Synthesis and characterization of novel aromatic condensation polymers containing rigid benzoxazole pendent groups

A new aromatic diamine monomer containing benzoxazole substituents was prepared by a multistep synthesis starting from 1,4‐dibromo‐2,5‐difluorobenzene. The diamine was polymerized with commercial aromatic dianhydride or dicarboxylic acid chloride monomers to provide several different poly(amic acid)s and polyamides with their inherent viscosities in the range of 0.24–0.46 dL/g. Thermal properties of these polymers including thermal imidization of poly(amic acid)s into polyimides were investigated by using FTIR, DSC, and TGA. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 92: 178–185, 2004     

单螺杆挤出过程的数值模拟

以三段七区物理模型为基础，采用面向对象程序设计语言VisualC ，对整个单螺杆挤出过程进行了数值模拟。所得压力。温度等工艺参数的模拟结果与实验值吻合较好，说明采用数学模型的正确性和数值算法的可行性。     

纳米层状双金属氢氧化物的制备及结构表征

采用恒定pH 12±0.2,按n(Mg2+)∶n(Al3+)∶n(OH-)∶n(CO2-3)=6∶2∶16∶1配制溶液,采用一步反应液相法,制备纳米层状双金属氢氧化物(LDH)粉体.为了获得无团聚、分散均匀的纳米粉体,探讨了溶剂置换干燥、真空干燥、常压干燥对纳米LDH粉体形成团聚的影响;用X射线衍射仪、透射电镜、红外光谱仪和元素分析仪对样品的物相、形貌、粒径和组成进行了表征.结果表明,溶剂置换干燥能够有效防止纳米粉体形成硬团聚,样品分散性好,呈针状形态,长50 nm,宽5 nm.     

硝酸钠卤水沸点变化理论计算

根椐已有的文献与数据,采用数学模型方法,研究了硝酸钠卤水沸点在不同组成、不同压力条件下的变化关系,确定了硝酸钠卤水沸点与质量分数及压力的数学方程式;根椐硝酸钠卤水压力与组成,可以计算出硝酸钠卤水的沸点值,为新疆都善县库木塔格硝酸钠矿大规模生产硝酸钠提供了重要设计依据.     

工业过程的先进控制

在分析工业过程特点的基础上，总结了工业过程先进控制的发展现状，阐述了PID控制器参数整定和模型预测控制的基本概念和内容，讨论了工业过程先进控制的核心内容及其带来的可观的经济效益，并探讨了先进控制软件的产业化问题。     

Study of stability of high‐temperature polyimides using TG/MS technique

The oxidative stability of the carbon fiber‐reinforced composite of polyimide was examined, in real time, using the evolved gas analysis techniques. Off‐gas degradation products suggested the onset temperature for chain scissions to be fairly low at about 190–220°C. Based on the off‐gas products present and the trend of their release, the composite degradation mechanism appeared to be similar between 190 and 371°C, thereby marking 371°C to be the highest accelerated aging temperature for its long‐term lifetime prediction. Beyond 371°C, different degradation mechanisms would apply. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 83: 1219–1227, 2002     

Elucidation of the miniemulsion stabilization mechanism and polymerization kinetics

Styrene/hexadecane miniemulsions were polymerized at 50°C using a redox initiator. The miniemulsions and their corresponding latexes were characterized in terms of size, polymerization rate, and surface properties. The resulting data were analyzed to elucidate the miniemulsion stabilization and polymerization mechanisms. It was found that the free surfactant concentration exceeded the critical micelle concentration when large amounts of surfactant (60 mM sodium lauryl sulfate) were used, resulting in simultaneous micellar and droplet nucleation. Most surfactant was on the surface of the droplets (85%) or particles (95%). The fractional surface coverage was proportional to the surfactant concentration to the 0.55 power. Using a particle diameter equation, the number of particles was calculated to be proportional to the surfactant concentration to the 1.35 power. Through direct particle size measurements, a power of 1.38 was confirmed. The rate of polymerization was determined by reaction calorimetry to be proportional to the number of particles to the 0.59 power, in contrast to classical Smith–Ewart kinetics for conventional emulsions (1.0 power). The average number of radicals per particle was estimated from the rate and number data, and varied with the particle diameter to the 0.97 power. The observed kinetic dependencies were validated through an extension of Smith–Ewart theory. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 90: 3987–3993, 2003     

Effect of solution properties on nanofibrous structure of electrospun poly(lactic‐co‐glycolic acid)

Electrospinning of poly(lactic‐co‐glycolic acid) (PLGA) in chloroform or 1,1,1,3,3,3‐hexafluoro‐2‐propanol (HFIP) was investigated, focusing on its solution parameters, to develop nonwoven biodegradable nanofibrous structures for tissue engineering. PLGA nanofibers were obtained by electrospinning of 15 wt % PLGA solution and the resulting average fiber diameters were varied with the range of 270–760 nm, depending on solution property. When small amounts of benzyl triethylammonium chloride (BTEAC) was added to the PLGA/chloroform solution, the average diameter was decreased from 760 to 450 nm and the fibers were densely amounted in a straight shape. In addition, the average fiber diameter (270 nm) of nanofibers electrospun from polar HFIP solvent was much smaller than that (760 nm) of nanofibers electrospun from nonpolar chloroform solvent. Therefore, it could be concluded that conductivity or dielectric constant of the PLGA solution was a major parameter affecting the morphology and diameter of the electrospun PLGA fibers. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 99: 1214–1221, 2006     

煤制氨装置氨合成塔技术改造及性能考核

介绍天脊集团TopsφeS-100型氨合成塔改造为Casale300氨合成塔后，催化剂的装填，还原，工况优化和72小时考核，考核表明，各项指标均优于合同值，改造获得成功。