Effects of intermetallic compound on the electrical and mechanical properties of friction welded Cu/Al bimetallic joints during annealing

Al/Cu metal joints applied for the electrical connector was joined by the friction welding method to limit the formation of intermetallic compound under optimum friction welding condition. To guarantee the reliability of the Al/Cu joints in service requirement, the effects of the intermetallic compound layer on the electrical and mechanical properties have been investigated under various annealing conditions. Two kinds of intermetallic compounds layer were formed in the joints interface and identified by AlCu and Al₂Cu. The growth kinetic of these intermetallics during the annealing can be followed by volume diffusion process. The activation energy of Al₂Cu, AlCu and total intermetallic compound (AlCu + Al₂Cu) represented 107.5, 98.42 and 110.22 kJ/mol, respectively. A thicker intermetallic compound layers could seriously degrade the electrical resistivity and tensile strength. The electrical resistivity with 21 μm thickness of intermetallic compound was 45 μΩ cm and increased to be 85 μΩ cm with 107 μm of intermetallic compound. Tensile strength remarkably decreased from 85 MPa to near zero at the annealing condition of 773 K and 129.6 ks and fracture occurred through the intermetallic compound layers.     

Effects of CeF3 on properties of self-shielded flux cored wire

0 IntroductionSelf-shielded flux cored wire is a newly developedwelding material used without gas protection. Use of suchcored wires has grown rapidly in developed countriesbecause of the following advantages: simple use, goodwind resistance ability, lower cost resulted from highproductivity and strong desulfurization ability[1]. Self-shielded flux cored wires are preferred for on-site weldingsuch as ship and barge building, storage tank, bridge,offshore oil platform buildings and so on[2 -3].…     

Computer generation of phase diagrams and the associated free energy curves for a binary system

An interactive computer program is introduced in order to make a simultaneous graphical presentation of phase boundaries and their corresponding free energy curves. The program, which uses a graphics display terminal, is a useful tool in teaching thermodynamic concepts involved in phase diagrams, especially for undergraduate students.     

A modified embedded-atom method interatomic potential for the Fe–H system

A modified embedded-atom method (MEAM) interatomic potential for the Fe–H binary system has been developed using previously developed MEAM potentials of Fe and H. The potential parameters were determined by fitting to experimental data on the dilute heat of solution of hydrogen in body-centered cubic (bcc) and face-centered cubic (fcc) Fe, the vacancy–hydrogen binding energy in bcc Fe, and to a first-principles calculation for the lattice parameter and bulk modulus of a hypothetical NaCl-type FeH. The potential accurately reproduces the known physical properties of hydrogen as an interstitial solute element in bcc and fcc Fe. The applicability of the potential to atomistic approaches for investigating interactions between hydrogen atoms and other defects such as vacancies, dislocations and grain boundaries, and also for investigating the effects of hydrogen on various deformation and mechanical behaviors of iron is demonstrated.     

Unsteady extinction mechanism of nonpremixed flame interacting with a vortex

The extinction mechanism of a CH₄/N₂-air counterflow nonpremixed flame interacting with a single vortex was numerically studied. An augmented reduced mechanism was used to treat the CH₄ oxidation reactions. The contribution of each term in the energy and the OH species equations were evaluated to investigate the unsteady extinction mechanism of nonpremixed flame. The flame temperature began to decrease due to the convection heat loss when the flame interacted with a vortex. The investigation of the radical behavior during the flame-vortex interaction process also provided useful information on the unsteady extinction mechanism. The OH radical concentration could be used as a good tracer of the state of the unsteady extinction of nonpremixed flame. The reduction mechanism of OH concentration was confirmed by analyzing the contribution of each term in the OH species equation. At initial stage of flame-vortex interaction, the OH production and consumption rates increased gradually, while the OH concentration was kept nearly constant. Near the extinction limit, the OH production rate decreased rapidly due to the low flame temperature, and the balance between the OH production and OH consumption by diffusion could not be maintained. The unsteady nonpremixed flame interacting with a vortex under the conditions of regime (V) shown in the spectral combustion diagram [Thévenin, D., Renard, P.H., Fiechtner, G.J., Gord, J.R., Rolon, J.C., 2000. Regimes of non-premixed flame-vortex interactions. Proceedings of the Combustion Institute 28, 2101-2108.] was finally extinguished due to low reactivity, which was induced by the low flame temperature.     

