Behavior of cellulose-degrading bacteria in thermophilic anaerobic digestion process.

Previously, we found that the newly isolated Clostridium sp. strain JC3 became the dominant cellulose-degrading bacterium in thermophilic methanogenic sludge. In the present study, the behavior of strain JC3 in the thermophilic anaerobic digestion process was investigated quantitatively by molecular biological techniques. A cellulose-degrading experiment was conducted at 55 degrees C with a 9.5 L of anaerobic baffled reactor having three compartments (Nos. 1, 2, 3). Over 80% of the COD input was converted into methane when 2.5 kgCOD m(-3) d(-1) was loaded for an HRT of 27 days. A FISH probe specific for strain JC3 was applied to sludge samples harvested from the baffled reactor. Consequently, the ratio of JC3 cells to DAPI-stained cells increased from below 0.5% (undetectable) to 9.4% (compartment 1), 13.1% (compartment 2) and 21.6% (compartment 3) at day 84 (2.5 kgCOD m(-3)d(-1)). The strain JC3 cell numbers determined by FISH correlated closely with the cellulose-degrading methanogenic activities of retained sludge. A specific primer set targeting the cellulase gene (cellobiohydrolaseA: cbhA) of strain JC3 was designed and applied to digested sludge for treating solid waste such as coffee grounds, wastepaper, garbage, cellulose and so on. The strain JC3 cell numbers determined by quantitative PCR correlated closely with the cellulose-sludge loading of the thermophilic digester. Strain JC3 is thus important in the anaerobic hydrolysis of cellulose in thermophilic anaerobic digestion processes.     

升温下钢构件的强度设计标准

通过与非线性有限元模拟比较,对结构钢构件在升温下的设计公式进行了评估。比较美国钢协与欧洲标准委员会对温度在800℃侧向无支撑的Ⅰ型柱、梁、柱-梁的设计规定。欧洲规范3的规定与有限元模拟的结果相差10%～20%。另一方面,美国钢协的规范预测的强度与模拟结果相差高达2倍。对于温度超过300℃的中细构件,相差最大。提出了对美国钢协规范计算公式的修正建议,修正后的精度与模拟的结果误差在20%～30%。最后讨论了结构防火工程基于构件评估的局限性、未来的研究以及发展方向。     

Radiation grafting of α,β,β-trifluorostyrene onto poly(ethylene-tetrafluoroethylene) film by preirradiation method. II. Properties of cation-exchange membrane obtained by sulfonation and hydrolysis of the grafted film

A Study was made on certain properties of the cation-exchange membranes obtained by the preirradiation grafting of α,β,β-trifluorostyrene (TFS) noto poly(ethylene-tetrafluoroethylene) (ETFE), followed by sulfonation and hydrolysis of the grafted film. Swelling, water uptake, electric conductivity, and transport number of the membranes were measured as a function of ino-exchange capacity. Thermal and chemical stability were also investigated. These properties were found to be mainly dependent on ion-exchange capacity. The stable membrane properties were established due to a homogeneous ion-exchange group distribution in the membrane, as confirmed by x-ray imcroscopy analysis of the membrane cross sections. In addition, the membranes showed good electrochemical, thermal, and chemical properties, and were found to be scceptable for practical use as cation-exchange membranes.     

砂土地基地震液化沉降的两种简易计算方法的对比分析

利用两种简易方法对日本某核电站的砂性土地基在地震液化后的大变形沉降进行了计算和对比分析。这两种简易的实用方法只需要利用标准贯入试验数据就可以操作。计算结果表明,该核电站的砂性土地基在L2级地震作用下会发生较大的地面沉降,并可能对地下管线造成损坏。由于两种方法的计算原理相同,因此计算所得到的地基分层沉降趋势基本一致,但是在数值上存在着较大的差异,这主要是由于两种方法建立的基础试验数据不同以及具体计算方法上存在着差异所造成的。     

