Rheological,thermal, and morphological properties of blends based on poly(propylene), ethylene propylene rubber,and ethylene-1-octene copolymer that could result from end of life vehicles: Effect of maleic anhydride grafted poly(propylene)

The objective of this work is to study the properties of blends that could result from the recycling of end-of-life vehicles (ELV). While ethylene propylene rubber (EPR) and ethylene propylene diene monomer (EPDM) have been used extensively as elastomeric additives in poly(propylene) (PP), they can be substituted by ethylene-1-octene copolymer (EOC). As a consequence, the matter resulting from the sorting of ELV might be more complex and made of PP, EPR, and EOC. The effect of incorporating EOC [that is a polyethylene elastomer (PEE)] and maleic anhydride grafted polypropylene (PP-g-MAH) on the rheological, thermal, and morphological properties of PP/EPR blends has been investigated. Blends of various compositions (with and without compatibilizer) were prepared using a corotating twin-screw extruder. The results were compared to the ones presented by a commercial (PP/EPR) blend. The EPR phase is dispersed in the form of spherical particles in (PP/EPR). The EOC phase is dispersed in the form of aggregated particles. Dynamic viscoelastic and differential scanning calorimetry properties of (PP/EPR)/EOC blends shows the incompatibility of the components even in presence of PP-g-MAH copolymer. POLYM. ENG. SCI., 47:1009–1015, 2007. © 2007 Society of Plastics Engineers     

Sintering-driven effects on the band gap of (Pb,La)(Ti,Ni)O3 photovoltaic ceramics

In this work, the influence of the sintering temperature on the physical properties of (Pb_0.8La_0.2)(Ti_0.9Ni_0.1)O₃ (PLT-Ni) ceramics is reported. The experimental data revealed that the energy band gap of PLT-Ni ceramics could be tailored from approximately 2.7 to 2.0 eV by changing the sintering temperature from 1100°C to 1250°C. It is demonstrated that the simple substitution of Ti⁴⁺ by Ni²⁺ cations is effective to decrease the intrinsic band gap while increasing the tetragonality factor and the spontaneous polarization. However, the additional red-shift observed in the absorption edge of the PLT-Ni with increasing the sintering temperature was associated with a continuous increase in the oxygen vacancies () amount. It is believed that the impact of the creation of these thermally induced is manifold. The presence of and Ni²⁺ ions generate the Ni²⁺- defect-pairs that promoted both a decrease in the intrinsic band gap and an additional increase of the tetragonality factor, consequently, increasing the spontaneous polarization. The creation of Ni²⁺- defects also changed the local symmetry of Ni²⁺ ions from octahedral to a square pyramid, thus lifting the degeneracy of the Ni²⁺ 3d orbitals. With the increase in the sintering temperature, lower-energy absorbing intraband states were also formed due to an excess of , being responsible for an add-on shoulder in the absorption edge, extending the light absorption curve to longer wavelengths and leading to an additional absorption in “all investigated” spectrum as well.     

Boundary scan test,test methodology,and fault modeling

The test technique called boundary scan test (BST) offers new opportunities in testing but confronts users with new problems too. The implementation of BST in a chip has become an IEEE standard and users on board level are the next group to begin thinking about using the new possibilities. This article addresses some of the questions about changes in board-level testing and fault diagnosis. The fault model itself is also affected by using BST. Trivial items are extended with more sophisticated details in order to complete the fault model. Finally, BST appears to be a test technique that offers a high degree of detectability on board level, but for diagnosis, some additional effort has to be made.     

Capture device identification from digital images using Kullback-Leibler divergence

Multimedia Tools and Applications - It is proposed a forensic method for the capture device identification from digital images, which requires two elements: i) a digital image subject to...     

Dynamic Parameter Identification Based on Lagrangian Formulation and Servomotor-type Actuators for Industrial Robots

International Journal of Control, Automation and Systems - This article presents the design of a parameter identification model for industrial manipulator robots. This model includes the dynamics...     

