反向工程中测量点云配准的新方法

在光学非接触三维测量中，复杂对象的重构需要多组测量数据的配准。为了获得好的配准结果，提出一种新的配准方法——直接误差分析配准方法。该方法基于一种新型的双目CCD光栅投影测量系统进行测量和分析。实验结果表明该测量方法的配准误差大约0．2mm左右．从而证实该方法的可行性。     

钻杆环缝数控自动焊机

研制的钻杆环缝数控自动机焊为全自动的数控焊机。用于钻杆与两端法兰的内外共4条环缝的焊接。工件的上料、定位、夹紧、内外焊枪的到位、内外焊枪的焊接、自动排列焊道各层各道的焊接工艺参数的改变等均能自动进行。不同管径和不同壁厚采用的各种焊接参数都可在人机界面上预置。采用富氩混合气体保护焊工艺方法，焊缝美观，性能优良，几乎没有飞溅。经大量的生产实践证明该钻杆环缝数控自动焊机焊接质量好，生产效率高。     

MODELLING OF P/M FORMING PROCESSES BY FEM

ＭＯＤＥＬＬＩＮＧＯＦＰ／ＭＦＯＲＭＩＮＧＰＲＯＣＥＳＳＥＳＢＹＦＥＭ￥Ｗｅｉ，Ｙｕａｎｐｉｎｇ；Ｒｕａｎ，Ｘｕｅｙｕ（ＤｅｐａｒｔｍｅｎｔｏｆＰｌａｓｔｉｃｉｔｙＴｅｃｈｎｏｌｏｇｙ，ＳｈａｎｇｈａｉＪｉａｏＴｏｎｇＵｎｉｖｅｒｓｉｔｙ，Ｓｈａｎｇ...     

基于特征模板的分组编程法

介绍了国内数控加工中存在的问题，结合广东省科委项目，提出了基于平面、曲面特征模板的分组加工编程法，并用实例验证了这种方法的正确性，极大地提高UG软件的加工编程效率，也解决了加工编程难以掌握的问题。     

正向充液变薄拉深工艺的研究

提出了一种称为正向充液变薄拉深的工艺方法。从理论上推导出变薄成形传力区拉应力计算式，并采用软铝车削毛坯进行了正向充液变薄拉深试验。当液压达到了１２０ＭＰａ时，车削铝毛坯的极限变薄拉深系数由０．５减小到０．３，说明正向充液变薄拉深工艺能有效地提高一次变薄拉深成形极限。     

Microstructures of mechanically activated Ti-46at.% Al powders and spark plasma sintered ultrafine TiAl alloy

Powder of Ti-46at.%Al was synthesized through mechanical activation (MA) for different milling times, and the 16 h MAed powder was sintered by using a spark plasma sintering (SPS) process at different sintering temperatures. The XRD profiles showed that the MAed Ti-46at%Al powder for 12,16, and 20 h contained initial α-Ti and Al phases, and that the SPSed TiAl alloys contained the gamma TiAl and α2-Ti3Al phases. The TEM showed two different types of regions in the 16 h MAed Ti-46at.%Al powder. One type consisted of only Al with a grain size about 80 nm, and the other type a mixture of Al and Ti with a grain size of 30 nm. According to the optical micrographs of MA-SPSed samples, the alloys sintered at higher temperatures showed a coarser microstructure. In the case of the 1473 K sintering, typical duplex structures ((α2 + γ) lamella and γ phases) with interlamellar spacings of 50-400 nm and the grain size either less man 100 nm, or 1000 nm were observed.     

弯曲回弹逆解公式及其在焊管预弯机组设计中的应用

根据小曲率弯曲成形的特点，考虑了板料弯曲的纯弹性变形部分对回弹的影响，推导出根据板料强度、厚度和最终成形半径直接计算弯曲半径的回弹逆解公式，并应用于大口径UOE焊管预弯成形的设计上。根据计算公式给出了B-X100钢级板料UOE焊管预弯成形的预弯辊半径优化设计诺谟图。     

结晶助剂对晶种分解的影响研究

本文研究了结晶助剂对晶种分解过程的影响 ,认为加入适量的结晶助剂对焙烧产品氧化铝的白度几乎没有影响、对分解率的影响不大 ,可以提高产品的粒度。     

FRACTAL ANALYSES OF DIRECTIONAL SOLIDIFICATION BEHAVIOR OF A Ni-BASE SUPERALLOY

The morphology of solid/liquid interface of a directionally solidification process is describedby means of fractal analysis,and the relations among the fractal dimension of the solid/liq-uid interface,solidification rate,dendrite arm space and the phosphorus content of the test al-loys have been given.It was found that the increase of the solidification rate and the phos-phorus content of the test alloy will lead to a increase,following the regularity of exponentialfunction,in the fractal dimension of solid/liquid interface.Furthermore,by combining thefractal theory and the thermodynamic principle with the measured results,it has been provedthat the fractal dimension is not only a kind of simple geometrical parameter used in des-cribing irregular geometry,but also a state function depending the change of solidificationparameters and chemical compositions.     

板料成形数值模拟的关键技术及难点

本文结合国内外板料成形数值模拟的最新研究动态，从关键算法、屈服函数、本构方程、有限元列式、接触问题、破裂准则、回弹计算、起皱分析八个方面叙述了板料成形有限元计算的关键技术及主要难点。