乳胶制品生产的工序能力分析及质量控制

本文分析了乳胶制品的生产过程，并对工序能力指数进行了分析，从而推断出产品的质量。     

读者决策采购（PDA）成功实施的关键性因素分析

读者决策采购作为一种全新的基于读者需求的资源建设模式,目前国内还没有高校图书馆实施。介绍了读者决策采购面临的问题,提出PDA要在我国高校图书馆成功实施,需制定严格的标准、选择合适书商并及时进行跟踪与评价。     

Engineering all-aromatic polyamide surface from hydrophilic to superhydrophobic and the accelerated strategy

Being a new kind of nanomaterials, aromatic polyamide nanofibers (ANF) have been much highlighted in recent studies. We here demonstrate an isopropyl alcohol (IPA) accelerated chemical cleavage on poly (p-phenylene terephthalamide) chopped fibers, which provides an efficient preparation method of ANF. The comprehensive study on the processes accelerated by different alcohols revealed that the preparation time of ANF in the mixed medium of dimethyl sulfoxide (DMSO)-alcohol (20:1 in volume) was shorten to 45 min and 75 min for methanol (ethanol) and isopropanol, respectively. However, the nanofibers prepared in DMSO-IPA exhibited the minimum in axial and radial dimensions, providing the finest and most uniform diameter of 16 nm. The corresponding ANF films through vacuum assisted filtration also showed the highest tensile strength of 150 MPa, in comparison with those of the ANF films prepared using other alcohols, which were about 110 MPa. Furthermore, ANF/silicon hybrid films were prepared by the ionic ring-opening reaction followed by the alkoxysilane condensation and nanoparticle fabrication. By changing the organo functional groups in the alkoxysilane, the surface of the films were adjustable in a wide contact angle range from 56° (hydrophilic) to 150° (superhydrophobic), suggesting the amendable interfacial properties potential applicable to composite fabrication with most of the resin matrix.     

EFFECT OF SILICON ON THE TRANSITION OF BRITTLENESS IN A NICKEL BASE WROUGHT SUPERALLOY

Ni-15Cr-6W-3Mo-2Al-2Ti变形高温合金的室温抗张强度、塑性和冲击性能,随着合金中Si含量的变化呈现马鞍型的变化,即在0.4—0.6％Si范围内出现一个低塑性、低拉伸强度和低冲击韧性区。造成这种现象的本质原因是由于Si含量变化改变了晶界碳化物沉淀析出顺序、析出类型、析出量和析出形态。该合金晶界碳化物析出可分为四个阶段:第一阶段,<0.1％Si时,只有单一的M_(23)C_6析出;第二阶段,>0.1％Si以后,除M_(23)C_6外,M_6C开始析出,一直到0.4％Si时增加2缓慢;第三阶段,0.4—0.6％Si时,M_6C大量析出逐渐取代M_(23)C_6;第四阶段,>0.6％Si以后,M_6C量占绝对优势,但增加幅度比第三阶段小得多。从晶界形态来看,第一、二、四阶段皆属不连续的链状形式,只有第三阶段晶界呈现连续膜状。因此,造成性能下降的原因不是因为析出M_6C,而是它的形态,当它以颗粒状分布在晶界上时是一个很好的强化相。第三阶段的不正常析出是性能下降的本质因素。本研究结果打破了只要镍基合金中MO+1/2>W>6％(重量百分比)就形成M_6C的经验判据,“Si”才是该合金碳化物沉淀析出过程的控制因素。本文还对比了冶炼工艺差别对碳化物析出过程的影响。     

简单断面孔型计算机绘图系统简介

介绍了简单断面孔型计算机绘图系统的编制方法、使用范围 ,计算机绘图的步骤及特点     

基于MATLAB的热定型机PID张力控制器设计

文章介绍了热定型机的工作原理,及其定型过程中张力系统控制结构图,并以此为基础建立了张力控制系统的数学模型.基于比例积分微分(PID)控制器的原理,利用MATLAB软件设计了张力控制器,其编写的PID参数整定函数能作为MATLAB函数进行直接调用.实验和仿真结果表明:该控制器完全满足张力控制系统的性能要求,降低了超调量,提高了系统的动静态性能;同时设计简单、易于实现.     

多目标优化理论在蜂窝夹芯结构设计中的应用

在确定了设计变量及目标函数的基础上,根据结构本身的要求,推导出用于多目标优化的5个约束条件.根据多目标优化理论,采用乘除法对蜂窝夹芯结构进行了评价函数的构造,并用VC语言编制了钢质蜂窝夹芯减振板结构的优化程序,该程序可实现结构尺寸及性能的优化,并计算出各目标函数的最终值.     

激光快速成形Rene′88DT高温合金的时效强化研究

研究了时效时间对激光快速成形后时效硬化镍基高温合金Rene′88DT中沉淀相组织演化和力学性能的影响。发现随时效时间的增加，沉淀相y’略有长大，颗粒之间发生大颗粒吞噬小颗粒的粗化，时效40h后沉淀相颗粒粗化明显。对经不同时间时效后的激光快速成形Rene′88DT试样进行了硬度测试。结果显示，在时效时间为28h时，硬度有一峰值HRC49。在此基础上，采用1165℃，2h固溶、空冷＋760℃，28h时效的热处理工艺对激光快速成形标准拉伸棒样进行了热处理，拉伸结果显示成形件的抗拉强度较激光沉积态提高了400MPa，屈服强度接近同种材料的粉末锻造水平。     

Camouflage texture evaluation using a saliency map

Multimedia Systems - Camouflage effect evaluation and examination is an important procedure in digital camouflage pattern design as it is helpful in improving the objectivity and effectiveness...