Analysis of the detectivity for triple-layer heterojunction GaSb/GaInAsSb infrared detectors

In this paper, the detectivity is calculated and analyzed with the front-or backside illuminated case for both N-GaSb/p₂-Ga_0.8In_0.2As_0.19Sb_0.81/p₁-Ga_0.9In_0.1As_0.09Sb_0.91 and N₁-GaSb/n₂-Ga_0.9In_0.1As_0.09Sb_0.91/p-Ga_0.8In_0.2As_0.19Sb_0.81 infrared photovoltaic detectors, respectively. The analysis results show that the main absorption appears in the p-type Ga_0.8In_0.2As_0.19Sb_0.81 material with either front- or backside illuminated case for above two structures. In each structure, the carrier concentration obviously affects the detectivity. The carrier concentration in the wide-bandgap material for the isotype heterojunction should be reduced as low as possible to reduce the tunneling rate at the isotype heterointerface. Moreover, the change of the detectivity with the p-side surface recombination velocity for the N₁-n₂-p structure is more sensitive than that with the p₁-side surface recombination velocity for the N-p₂-p₁ structure. In the N-p₂-p₁ structure with the incident light from the p₁-side surface, two-color detection is achieved.     

A PLL clock generator with 5 to 10 MHz of lock range formicroprocessors

A microprocessor clock generator based on an analog phase-locked loop (PLL) is described for deskewing the internal logic control lock to an external system lock. This PLL is fully generated onto a 1.2-million-transistor microprocessor in 0.8-μm CMOS technology without the need for external components. It operates with a lock range from 5 to 110 MHz. The clock skew is less than 0.1 ns, with a peak-to-peak jitter of less than 0.3 ns for a 50-MHz system clock frequency     

Analysis and observation of backscatter-induced crosstalk in a 2-DFDM fiber gyro system

The modulation characteristics of first-order backscatter-induced crosstalk noise in a 2-D frequency-division-multiplexed fiber gyro system are analyzed and experimental results presented. The noise can be reduced from 5°/h to 0.2°/h (0.25 NEB) by proper choice of modulation depth and/or frequency     

镁合金表面喷铝防腐蚀层的微观组织分析

在AZ91D镁合金表面热喷铝，用以提高其表面的耐腐蚀性能。采用SEM，EPMA等方法对AZ91D表面喷铝扩散层的组织进行了仔细的观察与分析，发现在防腐蚀层上有大量的Mg17Al12相存在，且呈决状及非连续片状分布。经显微硬度测定，喷铝层硬度较镁合金基体高；腐蚀后这种相凸出于基体，比镁合金基体有较好的耐腐蚀性能。     

重点建设工程档案管理工作探讨

针对重点建设工程档案的管理现状,提出了明确岗位责任、加强制度建设以及夯实基础工作的档案管理理念。     

A knowledge-based system for sensor selection

This paper presents a Knowledge-based system (KBS) developed to allow users, who may not be knowledgeable about sensors, to select sensors suitable for their specific needs. The KBS runs on a micro-computer. The selection criteria are user specified and are based on the desired measurement parameters. The system output includes all of the operational and dimensional parameters of the recommended sensor, price, and vendor information.     

Analyses of the practical adhesion strengths of the metal/polymer interfaces in electronic packaging

There is a plethora of techniques to measure the adhesion strength of metal/polymer interfaces. However, the practical adhesion strength, which is the work done in separating the film from the substrate (or one film from another), is very sensitive to the test methods and the mechanical effects, such as the residual stress, thickness and mechanical properties of the layers, strain rate, and phase angle. Deriving intrinsic-adhesion properties of the interfaces, which are independent of such parameters, from the practical adhesion-strength measurements is a formidable task. In the present work, data from the three commonly used adhesion tests; pull-out, 90°-peel, and T-peel tests are compared with the intrinsic-adhesion properties of the interface, such as the interface-fracture toughness or the interface-fracture energy, and their implications are discussed. Material systems analyzed were Cu-based lead frame/epoxy-molding compound (EMC) and Cu/Cr/polyimide.     

光纤专用网中基于DSP的Q值在线检测模块的设计

基于误码率与Q值的对应关系，本文介绍一种Q值在线检测方法，模块设计采用DSP技术，并讨论了该模块在光纤工业专用网（FIN）中的应用。     

微重力落塔电磁悬吊、释放技术研究

论述了微重力落塔电磁悬吊、释放、提升机构的关键技术,电磁释放过程的特性分析以及微重力落塔实际试验的情况。分析说明:悬吊、释放性能的好坏决定了试验落舱的微重力水平,也是微重力落塔试验能否成功的关键技术。