澳大利亚威维霍抽水蓄能电站

威维霍抽水蓄能电站对昆士兰电网及其业主塔朗能源公司起着重要作用。     

Deformation behavior of HCP Ti-Al alloy single crystals

Single crystals of Ti-Al alloys containing 1.4, 2.9, 5, and 6.6 pct Al (by weight) were oriented for 〈a〉 slip on either basal or prism planes or loaded parallel along the c-axis to enforce a nonbasal deformation mode. Most of the tests were conducted in compression and at temperatures between 77 and 1000 K. Trace analysis of prepolished surfaces enabled identification of the twin or slip systems primarily responsible for deformation. Increasing the deformation temperature, Al content, or both, acted to inhibit secondary twin and slip systems, thereby increasing the tendency toward strain accommodation by a single slip system having the highest resolved stress. In the crystals oriented for basal slip, transitions from twinning to multiple slip and, finally, to basal slip occurred with increasing temperature in the lower-Al-content alloys, whereas for Ti-6.6 pct Al, only basal slip was observed at all temperatures tested. A comparison of the critically resolved shear stress (CRSS) values for basal and prism slip as a function of Al content shows that prism slip is favored at room temperature in pure Ti, but the stress to activate these two systems becomes essentially equal in the Ti-6.6 pct Al crystals over a wide range of temperatures. Compression tests on crystals oriented so that the load was applied parallel to the c-axis showed extensive twinning in lower Al concentrations and 〈c+a〉 slip at higher Al concentrations, with a mixture of 〈c+a〉 slip and twinning at intermediate compositions. A few tests also were conducted in tension, with the load applied parallel to the c-axis. In these cases, twinning was observed, and the resolved shear for plastic deformation by twinning was much lower that that for 〈c+a〉 slip observed in compression loading. This article is based on a presentation made in the symposium entitled “Defect Properties and Mechanical Behavior of HCP Metals and Alloys” at the TMS Annual Meeting, February 11–15, 2001, in New Orleans, Louisiana, under the auspices of the following ASM committees: Materials Science and Critical Technology Sector, Structural Materials Division, Electronic, Magnetic & Photonic Materials Division, Chemistry & Physics of Materials Committee, Joint Nuclear Materials Committee, and Titanium Committee.     

Sequential tripping strategy for a transmission network back-upprotection expert system

This paper describes a sequential tripping strategy used in a wide area back-up protection expert system (BPES) to combat situations in which protection relays have maloperated or information is missing. The BPES is an innovative back-up protection scheme designed to prevent the occurrence of widespread blackouts. The BPES evaluates the certainty that transmission lines are likely to be affected by the fault and uses a sequential tripping strategy to isolate the fault if a firm decision is not available due to maloperated relays and/or missing information. The mode of analysis and the sequential tripping strategy ensures that the BPES will clear a fault at minimum risk to the network. An example is included to demonstrate how the certainty factor based sequential tripping strategy is employed by the BPES to clear a fault which occurred on the South Western part of the UK National Grid System     

Bonding in cotton fiber from formaldehyde-free crosslinks

Cotton fabric was crosslinked with five agents, three of which were prepared form formaldehyde and two of which were formaldehyde-free. The formaldehyde-free agents produced less bonding between layers in the laminated microstructure of the cotton fiber. One agent, 4,5-dihydroxy-1,3-dimethyl-2-imidazolidinone, gave no evidence of any interlayer bonding. All five agents gave the same relationship between wrinkle recovery angle and molar substitution on the cotton up to moderate recovery angles, but only agents based on formaldehyde gave higher wrinkle recovery angles with additional reaction. Intralayer crosslinking did not reduce absorptivity, as shown by moisture regain and dye receptivity, but did restrict swelling in cupriethylenediamine hydroxide to the same extent as combined interlayer and intralayer crosslinking. The decrease in extensibility of treated fabric with increasing wrinkle recovery angle was the same with all agents. These results indicate the regions of the fiber that are important for each of these properties.     

New natural 2-acetoxy fatty acids using chemical ionization and electron impact mass spectrometry

The phospholipids of the spongePolymastia gleneni contain saturated long chain (C_22–30)-acetoxy fatty acids. Their structures were assigned based on chromatographic and spectrometric data as well as comparison with a synthetic sample. The use of capillary gas chromatography combined with chemical ionization and electron impact mass spectrometry was instrumental in the eludication of structures, since only a very small amount of crude lipids was available. Part 10 of “Phospholipids in Marine Organisms.” For Part 9 in this series, see reference 12.     

Laboratory accreditation in the UK

Two complementary national laboratory accreditation schemes are run by the National Physical Laboratory (NPL) to provide official recognition of competent British laboratories and an assurance of quality to their customers. The first of these, the British Calibration Service (BCS), was set up in 1966 to accredit laboratories to calibrate instruments, gauges and reference materials. In 1981 the National Testing Laboratory Accreditation Scheme (NATLAS) was formed to extend the service to all kinds of testing. Both BCS and NATLAS form an integral part of the UK national measurement system and were combined to form the National Measurement Accreditation Service on 1 October 1985.     

Combining multiple knowledge bases

Combining knowledge present in multiple knowledge base systems into a single knowledge base is discussed. A knowledge based system can be considered an extension of a deductive database in that it permits function symbols as part of the theory. Alternative knowledge bases that deal with the same subject matter are considered. The authors define the concept of combining knowledge present in a set of knowledge bases and present algorithms to maximally combine them so that the combination is consistent with respect to the integrity constraints associated with the knowledge bases. For this, the authors define the concept of maximality and prove that the algorithms presented combine the knowledge bases to generate a maximal theory. The authors also discuss the relationships between combining multiple knowledge bases and the view update problem