气相色谱法测定有机化合物的蒸发热

本文用气相色谱测定了多种烷烃、芳烃、醇类和酯类的蒸发热。结果表明,测定数据与文献数据基本一致,误差一般在±5%以内。是一种简单、快捷的测定方法。     

不同活化剂对石油焦基活性炭孔结构的影响

以石油焦为原料 ,Na OH,KOH和 Na2 CO3 为活化剂制备活性炭 ,采用氮气吸附考察了不同活化剂对活性炭的比表面积、中孔和微孔孔径分布、孔容积及平均孔径等孔结构的影响 .结果表明 :KOH活化制备的活性炭包含 1 nm的微孔和 4nm的中孔 ,总孔容 0 .648cm3 /g,比表面积大 ;Na OH制备的活性炭以 1 nm的微孔为主 ,占总孔容 ( 0 .1 65 cm3 /g)的 98% ,平均孔径 1 .83nm;Na2 CO3 制备的活性炭以 4nm的中孔为主 ,占总孔容 ( 0 .1 43cm3 /g)的 68.5 % ,平均孔径 3.42 nm,比表面积小 .3种样品的孔径都呈现出多峰分布特征 .KOH和 Na2 CO3 活化制备的活性炭的 N2 吸附脱附曲线属于 型 ,Na OH活化制备的活性炭吸附脱附曲线属于 型 .     

Thermal analysis of polymer–water interactions and their relation to gas hydrate inhibition

Gas hydrates formed in oil production pipelines are crystalline solids where hydrocarbon gas molecules such as methane, propane, and their mixtures are trapped in a cagelike structure by hydrogen‐bonded water molecules to form undesirable plugs. Methanol and glycol are currently used to prevent these plugs via thermodynamic inhibition. Small amounts of water‐soluble polymers may provide an alternate approach for preventing gas hydrates. In this study, we expand the fundamental understanding of water–polymer systems with differential scanning calorimetry. Nonfreezable bound water was used to quantify polymer–water interactions and relate them to the chemical structure for a series of polymers, including acrylamides, cyclic lactams, and n‐vinyl amides. For good interactions, the water structure needs to be stabilized through hydrophobic interactions. An increased hydrophobicity of the pendant group also appears to favor polymer performance as a gas hydrate inhibitor. Good inhibitors, such as poly(diethyl acrylamide) and poly(N‐vinyl caprolactam), also show higher heat capacities, which indicate higher hydrophobicity, than poor performers such as polyzwitterions, in which hydrophilicity dominated. The phase behavior and thermodynamic properties of dilute polymer solutions were also evaluated through measurements of the heat of demixing and lower critical solution temperature. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 103: 2642–2653, 2007     

五种化合物临界温度和临界压力的测定

The critical properties of five compounds,including propanal,butanal,1-pentanal,2-methel butanal and trimer of ethanal,were determined for the first time by a new capillary quick-flow method. The apparatus was improved with a capillary tube and checked with hexane and 1-heptene as standard reagents. The experimental results proved that the determination of critical properties by quick-flow method with a capillary tube apparatus was successful.     

Tensile mechanical properties of sulfonated poly(ether ether ketone) (SPEEK) and BPO4/SPEEK membranes

A study to evaluate the tensile mechanical properties of sulfonated poly(ether ether ketone) (SPEEK) and BPO₄/SPEEK composite membranes has been carried out. It is aimed to give an assessment of these materials for applications in proton exchange membrane fuel cells. The stress–strain response of the membranes was measured as a function of the degree of sulfonation (DS) and the filler–matrix ratio. In addition, the effects of immersion in water at various temperatures were explored in situ by means of a homemade testing chamber fitted to the tensile analyzer. The results indicate that the DS has an important influence on the final mechanical behavior of the membranes. The introduction of the BPO₄ solid filler leads to deterioration in mechanical performance compared to unfilled SPEEK. A general picture of the microstructural features influencing the mechanical properties of SPEEK and BPO₄/SPEEK membranes is proposed. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 98: 2380–2393, 2005