Plasma polymerized membranes and gas permeability. II

Thin films were deposited onto porous substrates by plasma polymerization using three kinds of organosilicic compounds, tetramethylsilane (TMS), hexamethyldisiloxane (M₂), and octamethylcyclotetrasiloxane (D₄). Those composite membranes showed different characteristics of gas permeability. When D₄ was plasma-deposited onto a porous substrate, the composites membrane showed the highest oxygen permeability and the lowest oxygen-to-nitrogen permeability ratio. The composite membrane prepared from TMS showed the permeability characteristics opposite to the membrane obtained from D₄. Infrared spectrum of the polymer from D₄ resembles that of dimethylpolysiloxane. The plasma polymers from TMS and M₂ showed different profiles in Si? O absorption bands in the range 1100–1000 cm^-1 or in absorption bands of SiCH₃ groups in the range 850–750 cm^-1 from respective monomers. X-ray photoelectron spectroscopic observation indicated that all the plasma polymers contained more than two species of Si atom with different oxidation states. The greater part of Si atoms in plasma polymers took the same oxidation states in corresponding monomer. The gas permeability characteristics were closely related to the oxidation states of Si atom in the plasma polymers.     

High density packaging technology ultra thin package & new tab package

As electronic devices become more highly integrated, the demand for small, high pin count packages has been increasing. We have developed two new types of IC packages in response to this demand. One is an ultra thin small outline package (TSOP) which has been reduced in size from the standard SOP and the other, which uses Tape Automated Bonding (TAB) technology, is a super thin, high pin count TAB in cap (T.I.C.) package. In this paper, we present these packages and their features along with the technologies used to improve package reliability and TAB. Thin packages are vulnerable to high humidity exposure, especially after heat shock.1 The following items were therefore investigated in order to improve humidity resistance: (1) The molding compound thermal stress, (2) Water absorption into the molding compound and its effect on package cracking during solder dipping, (3) Chip attach pad area and its affect on package cracking, (4) Adhesion between molding resin and chip attach pad and its affect on humidity resistance. With the improvements made as a result of these investigations, the reliability of the new thin packages is similar to that of the standard thicker plastic packages.     

POROSITY AND RESIDUAL EQUILIBRIUM SATURATION OF SINTERED SPHERES OF GLASS BEADS

Sintered spheres(made of glass beads) were simply produced with a definite diameter, with a precision of ±0·5 mm in diameter, for a wide range of sintered angles (0-27°). The experimental values of the porosity of the sintered spheres were consistent with the calculated results for the coordination number N ≠ 8. The residual equilibrium saturation, as one of the basic physical properties of sintered glass beads was investigated experimentally and theoretically, resulting in the presence of a distribution in the angle of pendular ring.     

Radiation grafting of α,β,β-trifluorostyrene onto poly(ethylene–tetrafluoroethylene) film by preirradiation method. I. Effects of preirradiation dose,monomer concentration,reaction temperature,and film thickness

Preirradiation grafting of α,β,β-trifluorostyrene onto poly(ethylene–tetrafluoroethylene) film was studied. The trapped radicals formed upon irradiation were able to induce graft polymerization under appropriate conditions. The influences of the grafting conditions were analyzed kinetically. The grafting rate dependency on the preirradiation dose was found to be of order 0.3, and the monomer concentrations, 1.0. The overall activation energies for this grafting were calculated to be 6.2 × 10⁴ and 9.3 × 10³ J/mol below and above 50°C. The grafting rate was found to be independent of the film thickness, which ranged from 25 to 100 μm.     

Sphinganine‐Like Biogenesis of (E)‐1‐Nitropentadec‐1‐ene in Termite Soldiers of the Genus Prorhinotermes

In 1974, (E)‐1‐nitropentadec‐1‐ene, a strong lipophilic contact poison of soldiers of the termite genus Prorhinotermes, was the first‐described insect‐produced nitro compound. However, its biosynthesis remained unknown. In the present study, we tested the hypothesis that (E)‐1‐nitropentadec‐1‐ene biosynthesis originates with condensation of amino acids with tetradecanoic acid. By using in vivo experiments with radiolabeled and deuterium‐labeled putative precursors, we show that (E)‐1‐nitropentadec‐1‐ene is synthesized by the soldiers from glycine or L ‐serine and tetradecanoic acid. We propose and discuss three possible biosynthetic pathways.