Modeling the energy potential of biomass – H2RES

Modeling biomass as a renewable energy source poses many challenges with respect to feedstock variability, which are difficult to account for. It is found that at the preliminary stages of energy planning, heating value and moisture content of the feedstock are the most important factors. In addition, the effects of harvesting, transportation and storage are found to be significant even though they are often overlooked. Using the gathered information a biomass module for energy planning is created and integrated to H₂RES, a renewable energy planning program. Using this excel based software, a case study for a wood processing factory is performed, using the waste wood as feedstock. Comparing various scenarios, it is concluded that using a combination of solid oxide fuel cells, solar panels and steam turbines can satisfy the factories energy requirements with excess sold to the grid.     

The master sintering curves for BaTi0.975Sn0.025O3/BaTi0.85Sn0.15O3 functionally graded materials

The most important aim in the design and processing of functionally graded materials (FGMs) is to produce devices free from any deformation. Smart choices of different combination of graded layers, as well as the heating rate during sintering, are important for the fabrication of high-quality FGMs. In this study, BaTi_0.975Sn_0.025O₃/BaTi_0.85Sn_0.15O₃ (noted as BTS2.5 and BTS15, respectively) FGM was used as a model system for the construction of master sintering curves (MSCs) and estimation of the effective activation energies of sintering for different BTS graded layers. The MSCs were constructed, for BTS2.5 and BTS15 graded layers in FGMs, using shrinkage data obtained by a heating microscope during sintering at four constant heating rates, 2, 5, 10 and 20 °/min. The effective activation energies were determined using the concept of MSC; values of 359.5 and 340.5 kJ/mol were obtained for graded layers BTS2.5 and BTS15, respectively. A small difference of the effective activation energies of chosen powders made it possible for us to prepare high-quality FGMs, without delamination, distortion or other forms of defects.     

Correlation among sintering process,porosity, and creep deformation of refractory concrete

The aim of this paper is to establish the correlation among sintering process, porosity, and important thermo-mechanical property of refractory concrete, i.e., creep. Creep deformation was investigated according to the standard laboratory procedure applied at three temperatures: 1200, 1300, and 1400 °C. Corundum and bauxite-based refractory concretes were investigated. The concretes are varying in chemical and mineralogical composition. Both loss of strength and degradation of material occur when refractory concrete is subjected to increased temperature and compressive static load. Measuring of thermo-mechanical properties can indicate and monitor the changes within microstructure. Variation of refractory concrete microstructure, as a consequence of sintering process, during exposure to constant compressive load and constant elevated temperature during certain time-intervals was investigated using scanning electron microscope and Image Pro Plus program for image analysis. Obtained results of the investigation proved that creep can be useful method when type of refractory concrete is to be chosen for an application.     

Measurement of the transient electrical and shaft torques in an induction motor drive by the indirect two-speed method

Contents This paper presents a new method, called Indirect Two-Speed Method (ITSM), for obtaining electrical and shaft torques in an induction motor drive by means of measuring the speeds of both lumped-inertia elements assigned to a second order model. The measuring is realized by using high-resolution digital tachometers (represented by incremental encoders), two frequency measurement systems based on the Double-Buffered Method, digitalfiltering of the raw speed data and numerical differentiation of the filtered speed data.

---

Messung transienter Drehmomente eines Induktionsmotor-Antriebs mittels der Indirekten Zwei-Drehzahlen-Methode

Übersicht Im Beitrag wird ein neues Verfahren zur Ermittlung des elektrischen Moments und des Wellen-Drehmoments eines Induktionsmotor-Antriebs vorgestellt. Das als Indirekte Zwei-Drehzahlen-Methode (ITSM) bezeichnete Verfahren geht aus von einem mechanischen Modell zweiter Ordnung und mißt die Drehzahlen beider als konzentrierte Parameter betrachteten Drehmassen. Für die Durchführung werden hochauflösende digitale Tachometer eingesetzt. Die Frequenzmessung erfolgt durch ein Verfahren mit doppelter Pufferung, und es werden die Rohdaten nach digitaler Filterung numerisch differenziert.

     

Specific Heat and Electrical Resistivity of 53%Niobium-47%Titanium Alloy Measured by Subsecond Calorimetric Technique

This paper presents results of measurements of the specific heat and electrical resistivity of a 53%Ni-47%Ti superconducting alloy. Both properties were measured by a contact variant of the millisecond-resolution pulse calorimeter. W5%Re/W25%Re thermocouple thermometry enabled study from ambient temperature to 2000 K. Results are discussed, and their uncertainty is estimated.     

Dosimetric characteristics of Li2B4O7:Cu,Ag,P solid TL detectors

A two-mutation carcinogenesis (TMC) model is used as a bridge between cellular radiation biological effects and the incidence of cancer. This model has been applied to several sets of experimental animal and epidemiological data. In this paper the advantage of the model and the implications for radiation risks at low doses are discussed with respect to the age and dose dependence of cancer incidence and the effect of age at exposure on radiation risk; the link between the radiation effect and background cancer incidence and the transfer of radiation risk across different population groups; the implications of acute and protracted radiation exposures for risks at low doses and the dose-effect relationship for radium induced bone cancer.     

Light backscattering polarization patterns from turbid media: theory and experiment

We present both experimental measurements and Monte-Carlo-based simulations of the diffusely backscattered intensity patterns that arise from illuminating a turbid medium with a polarized laser beam. It is rigorously shown that, because of axial symmetry of the system, only seven elements of the effective backscattering Mueller matrix are independent. A new numerical method that allows simultaneous calculation of all 16 elements of the two-dimensional Mueller matrix is used. To validate our method we compared calculations to measurements from a turbid medium that consisted of polystyrene spheres of different sizes and concentrations in deionized water. The experimental and numerical results are in excellent agreement.     

The effect of kinetic and hydrodynamic factors on current efficiency in the chlorate cell process

An equation has been derived which relates the current efficiency of chlorate production to the operational parameters of the process and the constants connected with the events in the diffusion layer of the anode. The latter have been estimated using available literature data and the equation has been tested for the temperature dependence of current efficiency by comparison with experimental results. A fair degree of agreement has been achieved.Partly presented at the XXth CITCE Meeting, Strasbourg 1969.     

Activation energy of isothermal martensitic β-α′ transformation

The kinetics of isothermal - martensitic transformation in the U–0.45 wt % Mo alloy has been investigated. The specimens were quenched from the region (690° C) and held isothermally at temperatures from 120 to – 196° C (liquid nitrogen). By quantitative metallographic methods the percentage of the newly formed-phase was determined and the half-thicknessc and radiusr of plates calculated. The activation energy for nucleation period was estimated. It was found thatG depends linearly on temperature. The nucleation rateN was determined to be a parabolic function of temperature. A part of the T-T diagram below theM _s temperature was determined.