Gelatin supports with immobilized laccase as sustainable biocatalysts for water treatment

Millimeter-size beads of gelatin are manufactured by dripping process to give enzyme supports qualified for micropollutants biodegradation in alternative wastewater treatment. The bead diameter is dependent on the tip diameter, the gelatin solution viscosity and the swelling of polymer chains in the collecting bath. Chemical crosslinking was performed with glutaraldehyde using optimal concentration to give mechanical and thermal properties suitable for application in stirred reactor in aqueous medium. Laccases from Trametes versicolor are grafted on the gelatin beads with glutaraldehyde. Sixty percentage of the initial enzymatic activity, evaluated by the oxidation of 2′-Azino-bis(3-ethylbenzothiazoline-6-sulfonic acid)diammonium salt (ABTS) is maintained after 10 successive cycles of reaction. Thermal stability at 60°C of immobilized biocatalysts is improved when compared to free enzymes (45% vs 10% of relative activity after 6 h of incubation). The simplicity of the procedure to form gelatin beads and their properties make them promising bio-based and biodegradable support for enzyme immobilization.     

Evaluation of the removal of n-butanol vapor by the poly(lactic acid)-zeolite-TiO2 composite and formation of by-products

The use of polymeric films incorporated with zeolite-TiO₂ composites associated with UV radiation can be an alternative in the removal of volatile organic compounds (VOCs) through the adsorption and photodegradation processes. This study produced poly(lactic acid) (PLA) films incorporated with 13× zeolite, TiO₂, and 13×-TiO₂ zeolite composite to remove n-butanol and evaluate the by-products generated in the process. The results showed that 13× zeolite and TiO₂ added individually or as a composite to PLA, gave the polymer matrix a significant increase in the removal capacity of n-butanol. The best performance was presented by the zeolite-TiO₂, composite, confirming a synergistic effect. However, the formation of CO and CO₂ exceeded the expected values, with the verification that the polymeric matrix underwent photodegradation action by TiO₂. The polymeric film only containing zeolite is the most suitable for the removal of VOCs, as it did not present degradation of the PLA, generating a lower concentration of by-products.     

Influence of deposited amine-functionalized Si-MCM-41 in polyacrylonitrile electrospun membranes applied for separation of water in oil emulsions

Among several oil/water emulsion separation technologies, the utilization of nanoparticle-decorated membranes with diverse functionalities has received considerable attention in recent years, particularly if the antifouling capacity can be improved. In this article, we propose a new membrane based on surface-hydrolyzed polyacrylonitrile electrospun membranes and/or decorated with amine-functionalized Si-MCM-41 nanoparticles to be used as oil/water emulsion separation treatment and to determine their antifouling ability. X-Ray photoelectron spectrometry, attenuated total reflectance Fourier transform infrared spectroscopy, and toluidine blue O assay, scanning electron microscopy, contact angle measurements for oil under water and thermogravimetry were used for characterizing the membranes and an assay of permeability was developed to quantify the diffusion of oil molecules across the electrospun membrane. The electrospun and/or decorated membranes showed an underwater oleophobic wettability, which can separate oil-in-water emulsions with 87% separation efficiency, results of fouling experiments, evaluated in terms of rejection and flux recovery ratio, exhibited good antifouling ability, but the membrane decoration process did not lead to superior outcomes compared with undecorated membranes.     

A finite volume–finite difference method with a stiff ordinary differential equation solver for advection–diffusion–reaction equation

A model for atmospheric pollutant transport is proposed considering an advection–diffusion–reaction equation. A splitting method is used to decouple the advection, diffusion and reaction parts. A scheme based on finite volume, finite difference and backward differentiation formula is used for solving an atmospheric transport-chemistry problem.     

A linear algebra approach to OLAP

Inspired by the relational algebra of data processing, this paper addresses the foundations of data analytical processing from a linear algebra perspective. The paper investigates, in particular, how aggregation operations such as cross tabulations and data cubes essential to quantitative analysis of data can be expressed solely in terms of matrix multiplication, transposition and the Khatri–Rao variant of the Kronecker product. The approach offers a basis for deriving an algebraic theory of data consolidation, handling the quantitative as well as qualitative sides of data science in a natural, elegant and typed way. It also shows potential for parallel analytical processing, as the parallelization theory of such matrix operations is well acknowledged.