Enhanced utilization bound of Rate-Monotonic scheduling in Controller Area Networks

When priorities to message streams are assigned using Rate Monotonic (RM) for a Controller Area Network (CAN), the utilization bound is known to be about 25% for CAN 2.0A and 29% for CAN 2.0B. In this letter, we present a higher utilization bound than the existing ones with a reasonable constraint. The new utilization bounds are approximately 34% for CAN 2.0A and 41% for CAN 2.0B if no single message stream's utilization exceeds 46% or 27% of the total utilization for CAN 2.0A or CAN 2.0B, respectively.     

A survey of traffic-based routing metrics in family of expected transmission count for self-organizing networks

Self-Organizing Networks (SONs) are attractive for applications where flexibility, resilience, and a large network service area are required. In order to meet the requirements of those applications, the principal issue is to guarantee efficient routing in SONs. Hence, the design and selection of appropriate routing metrics is important. A mass of metrics have been proposed in the past several decades. Among all the metrics, Expected Transmission Count (ETX) has drawn the most attention. Since the proposal of ETX, many ETX-based or extended metrics have been proposed. ETX and its descendants compose the ETX family. This paper is an attempt to analyze, compare and summarize traffic-based routing metrics in the ETX family. Details of each routing metric are presented and analyzed. Some of our viewpoints on the principal for designing metrics in SONs are presented.     

Semi-annual cycle of sea-surface temperature in the East/Japan Sea and cooling process

Semi-annual cycles of the sea-surface temperature (SST) in the East/Japan Sea (EJS) and their forcings were examined by analysing National Oceanic and Atmospheric Administration/Advanced Very-High-Resolution Radiometer data, scatterometer wind vectors, and heat flux data. The semi-annual cycle contributed to the total variance of the SST by 8% and amounted to 25% of the amplitudes of the annual SST cycle, particularly in the Tatarskiy Strait and along the continental shelf off Russia. The lowest phase, corresponding to the minimum SST, occurred during early November and 6 months earlier in May or June depending on the position. The forcings of the semi-annual cycle were not semi-annual but substantially annual with a lag of 6 months, which gave rise to SST cooling in spring and autumn. Our analyses illustrated that SST cooling in autumn was caused by direct, local atmospheric wind forcings, whereas the cooling with large amplitudes of the semi-annual cycle in spring was caused by the non-local, remotely forced cold water advection of the Liman Current associated with sea-ice melting in the Tatarskiy Strait. The phase lag of 1–2 months between the complete melting of the sea ice in the Tatarskiy Strait and the surface cooling along the Russian continental shelf was related to the advection of cold water from sea ice in the form of the Liman Cold Current. The semi-annual cycle also resulted from asymmetry of the time series of the SST due to a long cold winter and a short warm summer. To understand how SST curves are distorted and asymmetric, we suggested two mathematical parameters of kurtosis and skewness. In addition, we suggest that the ratio of the semi-annual amplitude to the annual amplitude of SST harmonics can be used as a typical indicator of the asymmetry in year-to-year SST variations.     

Typhoon eye extraction with an automatic SAR image segmentation method

Spaceborne microwave synthetic aperture radar (SAR), with its high spatial resolution (10–100 m), large area coverage, and day/night imaging capability, has been used as an important tool for typhoon monitoring. Since the microwave signal can penetrate through clouds, SAR images reveal typhoon morphology at the sea surface. Within the region of a typhoon eye, wind speed and the associated sea surface roughness are usually low. Therefore, the typhoon eye can be well distinguished as dark areas in SAR images. However, automatic typhoon eye extraction from SAR images is hampered by SAR image speckle noise and other false-alarm dark features contained in an image. In this study, we propose an image processing approach to extract typhoon eyes from SAR images. The three-step image processing includes: (1) applying an extended non-local means image denoizing algorithm to reduce image speckle noise; (2) applying a top-hat transform to denoized imagery to enhance the contrast; and (3) using a labelled watershed to segment the typhoon eye. Experimental results from analysing three Environmental Satellite SAR typhoon images show that our approach provides fast and efficient SAR image segmentation for typhoon eye extraction. Typhoon eyes are segmented correctly, and their edges are well detected. Our experimental results are comparable to manually extracted typhoon eye information. Fine-tuning of this approach will provide an automatic tool for typhoon eye information extraction from SAR images.     

