM phase as well. The nucleation mechanism of Pr α' grain during hot-pressing was investigated in terms of transmission electron microscope and energy-dispersive spectrometer analysis. Two nucleation modes of Pr α' grains were found, i.e., nucleating on the undissolved Pr α' grains and on the nuclei of (Pr, Y) α' grains precipitated from liquid phase.     

对煤磨MDC89-7袋式除尘器的节能环保改造

0 前言 湖南韶峰水泥集团有限公司规格为φ2.5 m×3.9 m的风扫式煤磨配套的MDC89-7袋式除尘器于1993年投用,经十多年的生产应用,其导流板及风道损坏达80%左右;外壳、主风道因烧袋和腐蚀,严重变形且花板变得很薄;反吹风道变形穿孔,提升阀密封不严,导致清灰时风量流失严重,运行阻力增加,系统产量降低,且系统中含氧量增加,带来安全隐患;除尘效率下降、污染严重,粉尘排放浓度高达1 g/m3;系统能耗高,且维修强度大(每个滤袋重50kg,每次换袋需12人)且费用高.为此,该公司于2004年4月对该煤磨除尘器进行技术改造,取得了明显的效果.     

Electrochemical micromachining of nitinol by confined-etchant-layer technique

The confined etchant layer technique has been applied to fabricate complex three-dimensional microstructures on nitinol for the first time. HF and HNO₃ were locally and simultaneously electrogenerated at the mold surface to etch a nitinol workpiece. NaOH was used as an efficient scavenger to confine the etchant close to the mold. Cyclic voltammetry was employed to study the electrochemical behavior of a Pt electrode in the etching solution in order to choose an appropriate potential for etchant generation on the mold. The thickness of the confined etchant layer was estimated to be several micrometers by inspecting the deviation of the sizes of the etched spots from the sizes of those on the microelectrode. Thus, the composition of the electrolyte could be optimized for better etching precision. By optimizing the composition of the electrolyte, complex microstructures on a Pt-Ir mold bearing the logo “XMU” of Xiamen University were successfully fabricated on nitinol. The etched patterns were approximately negative copies of the mold, and the precision of duplication could easily reach the micrometer scale.     

To accelerate shot boundary detection by reducing detection region and scope

Video Shot Boundary Detection (SBD) is the fundamental process towards video summarization and retrieval. A fast and efficient SBD algorithm is necessary for real-time video processing applications. Extensive work has focused on accurate shot boundary detection at the expense of demanding computational costs. In this paper, we propose a fast SBD approach that reduces the computation pixel-wise and frame-wise while still giving satisfactory accuracy. The proposed approach substantially speeds up the computation through reducing both detection region and scope. Color histogram and mutual information are used together to measure the difference between frames. Corner distribution of frames is utilized to exclude most of false boundaries. We conduct extensive experiments to evaluate the proposed approach, and the results show that our approach can not only speed up SBD, but also detect shot boundaries with high accuracy in both Cut (CUT) and Gradual Transition (GT) boundaries.