Sintering Behavior of Cadmium-Doped Pb(Ni1/3Nb2/3)O3–PbZrO3–PbTiO3 Ceramics

Substituting Cd²⁺ ions into the A and B sites in a Pb(Ni_1/3Nb_2/3)O₃PbZrO₃PbTiO₃ (PNNPZPT) ternary perovskite material made it possible to determine the effects of the Cd²⁺ ion substitution site on sintering behavior. The substitution site of the Cd²⁺ ion was identified by using X-ray photoelectron spectroscopy spectra. Although Cd²⁺ ions were substituted into the A and B sites in PNNPZPT, the Cd²⁺ ions preferred the A site over the B site. When Cd²⁺ ions replaced Pb²⁺ ions, a weight gain was observed during sintering. On the other hand, replacing Ni2 ions with Cd²⁺ ions promoted weight loss. Those weight changes indicated that Cd²⁺ ions change the bonding strength between the B-site cations and the oxygen of the octahedron in a perovskite structure. Density was influenced by the Cd²⁺ ion substitution site, and the A-site-doped compositions had higher densities than the B-site-doped compositions.     

Prelaunch calibration and primary results from in-orbit calibration of the atmospheric correction microwave radiometer (ACMR) on the HY-2A satellite of China

The atmospheric correction microwave radiometer (ACMR) is one of the main payloads for correcting atmospheric path delay in the radar altimeter on the Haiyang-2A (HY-2A) satellite. The ACMR is a three-band microwave radiometer operating at 18.7, 23.8, and 37.0 GHz. Calibration of the ACMR is important for applying its measurements to correct for atmospheric effects on the HY-2A altimeter signal transmission in the air. Therefore, a detailed introduction to the principles and specifications of the ACMR system is given first. The thermal vacuum calibration method of the ACMR is discussed and analysed, and the microwave transfer functions and related coefficients are given, especially the nonlinear coefficients derived from a test for correcting nonlinear responses between the input of antenna temperature and the output of voltage at each channel of the ACMR. Furthermore, antenna pattern correction algorithms for removing the effects of side lobe and cross-polarization are derived and their coefficients are used for in-orbit data processing. Primary calibration results are given by comparing with the similar spaceborne Jason microwave radiometer (JMR) on the Jason-1 satellite and with the advanced microwave radiometer (AMR) on Jason-2. The results of this comparison show that the data from the ACMR match well to those from the JMR and AMR.     

Effect of reactive diluents on properties of unsaturated polyester/montmorillonite nanocomposites

Unsaturated polyester (UP)/montmorillonite (MMT) nanocomposite was prepared by using hydroxypropylacrylate (HPA) as a reactive diluent instead of conventional styrene monomer and the effect of polarity of reactive diluent on properties of nanocomposite was investigated. X‐ray and mechanical test data indicated that mixing for an extended period of time is essential to enhance the physical properties of nanocomposites in the UP/Cloisite 6A system. This was attributed to the high polarity of HPA that may disturb the preintercalation of UP resin into the galleries of MMT. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 92: 238–242, 2004     

组织工程多孔支架制备技术进展

综述了天然或合成生物降解材料为原料的组织工程多孔支架的几种制备方法，包括无纺织物／纤维粘结法、溶液浇铸／粒子洗出法、相分离／冻干法、气体成孔法和三维“印刷”等方法。特别评述了近期组织工程多孔支架研究进展及其在骨、软骨和皮肤等组织修复中的应用。     

A randomized algorithm for natural object colorization

Natural objects often contain vivid color distribution with wide variety of colors. Conventional colorization techniques, on the other hand, produce colors that are relatively flat with little color variation. In this paper, we introduce a randomized algorithm which considers not only the value of target color but also the distribution of target color. In essence, our algorithm paints a color distribution to a region which synthesizes color distribution of a natural object. Our approach models the correlation between intensity and color in HSV color space in terms of H – S, H – V and S – V joint histogram. During the colorization process, we randomly swap and reassign color of a pixel to minimize a cost function that measures color consistency to its neighborhood and intensity‐to‐color correlation captured in the joint histogram. We tested our algorithm extensively on many natural objects and our user study confirms that our results are more vivid and natural compared to results from previous techniques.     

The use of non–physical standards in colour communication and matching

As a result of developments in spectrophotometry, together with improved accuracy in computer colour matching and laboratory dyeing, non–physical standards (reflectance data) can now be used for the successful communication, matching and quality control of colour. In colour palette generation, ‘matching by numbers’ has become a reality.